Better Homes and Gardens Farmhouse BH47-084-099-08 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-06-04 Rev. 0001-B Factory: DONPEA
65” Farmhouse Media Fireplace Console
Stock# BH47-084-099-08
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: 65” Farmhouse Media Fireplace Console
MODEL #: BH47-084-099-08
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to become out of alignment. If you find that the doors need to be
adjusted slightly, turn the appropriate screw as illustrated below.
1. TO ADJUST THE DOOR FORWARD OR
BACKWARD.
2. TO ADJUST THE DOOR TO RIGHT OR
TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN.
MAX
IMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
FITS UP TO MOST 65” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL
OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw Cam Bolt into the pre-drilled small holes on panel. Connect both panels together; making sure Cam
Bolt goes into pre-drilled hole on the end of panel with Cam Lock.
2. Insert Cam Lock into pre-drilled large hole on panel. Make sure arrow on Cam Lock is pointed toward
Cam Bolt.
3. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten Cam Lock
clockwise.
4. Plug Cam Cap into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1) C- Bottom Panel (Qty. 1)
D- Bottom Front Molding (Qty. 1) E- Bottom Back Stretcher (Qty. 1) F- Left Side Panel (Qty. 1)
G- Right Side Panel (Qty. 1) H- Left Lower Partition Panel (Qty. 1) I- Left Middle Stile (Qty. 1)
J- Right Lower Partition Panel (Qty. 1) K- Right Middle Stile (Qty. 1) L- Middle Crossbar (Qty. 1)
M-Top Front Stretcher (Qty. 1) N- Upper Partition Panel (Qty. 1) O- Left Door (Qty. 1)
P- Right Door (Qty. 1) Q- Adjustable Shelf (Qty. 2) R- Upper Back Panel (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
S- Lower Back Panel T- Stop Rail Fireplace Insert Remote control with battery
(Qty. 2) (Qty. 1) (Qty. 1) (Qty. 1)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 37+1 extra) (Qty. 37+1 extra) (Qty. 39+1 extra)
(4) M3.5 x 12 mm Screw (5) M4 x 50 mm Screw (6) M3.5 x 15 mm Washer Head Screw
(Qty. 12+1 extra) (Qty. 8+1 extra) (Qty. 32+1 extra)
(7) Straight Metal Bracket (Qty. 2) (8) Shelf Support (Qty. 8+1 extra) (9) Angle Metal Bracket (Qty. 2)
(10) Floor Leveler (11) Cam Lock Cover (12) Rubber Bumper
(Qty. 2) (Qty. 22+1 extra) (Qty. 4+1 extra)
Glue (Qty. 1) Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (2)
(Included in plastic bag)
Tools required: Phillips screwdriver and hammer (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), the Fixed Shelf
(B), the Bottom Panel (C), the Side Panels (F and G) and the Middle Stiles (I and K) using a Phillips
screwdriver.
Cam Bolt
(35 used in this step)
②
B
A
F
G
C
K
I

7
Assembly Instructions
3. Insert two Wood Dowels (3) into the inner holes of the Middle Crossbar (L). Tap it in with a rubber
mallet, if necessary. Make sure that you use a small amount of glue with both ends of all dowels.
4. Align the drilled holes on the Fixed Shelf (B) with the inserted Wood Dowels (3) on the Middle
Crossbar (L), and then press them together. Attach the Middle Crossbar (L) in place by engaging three
Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
Wood Dowel
(2 used in this step)
③
Cam Lock
(3 used in this step)
①
3
1
3
B
L

8
Assembly Instructions
5. Attach the Middle Left Stile (I) to the Left Lower Partition Panel (H) with two 30 mm Wood Dowels (3)
and two Cam Locks (1).
6. Repeat the same procedure to combine the Middle Right Stile (K) with the Right Lower Partition Panel
(J).
3
3
3
3
H
J
K
I
1
1
1
M8 x 30 mm Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①

9
Assembly Instructions
7. Attach the Lower Partition Panels (H and J) to the Fixed Shelf (B) with four 30 mm Wood Dowels (3)
and four Cam Locks (1).
B
H
J
Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①

10
Assembly Instructions
8. Attach the Bottom Front Molding (D) to the Bottom Panel (C) by using three 30 mm Wood Dowels (3)
and four Cam Locks (1).
9. Repeat the same procedure to attach the Bottom Back Stretcher (E) to the Bottom Panel (C).
3
1
3
3
3
1
3
3C
D
D
E
C
M8 x 30 mm Wood Dowel
(6 used in this step)
③
Cam Lock
(8 used in this step)
①

11
Assembly Instructions
10. Attach the assembled base to the Lower Partition Panels (H and J) with four 30 mm Wood Dowels (3)
and four 50 mm Screws (5).
Wood Dowel
(4 used in this step)
③
M4 x 50 mm Screw
(4 used in this step)
⑤
3
3
5
5
5
5
C
H
J
D

12
Assembly Instructions
11. Attach the Left Side Panel (F) to the Fixed Shelf (B) and the assembled base with five 30 mm Wood
Dowels (3) and five Cam Locks (1).
12. Repeat the same procedure to attach the Right Side Panel (G) at the opposite end.
1
13
3
F
G
B
C
E
D
Wood Dowel
(10 used in this step)
③
Cam Lock
(10 used in this step)
①

13
Assembly Instructions
13. With the pilot holes as a guide, align and attach two Angle Metal Brackets (9) to the front corners of the
assembled base, using four 12 mm Screws (4) per bracket.
4
4
9D
F/G
F
G
C
D
Angle Metal Bracket
(2 used in this step)
⑨
M3.5 x 12 mm Screw
(8 used in this step)
④

14
Assembly Instructions
14. Screw two Floor Levelers (10) into the threaded sockets on the Angle Metal Brackets (9) and set them
to the correct height.
Floor Leveler
(2 used in this step)
⑩
9
10
10
F
G
D

15
Assembly Instructions
15. Stand the assembled unit upright.
16. Secure screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (B) using a Phillips
screwdriver.
B
2
Cam Bolt
(2 used in this step)
②

16
Assembly Instructions
17. Attach the Upper Partition Panel (N) to the Fixed Shelf (B) with one 30 mm Wood Dowel (3) and two
Cam Locks (1).
3
B
1
N
M8 x 30 mm Wood Dowel
(1 used in this step)
③
Cam Lock
(2 used in this step)
①

17
Assembly Instructions
18. Attach the Top Front Stretcher (M) to the Top Panel (A) with three 30 mm Wood Dowels (3) and four
50 mm Wood Screws (5).
M4 x 50 mm Screw
(4 used in this step)
⑤
M8 x 30 mm Wood Dowel
(3 used in this step)
③
3
5
5
5
5
3
3
A
M

18
Assembly Instructions
19. Attach the Top Panel (A) to both Side Panels (F and G) and the Upper Partition Panel (N) with five
Wood Dowels (3) and six Cam Locks (1).
Cam Lock
(6 used in this step)
①
M8 x 30 mm Wood Dowel
(5 used in this step)
③
A
N
3
F
G

19
Assembly Instructions
20. Flip the previous assembly around at its front edges.
21. Using the pilot holes as a guide, fasten the Middle Crossbar (L) to the Middle Stiles (I and K) by
attaching two Straight Metal Brackets (7) at the joints, using two 12 mm Screws (4) per bracket.
Straight Metal Bracket
(2 used in this step)
⑦
M3.5 x 12 mm Screw
(4 used in this step)
④
7
4
K
I
L

20
Assembly Instructions
22. Pick up the Upper Back Panel (R) and align the pre-drilled holes against the upper long edge with the
pilot holes on the Top Panel (A). Attach the Back Panel (R) in place using the provided Washer Head
Screws (6).
23. Align and attach two Lower Back Panels (S) to the mantel with the provided Washer Head Screws (6).
6
S
R
S
M3.5 x 15 mm Washer Head Screw
(32 used in this step)
⑥