Billion BiPAC 7100 User manual

BIPAC-7100S / 7100
ADSL Modem/Router
Quick Start Guide

Billion BIPAC-7100S/7100 ADSL Modem/Router
1
Package Contents
Billion BIPAC-7100S/7100 ADSL Modem/Router
One CD-ROM containing the driver and online manual
One Quick Start Guide
One RJ-11 ADSL/telephone cable
One CAT-5 straight LAN cable
One power adapter (12VDC, 1A)
 Do not use the BIPAC-7100S / 7100 in high humidity or high
temperatures.
 Do not use the same power source for the BIPAC-7100S / 7100
as other equipment.
 Do not open or repair the case yourself. If the BIPAC-7100S /
7100 is too hot, turn off the power immediately and have it
repaired at a qualified service center.
Warning
 Place the BIPAC-7100S/7100 on a stable surface.
 Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
A
ttention
For more detailed instructions on configuring and using
the ADSL Modem/ Router, please refer to the on-line
manual.

Quick Start Guide
2
The Front Panel LEDs
 7100S
7 4 1
5 2
LED Meaning
1 PWR Lit green when power adapter is connected.
2 SYS When flash, it indicates that the device is working properly.
4 LNK Lit green when the LAN link is connected.
5 COL Flashes green when collision happens
7 ADSL When lit, it indicates that the ADSL (Line) port is connected to the
DSLAM and working properly.

Billion BIPAC-7100S/7100 ADSL Modem/Router
3
 7100
6
2
3
5
LED Meaning
2 PWR Lit green when power adapter is connected.
3 SYS When lit, it indicates that the device is working properly.
LAN1 Lit green when the LAN1 link is connected.
LAN2 Lit green when the LAN2 link is connected.
LAN3 Lit green when the LAN3 link is connected.
5
LAN4 Lit green when the LAN4 link is connected.
6 ADSL When lit, it indicates that the ADSL (Line) port is connected to the
DSLAM and working properly.

Quick Start Guide
4
The Rear Ports
 7100S
5 3 1
4 2
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 LAN
(connector
RJ-45)
Connect the supplied crossover cable to this port when
connecting to a NIC (Network Interface card) in PC.
Connect an UTP Ethernet cable to this port when connecting to a
LAN such as an office or home network.
4 RESET Press it to restore the factory default setting back
5 LINE
(connector
RJ-11)
Connect the supplied RJ-11 cable to this port when connecting to
the ADSL
BIPAC-7100 has 4 LAN Ports, each of them has the same function as
that of 7100S

Billion BIPAC-7100S/7100 ADSL Modem/Router
5
Connecting Your ADSL Router
Through Ethernet Port
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
4. Follow the “Configuring the Network Properties on a PC” section on page 8 to modify the
network settings.
 7100S
 7100

Quick Start Guide
6
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.

Billion BIPAC-7100S/7100 ADSL Modem/Router
7
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.

Quick Start Guide
8
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.