Bicker UPSI-IP-3 Series User manual

English
User Manual UPSI-IP-3 Series
Bicker Elektronik GmbH
Ludwig-Auer-Straße 23 |86609 Donauwörth·Germany
UPS SYSTEM
IP65

UPSI-IP-3 Series
Revision 1-0 2
Revision Directory
Date Change
21.09.2022
Revision 1-0
Initial version
Legend of used symbols
Symbol Description
Attention! Important hazard warning.
Do not dispose of in the domestic waste.
Warning of electrical voltage.

UPSI-IP-3 Series
Revision 1-0 3

UPSI-IP-3 Series
Revision 1-0 4
A Brief specification
UPSI-2406IP-38AC
24 V / 6 A
 Outdoor AC/DC UPS for extreme environments
in robust aluminium housing with
IP65 protection
 Already integrated LiFePO4 energy storage
(330 Wh)
Temperature range -20…+50°C
 Intelligent input current regulation
Regulated output voltage in battery mode
 Pressure compensation element to prevent
condensation inside
Input and output cable firmly installed
Optionally available: mounting sets for masts
LiFePO4
INSIDE
TECHNICAL DATA
Input voltage* 100…240 VAC nominal (±10%), active PFC
Input frequency 50…60 Hz nominal (±10%)
Input current IIN NOM (IOUT = 6 A, ICHARGE = 0): 0.74 A at 220VACIN / 1.58A at 100 VACIN
IIN MAX (IOUT = 6 A, ICHARGE = max): 0.9 A at 220VACIN / 2.1A at 100 VACIN
IIN CHARGE (IOUT = 0, ICHARGE = max): 0.3 A at 220 V ACIN / 0.65 A at 100 V ACIN
Inrush current <100A (at IIN = 220VAC)
Efficiency App. 90.5…91.5% at IIN NOM (IOUT = 6 A, ICHARGE = 0)
App. 87.5…88.5% at IIN CHARGE (IOUT = 0, ICHARGE = max)
Output voltage* Normal mode: 24 VDC, backup mode: 23.5 VDC,
(voltage drop up to 0.5 V, depending on load)
Output current 6 A nominal
Capacitive load 3000 µF (in nomal mode, at start, 0 A load)
Charging method CC / CV / CP
Protection Overcurrent protection and short circuit protection (UPS) at output,
Overtemperature protection (AC-DC converter)
Battery cold start function Yes
Mast mounting set Optional available
Battery Technology LiFePO4: 25 Ah / 330 Wh
Backup time See page after next

UPSI-IP-3 Series
Revision 1-0 5
Backup fuse B16 230V AC
20A/120V AC, IEC/EN Listed breaker, Type B
Icw
(Rated Short-Time-Withstand)
<6 kA
Input and output cable AC input cable: Lapp ÖLFLEX® CLASSIC 100 BK 0,6/1 kV, 3x1.5mm
(incl. PE), length app. 3 m starting from chassis, open end
DC output cable: Lapp ÖLFLEX® CLASSIC 110 LT, 2x1.5mm,
length app. 3 m starting from chassis, open end
Operating temperature Operating: -20…+50°C (incl. charge and discharge)**
Storage / Transport: -20…+55°C, (recommended SOC at storage: 80 %)
Operating altitude ≤ 3000m
Dimensions W / H / D 130 x 130 x 370 mm ± 0.5mm
(without cable outlets and mounting brackets)
Weight 7.7 kg (device without cables)
Degree of protection IP65 (EN 60529)
Protection class 1
EMC EN IEC 62040-2:2018, EN IEC 61000-3-2:2019
Standards EN IEC 62040-1
Approvals UL: n.a.
CB Scheme: IEC 62040-1
Unless otherwise specified, the values apply to measurements at +25 °C
*From/to housing , without cables
**-20…0 °C: At sub-zero temperatures, the charging time increases according to the physical properties of the cells (increased internal resistance).

UPSI-IP-3 Series
Revision 1-0 6
*Backup time depends on battery capacitance, load and temperature. At very high or low temperatures a reduction of backup time occurs.
Unless otherwise specified, the values apply to measurements at +25 °C
Backup time* UPSI-2406IP-38AC
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0,0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0
Backupzeit [h] LFP-13250S 0...1A
Backupme [h]
IOUT [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0 2 4 6 8 10 12 14 16 18 20
Backupzeit [h] LFP-13250S 0...20W
Backupme [h]
POUT [W]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0,0 0,5 1,0 1,5 2,0
2,5
3,0 3,5
4,0
Backupzeit [h] LFP-13250S 0...4A
Backupme [h]
IOUT [A]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0
10
20 30 40 50
60
70 80
90
100
Backupzeit [h] LFP-13250S 0...100W
Backupme [h]
POUT [W]
Iout [A]
Backup time [h]
Iout [A]
Backup time [h]
Pout [W]
Backup time [h]
Pout [W]
Backup time [h]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0,0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0
Backupzeit [h] LFP-13250S 0...1A
Backupme [h]
IOUT [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0 2 4 6 8 10 12 14 16 18 20
Backupzeit [h] LFP-13250S 0...20W
Backupme [h]
POUT [W]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0,0 0,5 1,0 1,5 2,0
2,5
3,0 3,5
4,0
Backupzeit [h] LFP-13250S 0...4A
Backupme [h]
IOUT [A]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0
10
20 30 40 50
60
70 80
90
100
Backupzeit [h] LFP-13250S 0...100W
Backupme [h]
POUT [W]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0,0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0
Backupzeit [h] LFP-13250S 0...1A
Backupme [h]
IOUT [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0 2 4 6 8 10 12 14 16 18 20
Backupzeit [h] LFP-13250S 0...20W
Backupme [h]
POUT [W]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0,0 0,5 1,0 1,5 2,0
2,5
3,0 3,5
4,0
Backupzeit [h] LFP-13250S 0...4A
Backupme [h]
IOUT [A]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0
10
20 30 40 50
60
70 80
90
100
Backupzeit [h] LFP-13250S 0...100W
Backupme [h]
POUT [W]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0,0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0
Backupzeit [h] LFP-13250S 0...1A
Backupme [h]
IOUT [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
0 2 4 6 8 10 12 14 16 18 20
Backupzeit [h] LFP-13250S 0...20W
Backupme [h]
POUT [W]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0,0 0,5 1,0 1,5 2,0
2,5
3,0 3,5
4,0
Backupzeit [h] LFP-13250S 0...4A
Backupme [h]
IOUT [A]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0
10
20 30 40 50
60
70 80
90
1
00
Backupzeit [h] LFP-13250S 0...100W
Backupme [h]
POUT [W]

UPSI-IP-3 Series
Revision 1-0 7
Derating UPSI-2406IP-38AC
0
1
2
3
4
5
-20 -10 0 10 20 30 40 50 60 70
Ambient temperature [°C]
IOUT [A]
6
Iout [A]
Ambient temperature [°C]
-20…0 °C: At sub-zero temperatures, the charging time increases according to the physical properties of the cells (increased internal resistance).
UIN = 100…264 VAC UIN = 90…99 V AC

UPSI-IP-3 Series
Revision 1-0 8
A Brief specification UPSI-2406IP-38AC................................................................. 4
B Introduction and description ............................................................................... 9
B1 Description of the product and its functions ............................................................................................9
B2 Intended use – devices......................................................................................................................................... 10
B3 Intended use – connecting cables................................................................................................................ 10
C Safety instructions .............................................................................................. 11
C1 Preventive measures and rules when operating the UPS system............................................. 11
D Technical Data ..................................................................................................... 12
D1 General Technical Data.........................................................................................................................................12
D2 Drawing........................................................................................................................................................................... 19
E Name / Address / Support E-Mail / Phone number of the manufacturer ....... 19
F General Data ........................................................................................................ 20
F1 Assembly and installation advice...................................................................................................................20
F2 Convection, installation position and mounting.................................................................................. 20
F3 Description of connectors................................................................................................................................... 21
F4 Connection................................................................................................................................................................... 22
F5 Initial operation..........................................................................................................................................................24
F6 Charging time.............................................................................................................................................................24
F7 Overcurrent / Short circuit / Overtemperature protection ........................................................... 24
F8 Backup time in battery mode........................................................................................................................... 25
F9 Behaviour in case of exceeding maximum backup time................................................................25
F10 Battery start...................................................................................................................................................................25
F11 Dynamic Powerboost............................................................................................................................................. 25
F12 Status LED...................................................................................................................................................................... 28
F13 Shutdown diagram.................................................................................................................................................. 29
F14 Recommendations for a long UPS service life......................................................................................... 30
F15 Maintenance................................................................................................................................................................30
F16 Disposal........................................................................................................................................................................... 30
F17 Disclaimer ......................................................................................................................................................................30
F18 Scope of delivery....................................................................................................................................................... 30

UPSI-IP-3 Series
Revision 1-0 9
B Introduction and description
Read carefully before initial operation!
This manual shall help the user to get familiar with the product and its components and features. It shall pro-
vide information as accurately and completely as possible.
The manual as well as all documents has to be read and followed strictly before installation. Otherwise in cer-
tain situations warranty and guarantee can be cancelled partly or completely. Any liability on the part of Bicker
Elektronik is excluded for possible existing errors as well as non-compliance with the instructions for use and
installation.
B1 Description of the product and its functions
The UPSI-2406IP-38AC (hereinafter also called UPS) is a AC/DC UPS systems with numerous digital features and
high performance. The UPSI-2406 is combined with an upstream AC/DC converter as well as an already inte-
grated LiFePO4 energy storage. The primary use of the UPS is to secure the supply during power failures
and/or voltage fluctuations. The application which should be protected is connected to the output of the
UPS. The device has IP65 protection and has been developed for the specific use under extreme conditions.
The device requires a rated dimensioned AC voltage (100…240 VAC nominal) at the input. After the input
voltage is applied, the UPS works in normal mode automatically. The output is activated and the integrated
energy storage device is charged simultaneously. The input current is dynamic and depends on the load
current at the output and the current battery charge current. The green status LED at the bottom of the device
lights up continuously when the UPS is in this state.
If the input voltage drops below the lowest nominal value, the UPS is switched to battery mode (also back-
up mode). In this state, the application at the UPS output is supplied via the energy storage device. The
backup time (also buffer time) depends on the value of the output current (= load current) of the UPS.
An important feature is that the output voltage in battery mode is always regulated to approximately
23.5VDC and does not decrease as the voltage of the energy storage device drops. If the UPS operates in
battery mode, the status LED is slowly flashing (1 Hz flashing). After having been operated completely in
battery mode, the recharging of the LiFePO4 battery has to happen within two weeks.
When the input voltage returns, the UPS is automatically switched back to normal mode and charging of the
energy storage device is continued.
The UPS can also be used for user-initiated shutdowns of the supply voltage or cycles. Application examples
are the replacement of larger batteries in vehicles in which the electronics should continue to be supplied, the
opening and closing of safety valves after a malfunction or the shutdown of a system.
A pressure compensating element on the bottom side of the housing prevents condensation inside the device.

UPSI-IP-3 Series
Revision 1-0 10
B2 Intended use – devices
This device is primarily designed for use under difficult and extreme environmental conditions and can be
used both indoors and outdoors. It has been developed for professional use in areas such as industrial control,
communication and measurement technology. This product must not be used in devices or systems in which
a malfunction leads to serious injuries or endangers human life.
Unlike the standard models of the UPSI series (Open Frame or DIN-rail mounting), this device has IP65 protec-
tion. This means that the components mounted in the housing (UPS PCB and energy storage) are completely
protected against contact and dust (IP6x) as well as against water jets from any direction (IPx5) according to
EN60529.
B3 Intended use – connecting cables
The fixed connection cables may only be used with the device in accordance with the manufacturer‘s speci-
fications.
The input cable (type „Typ „ÖLFLEX® CLASSIC 100 BK 0,6 / 1 kV“ from the LAPP brand) as well as the output
cable (type „ÖLFLEX® CLASSIC 110LT“ from the LAPP brand) are coldflexible control an connection cables for
occasional flexible use and fixed installation under medium mechanical stress. They are also suitable for use in
dry, damp or wet areas.
If using outdoors, observe the indicated temperature range. They are for occasional, non-automated move-
ments, also when temperatures are low. They meet the requirements for slow rotary movements. The maxi-
mum tensile load is 15 N/mm of conductor cross-section during installation and operation. Compulsory
guidance is not permitted.

UPSI-IP-3 Series
Revision 1-0 11
C Safety instructions
WARNING!
Disregarding of following issues can result in electric shock, fire, serious injury or death.
1. Care must be taken to ensure proper and professional connection of the device.
2. The device must not be exposed to fire and temperatures outside the specification.
3. The device may only be exposed to water jets up to a maximum water volume of 12.5l/min
(according to EN60529).
4. The device must not be opened, short-circuited, reversed, overheated or otherwise soldered/welded.
5. Improper use and opening of the device will void the warranty.
6. Changes or attempts to repair the device are to be omitted.
7. Effects of foreign objects on the device must be avoided (e.g. metal parts).
8. Do not put obviously damaged devices into operation (e.g. dents, burn marks, rough contamination).
9. Device must not be dropped.
10. All parts of the device and accessories must not be eaten or swallowed.
11. The device must not be operated with voltage and current values outside of the specification.
12. The UPS is supplied with voltage from both the input source and the energy storage. The latter is still
energized even after the input source has been disconnected.
13. The input and output cables have to be professionally secured against pulling.
14. The device may only be used as intended.
15. The national accident prevention and safety regulations must be observed.
16. The assembly of the device and the electrical installation have to be state of the art.
17. The electrical, thermal and mechanical limit values have to be observed.
C1 Preventive measures and rules when operating the UPS system
The voltage drop of the lines has to be kept in mind! A high load current at the output can lead to high voltage
drops if the lines are too long. If the voltage drop is too high, the threshold value may be undershot and an
unintentional power fail may be triggered. Even after the upstream supply has been disconnected, the device
continues to run for some time after the shortfall of the load sensor (no load detection).
A short direct at the output of the device can cause damage or destruction of the UPS. In the event of a fault,
electrolytes can escape in liquid and gaseous form.

UPSI-IP-3 Series
Revision 1-0 12
INPUT DATA
Input voltage 100…240 VAC nominal (±10%), active PFC
Input frequency 50…60 Hz nominal (±10%)
Inrush current <100 A (bei IIN = 220 VAC)
Current consumption
IIN NOM (IOUT = 6 A, ICHARGE = 0)
IIN MAX (IOUT = 6 A, ICHARGE = max)
IIN DYN (IOUT = IDYN.BOOST, ICHARGE = 0)*
IIN NO-LOAD (IOUT = 0, ICHARGE = 0)
IIN CHARGE (IOUT = 0, ICHARGE = max)
At 220 V ACIN
0.74 A
0.9 A
1.0 A
<100 mA
0.3 A
At 100 V ACIN
1.58 A
2.1 A
2.2 A
<100 mA
0.65 A
Power consumption
PIN NOM (IOUT = 6 A, ICHARGE = 0)
PIN MAX (IOUT = 6 A, ICHARGE = max)
PIN DYN (IOUT = IDYN.BOOST, ICHARGE = 0)*
PIN NO-LOAD (IOUT = 0, ICHARGE = 0)
PIN CHARGE (IOUT = 0, ICHARGE = max)
At 220 V ACIN
155 W
190…196 W
220 W
<2 W
62…63 W
At 100 V ACIN
156 W
205…210 W
221 W
<2 W
63…64 W
Efficiency App. 90.5…91.5 % at IIN NOM (IOUT = 6 A, ICHARGE = 0)
App. 87.0…88.5 % at IIN CHARGE (IOUT = 0, ICHARGE = max)
Internal input fuse 2x 5 A / 250 VAC
Switch-on time <5 sec
Switch-on time battery start (BS) <5 sec
Backup fuse B16 230V AC
20A/120V AC, IEC/EN Listed breaker, Type B
D Technical Data
D1 General Technical Data
All specifications at the housing inlet/housing outlet, without line losses, at ambient temperature of 25°C
*Max. 58 sec., depending on output power (see also „F11 Dynamic Powerboost“)

UPSI-IP-3 Series
Revision 1-0 13
OUTPUT DATA – NORMAL MODE
Output voltage* 24 VDC
Output voltage range* 24…23.4 VDC max.
(depending on load)
Capacitive load 3000 F (at start, 0 A load)
Output current
INOM
IDYN.BOOST*
ISFB
6 A
6…8 A
30 A (5ms)
Output power
PN(IOUT = 6 A, ICHARGE = 0)
PDYN.BOOST (IOUT = IDYN.BOOST, ICHARGE = 0)*
144 W
144…192 W
Overcurrent shutdown 6…8 A for max. 58 s*; 8…10.8 A for max. 100 ms;
>10.8 A for max. 5 ms
Short-circuit proof Yes
No-load proof Yes
OUTPUT DATA – BATTERY MODE
Output voltage 23.5 V DC
Output voltage range* 23.5…22.5 VDC
(depending on load)
Output current
INOM
IDYN.BOOST
ISFB
6 A
6…8 A
30 A (5ms)
Output power
PN(IOUT = 6 A, ICHARGE = 0)
PDYN.BOOST (IOUT = IDYN.BOOST, ICHARGE = 0)*
141 W
141…192 W
Overcurrent shutdown 6…8 A for max. 58 s*; 8…10.8 A for max. 100 ms;
>10.8A for max. 5ms
Short-circuit proof Yes
No-load proof Yes
Load current for battery start 6 A max. (SOC ≥10 %)
Switching time
normal mode
>> battery mode
<1 ms
All specifications at the housing inlet/housing outlet, without line losses, at ambient temperature of 25°C
*Max. 58 sec., depending on output power (see also „F11 Dynamic Powerboost“)

UPSI-IP-3 Series
Revision 1-0 14
ENERGY STORAGE
Installed type BP-LFP-13250S
Battery technology LiFePO4
Charging method CC / CV / CP
Nominal voltage UN13.2 V
End-of-charge voltage 13.8 V
Battery charging current ≤0.2 C (4.5…5 A)
Undervoltage protection As soon as the first cell reaches 2.5 V
Nominal capacity 25 Ah / 330 Wh
Charging time
(at ICHARGE = max, TAMB = 25 °C)
App. 6h…7h
Buffer time (at IOUT = 6 A, TAMB = 25°C) App. 1h 50min

UPSI-IP-3 Series
Revision 1-0 15
DATA AC INPUT CABLE
Type of cable ÖLFLEX® CLASSIC 100 BK 0,6/1 kV – conenction and control cable,
3G1,5
Article No. Lapp 1120463
Features Flame-retardant according to IEC 60332-1-2,
UV and weather-resistant according to ISO 4892-2,
ozone-resistant according to EN50396, coldflexible up to –30°C
Cable construction Fine wire strands of bare copper; PVC conductor isolation, cold
resistant, Cores stranded in layers; Sheath: PVC, cold-resistant, black
Length 3 m
Outside diameter cable 10.1 mm
Stranded wire cross section
2x Stranded wire (Power): each 1.5mm; 1x Stranded wire (PE): 1.5mm
Minimum bendig radius Occasional flexing: 15x outer diameter
Fest verlegt: 4x outer diameter
Temperature range Occasional flexing: –30°C…+70°C
Fixed installation: –40°C…+80°C
N (blue) L (brown)
Sheath Sheath
DATA DC OUTPUT CABLE
Type of cable ÖLFLEX® CLASSIC 110 LT – PVC-control cable, 2X1,5
Article No. Lapp 1120750
Features Flame-retardant according to IEC 60332-1-2,
UV and weather-resistant according to ISO 4892-2,
ozone-resistant according to EN50396, coldflexible up to –30°C
Cable construction Fine wire strands of bare copper; PVC conductor isolation, cold
resistant, Cores stranded in layers; Sheath: PVC, cold-resistant, black
Length 3 m
Outside diameter cable 6.3 mm
Stranded wire cross section 2x Stranded wire (Power): each 1.5mm
Minimum bendig radius Occasional flexing: 15x outer diameter
Fixed installation: 4x outer diameter
Temperature range Occasional flexing: –30°C…+70°C
Fixed installation: –40°C…+80°C
VOUT– (2)
VOUT+ (1)
PE (green/yellow)
AC input DC output

UPSI-IP-3 Series
Revision 1-0 16
GENERAL DATA
Flammability class according to UL 94 V0
Weight 7.7 kg (device without cables)
UPS connection in parallel No
UPS connection in series No
HOUSING
Degree of protection IP 65
Protection class I
Mounting type Mast or surface mounting (or equal)
Housing version Aluminium-cast housing, milled, FORMODAL® 024,
natural anodised
Dimension W / H / D 130 mm / 130 mm / 370 mm
(without cable outlets and mounting brackets)
ENVIRONMENTAL CONDITIONS
Ambient temperature (operation) –20…+50°C
Ambient temperature (start up without load) –20°C
Ambient temperature
(storage / transport)
–20…+55°C
(recommended SOC at storage: 80%)
Permitted humidity 5…95%
Operating altitude ≤3000 m
Climate class 3K24 (EN 60721-3-3:2020-5)
Degree of pollution 4
Overvoltage category 2
Indoor / Outdoor use Yes / Yes
STANDARDS
EMC EN 62040-2, EN 61000-3-2, EN 62040-1
Safety
APPROVALS
UL n.a.
CSA n.a.
CB Scheme IEC 62040-1

UPSI-IP-3 Series
Revision 1-0 17
INTERFERENCE IMMUNITY ACCORDING TO EN 62040-2 Uninterruptible Power Suppy
Systems – Part 2: Electromagnetic compatibility requirements (EMC)
Basic standard Fulfilled requirements according to EN 62040-2
Electrostatic discharge
EN 61000-4-2
Contact discharge
Air discharge
Comment
±4 kV
±8 kV
Criterion A
Electromagnetic HF field
EN 61000-4-3
Frequency range
Test field strength
Frequency range
Test field strength
Comment
80 MHz…1 GHz
10 V/m
1 GHz…6 GHz
3 V/m
Criterion A
Fast transients (Burst)
EN 61000-4-4
Test voltage
Comment
±2 kV
Criterion A
Surge voltage load (Surge)
EN 61000-4-5
Test voltage L–N
Test voltage L–PE, N–PE
Comment
±1kV
±2kV
Criterion A
Induced radio frequency fields
EN 61000-4-6
Frequency range
Interference level
Comment
0.15…80 MHz
10 V / AM80% / 1 kHz (Sine)
Criterion A
Power frequency magnetic field immunity
EN 61000-4-8
Test level
Comment
30A/m
Criterion A
LEGEND
Criterion A Normal operating behaviour within the defined limits.
Criterion B Temporary impairment of the operating behaviour, that is
corrected by the device itself.

UPSI-IP-3 Series
Revision 1-0 18
EMISSION ACCORDING TO EN 62040-2 Uninterruptible Power Supply Systems –
Part 2: Part 2: Electromagnetic compatibility requirements (EMC)
Basic standard Fulfilled requirements according to EN 62040-2
Conducted emission from the power port
CISPR 22
Frequency range
Comment
150kHz–30MHz
Class A
Electric field radiated emission
CISPR 22
Frequency range
Comment
30MHz–1GHz
Class A*
Electric field radiated emission
CISPR 22
Frequency range
Comment
1GHz–6 GHz
Class A
*To improve the emitted interference, Bicker Elektronik recommends installing the "Würth 74272722" ferrite (not in scope of delivery) in the DC
output cable of the UPS directly after the housing outlet (2 turns).
HARMONIC CURRENTS ACCORDING TO EN 62040-2 Uninterruptible Power Supply
Systems – Part 2: Part 2: Electromagnetic compatibility requirements (EMC)
Basic standard Fulfilled requirements according to EN 62040-2
Measurement of harmonic currents
EN 61000-3-2
Comment Passed

UPSI-IP-3 Series
Revision 1-0 19
D2 Drawing
130 mm
370 mm 420 mm
8 mm
100 mm
402 mm
18 mm
62 mm
28 mm
130 mm
4 mm
Unless otherwise stated,
Tolerance according to:
DIN ISO 2768 T1 - m
DIN ISO 2768 T2 - K
E Name / Address / Support E-Mail / Phone number of the manufacturer
Bicker Elektronik GmbH · Ludwig-Auer-Straße 23 · 86609 Donauwörth · Germany
E-Mail: [email protected] · Tel.: [phone]

UPSI-IP-3 Series
Revision 1-0 20
F General Data
F1 Assembly and installation advice
The installation of devices that are not ready to be plugged in is to be carried out by the respec-
tive network operator or by a registered specialist company, who will also assist in obtaining the
approval of the respective network operator for the installation of the device.
F2 Convection, installation position and mounting
In order to achieve the best possible convection, the device has to be mounted vertically on a stable wall or
other surface. This is the only way to operate in the specified technical areas. Other installation methods are
possible, taking into account the reduced performance range.
Required fastening aids such as dowels or other systems are to be selected according to the mounting surface
used.
A distance of at least 100 mm (10 cm) in all directions from the housing wall to other, neighboring devices
should be maintained. The devices comply with the IP protection class 65.
D C B A
A 4 x Hex spax screw,
6mm x 60 mm or longer
B 4x tension washer, 6.4 mm,
DIN 6796
C 4x 8 mm mounting dowels for wall
attachment
D 8mm hole
62
402
8
(4x)
Drilling template, dimensions in mm