Seville Classics FRN04725 User manual

ASSEMBLY INSTRUCTIONS
3-Tier Bookcase (Model # FRN04725)
32 in ×13 in ×33 in
(81.3 cm ×33.0 cm ×83.8 cm)
Patents Pending
Classic Lines Collection (Page 5 of 5)
The full “Classic Lines” furniture collection can be found at
www.sevilleclassics.com
Media Center/Coffee Table (FRN04715)
Wine Rack (FRN04716)
Magazine Rack (FRN04717)
2-Tier Tower (FRN04721)
Assembly Instructions (Page 4 of 5)
CAUTION:
1) Do NOT overly tighten the screws. Doing so may
damage the unit.
2) Do NOT place the unit in high temperature area or
near appliances that emit large amount of heat.
3) Do NOT place the unit outdoor, as exposure to direct
sunlight may cause the color to fade.
4) Do NOT place the unit on uneven surfaces. Doing so
may cause the unit to tip over.
5) Examine the screws periodically and tighten them if
they are loose.
6) Weight capacity: 75 lb per shelf
If you are missing any parts, have any questions, or need
additional assistance in assembly, please contact our
bilingual (English & Spanish) Customer Service
Department at:
Seville Classics, Inc.
Torrance, CA 90501 USA
Telephone: [phone] toll free within USA
310-533-3800
Fax: [phone]
Monday through Friday 8:30am - 4:30pm
(Pacific Standard Time)
E-mail: [e-mail]
Website and Online Store: www.sevilleclassics.com
Rev. 06/10

Parts List (Page 1 of 5)
Please check all the parts you received according to the
parts list below. If you are missing any parts, please
contact our Customer Service Department. (Please refer
to page 4 of 5)
(A) (B)
Folded Bookcase (1 pc)
(A) Long Screw (9 pcs)
pre-inserted in the unit
(B) Short Screw (6 pcs)
(C)
(D)
Bracket (4 pcs)
Bracket Screw (8 pcs)
*Tool needed: Phillips Screwdriver
Assembly Instructions (Page 2 of 5)
Step 1: Use a Phillips screwdriver to loosen the 9 long
screws (A) that have already been pre-inserted in the unit.
Do NOT remove the screws from the unit. Simply loosen
them to allow the unit to unfold. Next, place the
compressed unit horizontally and position your hands to
carefully unfold the unit.
Please Note:
1) Do NOT place the unit vertical when unfold as this may
result in the unit suddenly unfolding and pinching your
fingers.
2) Find a flat surface or floor to assemble the unit. Using
an uneven surface or floor to assemble the unit may result
in uneven/unlevel shelves.
3) If the unit is uneven/unlevel after assembled, loosen
both screws (A and B), adjust the unit and then retighten
the screw (A and B).
Step 2: Refer to the picture on page 3 of 5. First, tighten
the 9 pre-inserted screws (marked “A” in the picture).
Next, screw in and tighten the 6 short screws into the 6
screw holes on the unit (these screw holes are marked
“B” in the picture). Do NOT over tighten the screws.
Assembly Instructions (Page 3 of 5)
Step 3: Use a Phillips screwdriver to screw in and tighten
a Bracket (C) using 2 Bracket Screws (D) at four corners
of the unit.
How to Fold the Bookcase (If Needed): First, fully
loosen and remove all 4 brackets (marked “C” in the
picture above) from the unit. Then, fully loosen and
remove all 6 short screws (marked “B” in the picture
above) from the unit. Next, fully loosen (about 5 turns),
but do NOT remove, the 9 remaining pre-inserted screws
(marked “A” in the picture above). Finally, carefully fold
down the unit. Please note that the unit CANNOT be
folded completely flat. Forcing the unit into a folded
position without first removing the 4 brackets, 6 short
screws and fully loosening the 9 pre-inserted screws may
result in irreparable damage to the unit.