Better Homes and Gardens Modern Farmhouse Console User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2017-04-24 Rev. 0001-A Factory: KONRIC
Modern Farmhouse Console
Stock # BH17-084-098-47
# BH17-084-099-96
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Modern Farmhouse Console
MODEL # BH17-084-098-47 / BH17-084-099-96
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to become out of alignment. If you find that the doors need to be
adjusted slightly, turn the appropriate screw as illustrated below.
1. TO ADJUST THE DOOR FORWARD OR
BACKWARD.
2. TO ADJUST THE DOOR TO RIGHT OR
TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
FITS UP TO MOST 70” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL
OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS I
NJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw Cam Bolt into the pre-drilled small holes on panel. Connect both panels together; making sure Cam
Bolt goes into pre-drilled hole on the end of panel with Cam Lock.
2. Insert Cam Lock into pre-drilled large hole on panel. Make sure arrow on Cam Lock is pointed toward
Cam Bolt.
3. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten Cam Lock clockwise.
4. Plug Cam Cap into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43
p

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Frame (Qty. 1) C- Right Side Frame (Qty. 1)
D- Fixed Shelf (Qty. 1) E- Bottom Panel (Qty. 1) F- Upper Partition Panel (Qty. 2)
G- Left Lower Partition Panel H- Right Lower Partition Panel I- Top Front Stretcher
(Qty. 1) (Qty. 1) (Qty. 1)
J- Bottom Front Stretcher (Qty. 1) K- Middle Stile (Qty. 2) L- Side Adjustable Shelf (Qty. 2)
M- Middle Adjustable Shelf (Qty. 1) N- Left Door (Qty. 1) O- Right Door (Qty. 2)
P- Center Support w/Leveler (Qty. 2) Q- Back Panel (Qty. 1) R- Stop Rail (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 31+1 extra) (Qty. 31+1 extra) (Qty. 37+1 extra)
(4) M4 x 38 mm Screw (5) M4 x 50 mm Screw (6) M3.5 x 15 mm Flat Head Screw
(Qty. 4+1 extra) (Qty. 8+1 extra) (Qty. 6+1 extra)
(7) M3.5 x 15 mm Washer Head Screw (8) Door Stopper (9) Shelf Pin
(Qty. 32+1 extra) (Qty. 3) (Qty. 12+1 extra)
(10) Cam Lock Cover Flat Tip Hex Wrench Glue
(Qty. 30+1 extra) (Qty. 1) (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (2)
(Included in plastic bag)
Tools required: Hex wrench (provided), Phillips screwdriver and hammer (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assembly the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), the Side Frames
(B and C), the Middle Stiles (K) and the Bottom Front Stretcher (J).
A
B
C
K
K
J
Cam Bolt
(27 used in this step)
②

7
Assembly Instructions
3. Securely screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (D).
4. With the pilot holes as a guide, fasten three Door Stoppers (8) to the Fixed Shelf (D) using two 15 mm
Flat Head Screws (6) per stopper.
2
D
6
8
Cam Bolt
(4 used in this step)
②
Door Stopper
(3 used in this step)
⑧
M3.5 x 15 mm Flat Head Screw
(6 used in this step)
⑥

8
Assembly Instructions
5. Insert three Wood Dowels (3) into the large holes on the front edge of Top Panel (A). Tap in with a
rubber mallet, if necessary. Make sure that you use a small amount of glue with both ends of all dowels.
6. Align the drilled holes on the Top Front Stretcher (I) with the inserted Wood Dowels (3) on Top Panel
(A), and then press them together. Secure the Top Front Stretcher (I) in place with four 38 mm Screws
(4) using a Phillips screwdriver.
Wood Dowel
(3 used in this step)
③
4
A
I
4
4
43
3
3
M4 x 38 mm Screw
(4 used in this step)
④

9
Assembly Instructions
7. With the pilot holes as a guide, attach two Upper Partition Panels (F) to the Fixed Shelf (D) with four 30
mm Wood Dowels (3) and four 50 mm Screws (5).
5
5
5
5
D
F
F
3
3
Wood Dowel
(4 used in this step)
③
M4 x 50 mm Screw
(4 used in this step)
⑤

10
Assembly Instructions
8. Attach the Lower Partition Panels (G and H) to the Fixed Shelf (D) with four 30 mm Wood Dowels (3)
and four Cam Locks (1).
Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①
1
3
D
G
H

11
Assembly Instructions
9. Attach the Bottom Panel (E) to the Lower Partition Panels (G and H) with four 30 mm Wood Dowels (3)
and four 50 mm Screws (5).
G
H
E
5
5
5
5
3
3
Wood Dowel
(4 used in this step)
③
M4 x 50 mm Screw
(4 used in this step)
⑤

12
Assembly Instructions
10. Attach the Bottom Front Stretcher (J) to the Bottom Panel (E) with two 30 mm Wood Dowels (3) and
three Cam Locks (1).
E
J
1
3
M8 x 30 mm Wood Dowel
(2 used in this step)
③
Cam Lock
(3 used in this step)
①

13
Assembly Instructions
11. Attach the Middle Stiles (K) to the Partition Panels (F, G and H) with two 30 mm Wood Dowels (3) and
six Cam Locks (1).
G
F
D
H
F
K
K
1
3
M8 x 30 mm Wood Dowel
(2 used in this step)
③
Cam Lock
(6 used in this step)
①

14
Assembly Instructions
12. Glue ten Wood Dowels (3) into the inner holes of the Fixed Shelf (D) and Bottom Panel (E) at both
ends. Align the large holes on the Left Side Frame (B) with the inserted Wood Dowels (3), then press
them together and fasten it in place by engaging five Cam Locks (1).
13. Repeat the previous step to attach Right Side Frame (C) at the other end.
Wood Dowel
(10 used in this step)
③
Cam Lock
(10 used in this step)
①
D
E
B
C
1
3
1
3

15
Assembly Instructions
14. Glue eight Wood Dowels (3) into the top inner holes of the Side Frames (B and C) and Upper Partition
Panels (F).
15. Ask for assistance to position the Top Panel (A) onto the inserted Wood Dowels (3) and attach it in
place by engaging eight Cam Locks (1).
Wood Dowel
(8 used in this step)
③
Cam Lock
(8 used in this step)
①
3
1
B
C
F
F
A

16
Assembly Instructions
16. Tightly screw two Center Supports (P) into the threaded inserts on the Bottom Panel (E).
EP
P

17
Assembly Instructions
17. Now, go back and securely tighten all the Cam Locks and Wood Screws. Make sure all the parts are
tight and there are no gaps between the parts. This will help keep the unit square.
18. Unfold the Back Panel (Q) and lay it to the back of the assembled unit. Make sure the margins along all
edges of Back Panel are equal. Screw the 15 mm Washer Head Screws (7) into the pre-drilled small
holes on the Back Panel (Q).
NOTE: We recommend attaching back panel with the screws at the corners first.
7
E
C
Q
M3.5 x 15 mm Washer Head Screw
(32 used in this step)
⑦

18
Assembly Instructions
19. Stand the unit upright.
20. Pick up the Left Door (N) and attach the extended hinge arms to the hinge bases installed on the Left
Side Panel (B). Loosen the bolt on the back of the hinge base for an easy fit. Align and insert the “U”
slot on the hinge arm under the bolt head on the back of the hinge base. Make sure that both door hinges
engage and function properly. Tighten the bolt on the hinge base to lock the hinges in place.
21. Repeat the same procedure to attach the Right Doors (O) at the opposite side.
22. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the
screws for a good fit. Refer to the hinge sticker on the door for adjustment.
1
B
C
H
N
O
O

19
Assembly Instructions
23.
Insert four Shelf Pins (9) into the desired holes in the sides of each compartment. Make sure that you
place the four Shelf Pins in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves
(L and M) onto the Shelf Pins.
24. Plug the Cam Lock Covers (10) onto the visible cams locks to conceal the cams.
B
GH
C
9
9
10
L
M
L
Shelf Pin
(12 used in this step)
⑨
Cam Lock Cover
(30 used in this step)
⑩

20
Assembly Instructions
NOTE: You must install the Stop Rail (R) to prevent the TV from tipping when placing your flat panel
television directly on the console.
25. Remove the paper backing from the Stop Rail (R), then properly align the Stop Rail with the top edge of
the stopper template on the front of the Top Panel (A). Press down on the Stop Rail to help adhesion.
26. Carefully remove the stopper template from the Top Panel (A).
NOTE: When you place the TV on the stand, make sure that the base of the TV is behind the Stop Rail
(R). This will help prevent the TV from sliding off your stand if your stand is accidently bumped or
tipped.
R
R
A
R