Better Homes and Gardens Kane BHW-10020 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-06-03 Rev. 0001-A
Kane Triple Bunk Bed
Stock # BHW-10020
TWO ADULTS ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF
THE BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL
THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST
THE WALL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL.
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts,
and jump ropes.
Prohibit more than one person on upper bunk.
Maximum mattress thickness must not exceed 8 in. (20.32 cm). Surface of mattress must
be at least 5 in. (12.70 cm) below the upper edge of guardrails.
Use only mattress which is 74 in. (1.88 m) to 75 in. (1.90 m) long and 37 ½ in. (95.25 cm) to
38 ½ in. (97.79 cm) wide on the upper bunk.
Replacement parts, including additional guardrails, may be obtained from any of our
dealers.

3
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT
OR FALLS
 Follow the information on the warnings appearing on the upper bunk end
structure and on the carton. Do not remove warning label from bed.
 Always use the recommended size mattress or mattress support, or both, to help
prevent the likelihood of entrapment or falls.
 Surface of mattress must be at least 5 in. (12.70 cm) below the upper edge of
guardrails.
 Do not allow children under 6 years of age to use the upper bunk.
 Periodically check and ensure that the guardrail, ladder and other components
are in their proper position, free from damage and that all connectors are tight.
 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
 Always use the ladder for entering and leaving the upper bunk.
 Do not use substitute parts. Contact the manufacturer or dealer for replacement
parts.
 Use of a night light may provide added safety precaution for a child using the
upper bunk.
 Always use guardrails on both long sides of the upper bunk. If the bunk bed will
be placed next to the wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and
wall.
 The use of water or sleep flotation mattress is prohibited.
 STRANGULATION HAZARD – Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed; for example, but not limited
to, hooks, belts, and jump ropes.
 Prohibit more than one person on upper bunk.
 Keep these instructions for future reference.

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Upper Headboard Front / Footboard Back Post B- Upper Headboard Back Post C- Upper Footboard Front Post
(Qty. 2) (Qty. 1) (Qty. 1)
D- Upper Cross Assembly E- Upper Cap Rail F- Upper Ladder Side Rail
(Qty. 2) (Qty. 2) (Qty. 1)
G- Upper Short Guardrail Post H- Middle Headboard Front / Footboard Back Post
(Qty. 1) (Qty. 2)
I- Middle Headboard Back Post J- Middle Footboard Front Post K- Middle / Lower Cross Assembly
(Qty. 1) (Qty. 1) (Qty. 4)
L- Middle Ladder Side Rail M- Middle Short Guardrail Post N- Lower Left Front / Right Back Post
(Qty. 1) (Qty. 1) (Qty. 2)
O- Lower Left Back / Right Front Post P- Lower Ladder Side Rail Q-Mattress Side Rail
(Qty. 2) (Qty. 1) (Qty. 3)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
R- Long Guardrail S- Short Guardrail T- Mattress Support Slats
(Qty. 4) (Qty. 4) (Qty. 3)
U- Long Ladder Left Support V- Long Ladder Right Support W- Short Ladder Left Support
(Qty. 1) (Qty. 1) (Qty. 1)
X- Short Ladder Right Support Y- Ladder Step Z- Guardrail Support
(Qty. 1) (Qty. 8) (Qty. 4)
(1) 1/4” x 100 mm Bolt (2) 1/4” x 38 mm Bolt
(Qty. 24+1 extra) (Qty. 22+1 extra)
(3) M6.5 x 100 mm Tapping Bolt (4) M6.5 x 48 mm Tapping Bolt
(Qty. 40+2 extra) (Qty. 22+1 extra)
(5) M10 x 50 mm Wood Dowel (6) M4 x 30 mm Screw (7) Floor Protector (8) Bed Connector Pin
(Qty. 60+2 extra) (Qty. 54+2 extra) (Qty. 8+1 extra) (Qty. 8)
(9) Barrel Nut (10) Metal Bracket (11) M3.5 x 19 mm Screw Hex Wrench
(Qty. 24+1 extra) (Qty. 4) (Qty. 8+1 extra) (Qty. 2 )
Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).

6
ASSEMBLY INSTRUCTIONS
NOTE: Please follow the instructions carefully to insure a safe and sturdy bed. Do not fully
tighten the bolts until all rails and guardrails are attached.
1. Unpack the units and confirm that you have all hardware and required parts.
2. Locate one Upper Cap Rail (E) on a level and protected surface with the holes facing up.
3. Insert two 50 mm Wood Dowels (5) into the large holes of one Upper Cross Assembly (D) and attach it
to the Upper Cap Rail (E) using three 48 mm Tapping Bolts (4). Securely tighten the bolts with the
enclosed hex wrench.
4. Repeat the same procedure to combine the other Upper Cap Rail (E) with other Upper Cross Assembly
with warning label (D).
④ x 6 ⑤ x 4

7
ASSEMBLY INSTRUCTIONS
5. Insert four 50 mm Wood Dowels (5) into the end holes of the Upper Cross Assembly with warning
label (D). Attach the Upper Headboard Posts (A and B) to the Upper Cross Assembly (D) with four
100 mm Tapping Bolts (3). Tighten the bolts with the enclosed hex wrench.
6. Repeat the same procedure to attach the rest Upper Footboard posts (A and C) to the other Upper Cross
Assembly (D).
⑤ x 8
③ x 8

8
ASSEMBLY INSTRUCTIONS
7. Insert the 50 mm Wood Dowels (5) into the drilled large holes on the Long Guardrail (R) at both ends.
Attach two Long Guardrails (R) between the Upper Posts (A and B) with four 100 mm Tapping Bolts
(3).
8. Attach one Mattress Side Rail (Q) between the Upper Posts (A and B) with four 100 mm Bolts (1) and
four Barrel Nuts (9). Make sure the wood stoppers for slats attached on side rail are up and face inward.
9. Repeat the previous step to attach the Upper Ladder Side Rail (F) between the Upper Posts (A and C).
⑤ x 4
① x 8
⑨ x 8
③ x 4

9
ASSEMBLY INSTRUCTIONS
10. Lay one Mattress Support Slats (T) onto the strips on the Upper Ladder Side Rail (F) and the Mattress
Side Rail (Q). Insert and screw the 30 mm Screws (6) into the countersunk holes on each slat. Tighten
the screws using a Phillips screwdriver.
⑥ x 14

10
ASSEMBLY INSTRUCTIONS
11. Insert the 50 mm Wood Dowels (5) into the end large holes of the Short Guardrails (S) as a guide.
Attach two Short Guardrails (S) between the Upper Headboard Front Post (A) and Upper Short
Guardrail Post (G) with four 100 mm Tapping Bolts (3).
12. Fasten the Upper Short Guardrail Post (G) to the Upper Ladder Side Rail (F) with two 38 mm Bolts (2),
using the enclosed hex wrench.
⑤ x 4
② x 2
③ x 4

11
ASSEMBLY INSTRUCTIONS
13. With the pilot holes as a guide, align and attach one Guardrail Support (Z) to the center of the Long
Guardrails (R) and the Mattress Side Rail (Q) by using three 30 mm Screws (6) through the
countersunk holes and screw into place.
14. Repeat the same procedure to attach one Guardrail Support (Z) to the Short Guardrails (S) and the
Upper Ladder Side Rail (F).
⑥ x 6

12
ASSEMBLY INSTRUCTIONS
15. Insert four 50 mm Wood Dowels (5) into the end holes of the Middle Cross Assembly with warning
label (K). Attach the Middle Headboard Posts (H and I) to the Middle Cross Assembly (K) with four
100 mm Tapping Bolts (3). Tighten the bolts with the enclosed hex wrench.
16. Repeat the previous step to attach the rest Middle Footboard posts (H and J) to the other Middle Cross
Assembly (K).
⑤ x 8
③ x 8

13
ASSEMBLY INSTRUCTIONS
17. Insert the 50 mm Wood Dowels (5) into the drilled large holes of the Long Guardrail (R) at both ends.
Attach two Long Guardrails (R) between the Middle Posts (H and I) with four 100 mm Tapping Bolts
(3).
18. Attach one Mattress Side Rail (Q) between the Middle Posts (H and I) with four 100 mm Bolts (1) and
four Barrel Nuts (9). Make sure the wood stoppers for slats attached on side rail are up and face inward.
19. Repeat the previous step to attach the Middle Ladder Side Rail (L) between the Middle Posts (H and J).
③ x 4
⑤ x 4 ① x 8
⑨ x 8

14
ASSEMBLY INSTRUCTIONS
20. Lay one Mattress Support Slats (T) onto the strips on the Middle Ladder Side Rail (L) and the Mattress
Side Rail (Q). Insert and screw the 30 mm Screws (6) into the countersunk holes on each slat. Tighten
the screws using a Phillips screwdriver.
⑥ x 14

15
ASSEMBLY INSTRUCTIONS
21. Insert the 50 mm Wood Dowels (5) into the end large holes of the Short Guardrails (S) as a guide.
Attach two Short Guardrails (S) between the Middle Headboard Front Post (H) and Middle Short
Guardrail Post (M) with four 100 mm Tapping Bolts (3).
22. Fasten the Middle Short Guardrail Post (M) to the Middle Ladder Side Rail (L) with two 38 mm Bolts
(2), using the enclosed hex wrench.
⑤ X 4
② x 2
③ x 4

16
ASSEMBLY INSTRUCTIONS
23. With the pilot holes as a guide, align and attach one Guardrail Support (Z) to the center of the Long
Guardrails (R) and the Mattress Side Rail (Q) by using three 30 mm Screws (6) through the
countersunk holes and screw into place.
24. Repeat the same procedure to attach one Guardrail Support (Z) to the Short Guardrails (S) and the
Middle Ladder Side Rail (L).
⑥ x 6

17
ASSEMBLY INSTRUCTIONS
25. Insert four 50 mm Wood Dowels (5) into the large holes of the Lower Cross Assembly (K) at both ends.
Attach the Lower Headboard and Footboard Posts (N and O) to the Lower Cross Assembly (K) with
four 100 mm Tapping Bolts (3). Tighten the bolts with the enclosed hex wrench.
26. Repeat the same process to combine the remaining Lower Cross Assembly (K) and Lower Posts (N and
O) together.
⑤ x 8
③ x 8

18
ASSEMBLY INSTRUCTIONS
27. Attach the remaining Mattress Side Rail (Q) between the Lower Posts (N and O) with four 100 mm
Bolts (1) and four Barrel Nuts (9). Make sure the wood stoppers for slats attached on side rail are up and
face inward.
28. Repeat the previous step to attach the Lower Ladder Side Rail (P) between the Lower Posts (N and O).
① x 8
⑨ x 8

19
ASSEMBLY INSTRUCTIONS
29. Lay the remaining Mattress Support Slats (T) onto the strips on the Lower Ladder Side Rail (P) and the
Mattress Side Rail (Q). Insert and screw the 30 mm Screws (6) into the countersunk holes on each slat.
Tighten the screws using a Phillips screwdriver.
⑥ x 14

20
ASSEMBLY INSTRUCTIONS
30. Insert four Bed Connector Pins (8) into the holes on the top of Lower Posts (N and O) and tighten them
into place with four 38 mm Bolts (2).
② x 4
⑧ x 4