Billion BiPAC 7800GZ(L) User manual

BiPAC 7800GZ(L)
3G/ Wireless-G ADSL2+
(VPN) Firewall Router
Quick Start Guide

Quick Start Guide

Billion BiPAC 7800GZ(L) 3G/ Wireless-G ADSL2+ (VPN) Firewall Router
-1-
Package Contents
BiPAC 7800GZ(L) 3G/ Wireless-G ADSL2+ (VPN) Firewall Router
CD containing the on-line manual
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
One 2dBi Wireless detachable antenna
Two 3G antennae
Power adapter
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

Do not use the
router
in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.

Avoid using this
product
and all
accessories
outdoors.

Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention

Quick Start Guide
-2-
Hardware Overview
The Front LEDs
The Rear Ports
* Note: For WPS configuration, please refer to the WPS section of User Manual.
Connect it with
the supplied
power adapter.
Connect the suppl
ied
RJ-11 cable to this port
when connecting to the
ADSL/telephone
network
Press
for
more than
1 second to restore
the device to its
default mode
Connect your computer
to a LAN port using the
included Ethernet cable
(with RJ-45 cable)
When the device is booting, the
green light will be lit and the red
light will flash. When the system
is ready, it will be lit green. Lit
red when the device fails to boot
or when the device is in
emergency mode.
Insert a SIM card
into this slot.
Lit up steady when connected
to an Ethernet device. Lit
green when the speed of
transmission hits 100Mbps;
Lit orange when the speed of
transmission hits 10Mbps.
Blinking when data is
transmitted/received.
Lit green when the
device is successfully
connected to an ADSL
DSLAM. (“line sync”)
Lit green when 3G service is
ready. Blinking orange slowly
when 3G signal is weak;
blinking orange fast when 3G
signal is middle; lit up orange
steady when 3G signal is
strong. Lit off when there is
no 3G signal.
Power
ON/OFF
switch
Lit green when a wireless
connection is established. Flash
orange when WPS configuration is
in progress. However, if WPS fails
the LED will only lit for 1 min
before goes off. Blinking when
data is transmitted/received.
Connect the
detachable
antenna for
wireless
connection
Push WPS button to
trigger Wi-Fi Protected
Setup
function
*
Lit red when WAN port fails
to get IP address. Lit green
when WAN port gets IP
address successfully. Lit off
when the device is in bridge
mode or when ADSL
connection is absent.
Connect the detachable
antennas to these two
ports for 3G connection.
3G Antenna

Billion BiPAC 7800GZ(L) 3G/ Wireless-G ADSL2+ (VPN) Firewall Router
-3-
Hardware Connection
BiPAC 7800GZ(L) offers three modes to connect to the internet. Besides using ADSL, users can
set EWAN (Ethernet port # 4) or 3G for internet connection. BiPAC 7800GZ(L) also allows Dual
WAN connection: ADSL fail-over to 3G, EWAN fail-over to 3G, ADSL fail-over to EWAN, and
counter likewise.
ADSL fail-over to 3G
Broadband (EWAN) fail-over to 3G

Quick Start Guide
-4-
ADSL fail-over to EWAN

Billion BiPAC 7800GZ(L) 3G/ Wireless-G ADSL2+ (VPN) Firewall Router
-5-
Hardware Installation
1. 3G Connection
Slide the SIM card into the card slot of the device with the gold contact facing down
.
Make sure that the SIM card has been slid into the bottom of the slot
with a click.
When removing
the SIM card, press the SIM card again it will be ejected from the
card slot.
Warning
Before inserting or removing the
SIM card, you must
disconnect the router from the power adapter.
Attention
Connect the detachable
3G
antenna
e
to the two
jacks
on the back and right side of device as it shows as
above. Making sure they are firmly screwed in.

Quick Start Guide
-6-
2. Power Connection
Plug the supplied power adapter into the wall
jack and the other side to the router.
Please note that the plug type may differ according to country.
Please make sure
when press Power Switch the front LEDs will be lit or off.
3. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
4. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 4 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.

Billion BiPAC 7800GZ(L) 3G/ Wireless-G ADSL2+ (VPN) Firewall Router
-7-
5. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other
side to the phone jack on the wall.
6. Splitter/ Micro-filter Connection
Splitter / Micro-filters are important for ADSL installation, they help ensure that
high-frequency signals are directed to the ADSL modem, and low-frequency
signals are directed to the telephone or other analog voice-channel device to
prevent inter-modulation distortion and get good speeds and stable ADSL sync
rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.

Quick Start Guide
-8-
b) Micro-filter connection
If the installation has several telephones or other analog devices then an internal
micro-filter can be employed at each analog device.
E
Ea as sy y S Si ig gn n- -O On n
Make sure power on the device, Ethernet cable is connected to your PC and ADSL line is in
sync. Then open up a web browser and you will automatically be directed to the step-by-step
easy sign on configuration wizard which will guide you to complete the basic network
configuration to connect to the internet.
C
Co on nn ne ec ct ti in ng g t to o t th he e R Ro ou ut te er r
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.