Xtreme 2000VA Operating manual

S80i Sine Wave Line Interacve UPS
2000VA Model
User & Installaon Manual
www.xpcc.com | © 2015 Xtreme Power Conversion Corporaon. All rights reserved. (Rev 10/08/15)

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 2
Uninterrupble Power Supply
Product Overview
LCD Panel
Power Switch
LCD Display
1. Input voltage
2. Output voltage
3. AC mode indicator
4. Load level
5. Overload indicator
6. Baery mode indicator
7. Baery level
8. Low baery indicator
9. Fault indicator

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 3
Uninterrupble Power Supply
Rear View
1. Output Receptacles
2. AC Input
3. Circuit Breaker
4. Modem/Phone/Network Surge Protecon
5. RS-232 Communicaon Port
6. USB Communicaon Port
Installaon and Inial Startup
NOTE: Before installaon, please inspect the unit. Be sure that nothing inside the package is damaged.
Placement & Storage Condions
Install the UPS in a protected area that is free of excessive dust and has adequate air ow. Please place the UPS
away from other units at least 20 cm to avoid interference. Do NOT operate the UPS where the temperature and
humidity is outside the specic limits. (Please check the specs for the limitaons).
Connect to Ulity and Charging
Plug in the AC input cord to the wall outlet. For the best results, suggest to charge the baery at least 6 hours
before inial use. The unit charges its baery while connecng to the ulity.

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 4
Uninterrupble Power Supply
6 Hours
Connect the Loads
Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS
unit, then devices connected to the UPS will be protected by UPS unit.
Connect Modem/Phone/Network for Surge Protecon
Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of the UPS unit. Connect
from “OUT” outlet to the computer with another phone line cable.
Connect Communicaon Cable
To allow for unaended UPS shutdown/start-up and status monitoring, connect the communicaon cable one
end to the USB/RS-232 port and the other to the communicaon port of your PC. With the monitoring soware
installed, you can schedule UPS shutdown/start-up and monitor UPS status through PC.
Turn On/O the Unit
Turn on the UPS unit by pressing the power switch. Turn o the UPS unit by pressing again the power switch.
Important Safety Warning (SAVE THESE INSTRUCTIONS)
Please comply with all warnings and operang instrucons in this manual strictly. Save this manual properly
and read carefully the following instrucons before installing the unit. Do not operate this unit before reading
through all safety informaon and operang instrucons carefully.
CAUTION! Please transport the UPS only in the original package to protect against shock and impact.
CAUTION! To prevent the risk of re or electric shock, install in a temperature and humidity controlled indoor
area free of conducve contaminants. (See the specicaons for the acceptable temperature and humidity
range.)
CAUTION! To reduce the risk of overheang the UPS, do not cover the UPS’ cooling vents and avoid exposing the
unit to direct sunlight or installing the unit near heat eming appliances such as space heaters or furnaces.
CAUTION! Do not aach non-computer-related items, such as medical equipment, life-support equipment, mi-
crowave ovens, or vacuum cleaners to UPS.
CAUTION! Do not plug the UPS input into its own output.
CAUTION! Condensaon may occur if the UPS system is moved directly from cold to warm environment. The UPS
must be absolutely dry before being installed.

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 5
Uninterrupble Power Supply
CAUTION! Place cables in such a way that no one can step on or trip over them.
CAUTION! The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily acces-
sible. The UPS power cord must be connected to an earthed mains socket outlet for safety reasons.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other
liquid-containing vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF buon and disconnect the power cord from the
AC power supply to properly disable the UPS.
CAUTION! Do not aach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during UPS installaon in
order to reduce leakage current below 3.5mA.
Aenon: hazardous through electric shock. Also with disconnecon of this unit from the mains, hazardous volt-
age sll may be accessible through supply from baery. The baery supply should be therefore disconnected in
the plus and minus pole at the quick connectors of the baery when maintenance or service work inside the UPS
is necessary.
CAUTION! Servicing of baeries should be performed or supervised by personnel knowledgeable of baeries
and the required precauons. Keep unauthorized personnel away from baeries. CAUTION! When replacing the
baeries, use the same number and type of baeries.
CAUTION! Avoid touching eyes while working near baeries.
CAUTION! Have plenty of fresh water and soap nearby in case baery acid contacts skin, clothing, or eyes.
CAUTION! Do not disassemble the unit before contact with the qualied service center when service or repair is
required.
CAUTION! To reduce risk of injury, only use qualied baeries from qualied distributors or manufacturers. Any
unqualied baeries may cause damage and injury. Do NOT use old or overdue baeries. Please check the bat-
tery type and date code before installaon to avoid damage and injury.
CAUTION! Internal baery voltage is 12VDC. Sealed, lead-acid, 6-cell baery.
CAUTION! Do not dispose of baeries in a re. The baery may explode. Do not open or mulate the baery or
baeries. Released electrolyte is harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION! A baery can present a risk of electric shock and high short circuit current. The following precauon
should be observed before replacing baeries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on top of baeries.
5. Disconnect charging source prior to connecng or disconnecng baeries terminal.

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 6
Uninterrupble Power Supply
Trouble Shoong
Use the table below to solve minor problems.
Problem Possible Cause Soluons
No words display on the front panel
even though the mains is normal.
AC input is not connected well. Check if the input power cord is
rmly connected to the mains.
AC input is connected to the UPS
output.
Plug AC input power cord to AC
input correctly.
Baery backup me is shorter than
nominal value.
Baeries are not fully charged.
Charge the baeries at least 6
hours and then check the capacity
again. If the problem sll persists,
please consult your dealer.
Baeries defect. Contact your dealer to replace
the baeries.
Warning or fault icon is shown and
alarm is connuously sounding.
Fan is locked or not working. Check fans and nofy your dealer.
The UPS is overload.
Remove some loads rst. Before
reconnecng devices, please verify
the total loads match the UPS capa-
bility specied in the spec.
Low baery icon is shown on the
LCD screen. Low baery. Charge the UPS at least 6 hours.

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 7
Uninterrupble Power Supply
Specicaons
MODEL NUMBER S80i-2000
INPUT Capacity 2000VA/1400W
Voltage 220/230/240VAC
Frequency 50/60Hz
OUTPUT Voltage 230VAC
Waveform Pure sine wave
Frequency 50/60Hz auto sensing
Transfer me 4ms (typical)
BATTERY Baery type Sealed, maintenance-free lead acid
Baery quanty and size (2) 12V 10AH
Recharge 4–6 hours to 90% capacity
Runme at 50% load Up to 10 min
PHYSICAL UPS dimensions (W x D
x H) 5.7 x 15.6 x 8.1 in
Shipping dimensions 9.1 x 19.3 x 11.3 in
UPS weight 25.4 lbs
Shipping weight 28.0 lbs
Line cord 6, IEC C13 to Schuko
Receptacles (8) IEC C13
Cooling Fan cooled
ENVIRONMENT Operang temperature 32–104°F (0–40°C)
Humidity 0–90%
Altude 11,500  above sea level
INDICATORS & LCD display AC mode, baery mode, load/baery level, input/output voltage, overload fault, low
baery
ALARMS Data line protecon RJ45
APPROVALS FCC Class A, UL 1778, cTUV, RoHS
WARRANTY 2 years electronics and baery
COMMUNICATIONS INTERFACE USB
INCLUDED IN BOX Shutdown and monitoring soware, USB cable, user manual, detachable line cord

Xtreme Power Conversion Corporaon
S80i User’s Manual
Page 8
Uninterrupble Power Supply
Obtaining Service
If the UPS requires Service:
1. Use the TROUBLESHOOTING secon in this manual to eliminate obvious causes.
2. Verify there are no circuit breakers tripped.
3. Call your dealer for assistance. If you cannot reach your dealer, or if they cannot resolve the problem, call Xtreme
Power Conversion Corp Technical Support at 800.582.4524. Technical support inquiries can also be made at
[email protected]. Please have the following informaon available BEFORE calling the Technical Support
Department:
• Your name and address.
• The serial number of the unit.
• Where and when the unit was purchased.
• All of the model informaon about your UPS.
• Any informaon on the failure, including LED’s that may or may not be illuminated.
• A descripon of the protected equipment, including model numbers if possible.
• A technician will ask you for the above informaon and, if possible, help solve your problem over
the phone. In the event that the unit requires factory service, the technician will issue you a Return
Material Authorizaon number (RMA).
If you are returning the UPS to Xtreme Power for service, please follow these procedures:
1. Pack the UPS in its original packaging. If the original packaging is no longer available, ask the Technical
Support Technician about obtaining a replacement set of packaging material. It is important to pack the
UPS properly in order to avoid damage in transit. Never use Styrofoam beads for a packing material.
2. Include a leer with your name, address, dayme phone number, RMA number, a copy of your original
sales receipt, and a brief descripon of the problem.
3. Mark the RMA number on the outside of all packages. Xtreme Power cannot accept any package without
the RMA number marked on the outside of the boxes.
4. Return the UPS by insured, prepaid carrier to the address provided by the Technician.
5. Refer to the Warranty statements in this manual for addional details on what is covered.