Better Homes and Gardens FLYNN BH16-021-199-11 User manual

PB 1
model# BH16-021-199-11
model# BH47-021-199-14
model# BH47-021-199-15
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
FLYNN SIDE TABLE
pecan
smoke gray
white

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BOTTOM PANEL
BACK PANEL
FIXED SHELF
FOOT [X4]
DRAWER FRONT
LEFT DRAWER SIDE
RIGHT DRAWER SIDE
DRAWER BACK
DRAWER BOTTOM
A
B
C
D
E
F
G
H
I
J
K
L
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Flat Head Screwdriver Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
3. C a m
x20
4. Flat Head Screw
x8
1. Wood Dowel
x18
2. Cam Bolt
x20
5. Cam Cover
x4

4
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

4 5
x2 x2 x2
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6
x3 x4 x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x3 x4 x4
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x4 x4 x4 x4
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m 5. Cam
Cover

8 9
x6 x6 x6
STEP 5
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 6

1110 11
x8
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 7
4. Flat Head
Screw

12
STEP 8

12 13
40 lbs. / 18.1 kg.
20 lbs. / 9.1 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

PB 1
model# BH16-021-199-11
model# BH47-021-199-14
model# BH47-021-199-15
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
MESA LATERAL FLYNN
Instrucciones de Ensamble
nuez
gris humo
blanco

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
PANEL INFERIOR
PANEL POSTERIOR
REPISA FIJA
PATA [X4]
CAJÓN FRONTAL
CAJÓN LATERAL IZQUIERDO
CAJÓN DERECHO
CAJÓN POSTERIOR
CAJÓN INFERIOR
A
B
C
D
E
F
G
H
I
J
K
L
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza Plana Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
3. L e v a
x20
4. Tornillo de Cabeza
Plana
x8
2. Tornillo de Leva
x20
1. Clavija de Madera
x18
5. Cubierta del Tornillo
x4

4
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

4 5
x2 x2 x2
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo de
Leva
3. L e v a
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6
x3 x4 x4
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo de
Leva
3. L e v a
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x3 x4 x4
PASO 3
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo de
Leva
3. L e v a
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.