Better Homes and Gardens Lana Modern Cube Bookcase User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-06-30 Rev. 0001-A Factory: HESLTD
Lana Modern Cube Bookcase
Stock # BH48-084-099-05
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Lana Modern Cube Bookcase
MODEL # BH48-084-099-05
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton
before discarding. Remove all parts from carton and separate into groups as indicated
on part list. Please ensure all parts are included prior to assembly. Use of power tools
to complete assembly is not recommended.
M A X I M U M R E C
O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 30 lb. (13.7 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure
Cam Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of
Cam Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cap into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are
present before beginning assembly.
A- Left Upper Side Panel B- Right Upper Side Panel C- Left Lower Side Panel
(Qty. 1) (Qty. 1) (Qty. 1)
D- Right Lower Side Panel E- Top Panel F- Upper Fixed Shelf
(Qty. 1) (Qty. 1) (Qty. 1)
G- Partition Panel H- Lower Fixed Shelf I- Bottom Panel
(Qty. 2) (Qty. 1) (Qty. 1)
J- Adjustable Shelf K- Base Long Stretcher L- Base Short Stretcher
(Qty. 2) (Qty. 2) (Qty. 2)
M- Upper Back Panel N- Lower Back Panel
(Qty. 1) (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are
present before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M15 x 60 mm Wood Dowel
(Qty. 30+1 extra) (Qty. 30+1 extra) (Qty. 28+1 extra)
(4) M8 x 30 mm Wood Dowel (5) Shelf Pin (6) M4 x 50 mm Screw
(Qty. 8+1 extra) (Qty. 8+1 extra) (Qty. 12+1 extra)
(7) M3.5 x 15 mm Washer Head Screw (8) Cam Lock Cap Glue
(Qty. 44+2 extra) (Qty. 16+1 extra) (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
Tools required: Phillips screwdriver and rubber mallet (not provided).