Billion BiPAC 7401V(G)P R4 User manual

BiPAC 7401V(G)P R4
VoIP/ (802.11g) ADSL2+
Firewall Router
Quick Start Guide

Quick Start Guide

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
P
Pa ac ck ka ag ge e C Co on nt te en nt ts s
BiPAC 7401V(G)P R4 ADSL2+ Router
CD (containing manual, utility, QSG)
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
One 2dBi detachable antenna (Wireless model only)
Power adapter
RJ-45 to RS-232 Console Kit
Quick Start Guide
Splitter/ Micro-filter (Optional)
zDo not use the router in high humidity or high temperatures.
zDo not use the same power source for the router as other
equipment.
zDo not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
zAvoid usin
g
this
p
roduct and all accessories outdoors.
Warning
zPlace the router on a stable surface.
zOnly use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention
-1-

Quick Start Guide
H
Ha ar rd dw wa ar re e O Ov ve er rv vi ie ew w
The Front LEDs
The Rear Ports
Connect to the ADSL
/
telephone network with
RJ-11 cable (telephone).
Press the RESET button
for 6 seconds and abo
to restore the facto ve ry
default settings.
Connect to PC or an
office/home network of
10Mbps or 100Mbps with
UTP Ethernet cable. Port
4 can be either a LAN or
Console port at a time but
not both.
Connect with the
detachable antenna.
Lit orange when
power is ON. Lit red
means system is fai
Lit green when th l. e
system is ready.
wall 1 cable.
Lit green when one of
LAN ports is connected to
an Ethernet device.
Blink when data is being
Connect to the
telephone jack on the
with RJ-1
Transmitted / Received. Lit Green when the device is
successfully connected to an
ADSL DSLAM. (“line sync”)
sending/receiving data.
Lit green when the
SIP Registration is
OK.
Lit green when a wireless
connection is
established. Flash green
when the device is
Power ON/OFF
witch s
Lit green when the
inbound and outboun
calls are transm d itted
through PSTN.
Connect to an
analog phone
set with RJ-11
cable.
Lit red when WAN port fails to
get IP address. Lit green w
WAN port gets IP address
successfully. Lit off when
device in bridged mode or
hen
WAN connection not present.
Lit green when the
phone is off hook.
Connect it with
the supplied
power adapter.
Push to trigger W
Protected Set i-Fi up
function.
-2-

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
H
Ha ar rd dw wa ar re e C Co on nn ne ec ct ti io on n
* Note: For WPS configuration, please refer to th
e WPS section of User Manual.
H
Ha ar rd d
1. Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different countries.
w
wa ar re e I In ns st ta al ll la at ti io on n
Power Connection
LAN Connection2. Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
-3-

Quick Start Guide
3. Phone Connection
Connect RJ-11 cable to the router’s phone port and the analog phone set.
4. Line Connection
a) Connect RJ-11 cable to the router Line port and the splitter phone port.
b) Connect RJ-11 cable to the router DSL port and the splitter ADSL port.
c) Connect RJ-11 cable to the splitter Line port and the phone jack on the wall.
5. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.
-4-

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
6. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get
good speed/stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
S
Se et tu up p U Ut ti il li it ty y
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.
-5-

Quick Start Guide
C
Co on nn ne ec ct ti in ng g t to o t th he e R Ro ou ut te er r
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
T
Tr ro ou ub bl le es sh ho oo ot ti in ng g
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
P
Pr ro od du uc ct t S Su up pp po or rt t a an nd d C Co on nt ta ac ct t I In nf fo or rm ma at ti io on n
Most problems can be solved by referring to the Troubleshooting section in the User Manual.If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
C
Co on nt ta ac ct t B Bi il ll li io on n
WORLDWIDE
http://www.billion.com
BiPAC 7401V
(
G
)
P R4: V1.01EN
-6-