Better Homes and Gardens WM1-BFCNSL-GY User manual

PB 1
model# WM1-BFCNSL-GY
model# WM1-BFCNSL-IV
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
gray
ivory
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
BEDFORD CONSOLE TABLE

2
TOP PANEL
SIDE ASSEMBLY [ X 2 ]
B O T T OM PANEL
B O T T OM RAIL [ X 2 ]
TOP RAIL [ X 2 ]
A
B
C
D
E
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST
删掉底板前后横中间的孔
侧框下横和底板前后横都要加锁L型角铁的引孔
delete the holes in the middle of
the bottom rail
add holes for L angle iron in side bottom rail
and bottom rail

3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Lock Washer
x 4
3. C a m
x16
4. Bolt
x 4
1. Wood D o w e l
x24
2. Cam Bolt
x16
6. Washer
x 6
用的36mm长的组合器杆
using 36mm cam bolt

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. Wall S c r e w
x 1
9. P an Head S c r e w
x13
10. Wall A ncho r
x 1
7. A llen W r enc h
x 1
8. A ngle I r o n
x 4
12. Wall S t r a p
x 1
内六角扳手58mm长，
4mm粗
Allen wrench L 58mm, W 4mm

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x 4 x 4 x 4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
3. Refer to page 5 for instructions on how to use the cam lock system.
1 . Wo o d
D o w e l
2. C am B o l t 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
侧框下横和底板前后横都要加锁L型角铁的引孔
组合器扣孔位置错了
the holes for wrench is
wrong
add holes for L angle iron in side bottom rail and bottom rail

7
x 6 x 4 x 4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
侧框下横和底板前后横都要加锁L型角铁的引孔
add holes for L angle iron in the side bottom rail and bottom rail

8
x 6 x 4 x 4
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
侧框下横和底板前后横都要加锁L型角铁的引孔
Add holes for the L angle iron in the side bottom rail and bottom rail

8 9
x4 x4x4 x1x8
x4 x4
STEP 4
4. Bolt 5. Lock
Washer
6. Washer 7. Allen
Wrench
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

10
x4 x12
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 5
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
8. Angle Iron 9. Pan Head
Screw

10 11
x1x1x1x1
x2
10
11
12
9
6
6
STEP 6
9. Pan Head
Screw
11. Wall
Screw
12. Wall
Strap
6. Washer
10. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
50 lbs. / 22.7 kg.
30 lbs. / 13.6 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# WM1-BFCNSL-GY
model# WM1-BFCNSL-IV
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
gris
marl
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
MESA DE CONSOLA
BEDFORD
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO [X2]
PANEL INFERIOR
RIEL INFERIOR [X2]
RIEL SUPERIOR [X2]
A
B
C
D
E
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Arandela Fijadora
x4
3. Leva
x16
4. Perno
x4
6. Arandela
x6
2. Tornillo de Leva
x16
1. Clavija de Madera
x24

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
11. Tornillo de Pared
x1
9. Tornillo de Cabeza
de Noria
x13
10. Taquete de Pared
x1
12. Cincha de Pared
x1
8. Soporte
x4
7.Llave Allen
x1

4 5
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

6
x4 x4 x4
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x6 x4 x4
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8
x6 x4 x4
PASO 3
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.