Billion BiPAC 8800AXL User manual

BiPAC 8800AXL
Dual-band Wireless-AC 1300Mbps
ADSL2+ 3G/ G LTE Router
Quick Start Guide

Billion BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
- 1-
P
Pa ac ck ka ag ge e C Co on nt te en nt ts s
BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
CD containing the on-line manual
RJ-11 ADSL/ telephone cable
Ethernet (RJ- 5) cable
Power adapter
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

Do not use the
router
in high humidity or high temperatures.
 Do not use the same power source for the router as other
equipment.
 Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.

Avoid using this
product
and all
accessories
outdoors.

Place the router on a stable surface.
 Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention

Quick Start Guide
- 2-
H
Ha ar rd dw wa ar re e O Ov ve er rv vi ie ew w
T
Th he e F Fr ro on nt t L LE ED Ds s
T
Th he e R Re ea ar r P Po or rt ts s
*Note 1: Port #5 can be configured as an Ethernet Interface for normal LAN use.
*Note 2: For WPS configuration, please refer to the WPS section of User Manual.
Connect the
supplied power
adapter to this jack
.
Connect this port to the
DSL network with the
RJ-11 cable (telephone)
provided.
Connect the USB device
(Printer, USB 2.0 storage,
3G / G LTE USB modem)
to this port.
Lit green when
Wireless
connection established.
Blinking when data being
transmitted
/received.
When the system is ready,
the LED will be lit green.
Lit red when boot failure or
in emergency mode.
Lit Green when successfully
connected to a DSLAM (Line
sync.) Blinking when DSL
synchronizing or waiting for
DSL
synchronizing
.
Power ON
/
OFF switch
Lit
red
when WAN port fails to
get IP address. Lit green when
WAN port gets IP address
successfully. Unlit when the
device is in bridge mode or
WAN connection is
absent.
Connect a UTP Ethernet cable
(Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC
or an office/home network of
10Mbps /
100Mbps /1000Mbps.
Blinkin
g
g
reen when
WPS configuration
being in progress.
Press more than 2
seconds to switch
on /off wireless 2. G
.
Lit
Green when
USB activate on
modem.
Ethernet
#
1
-
:
Lit green when successfully connected to
a LAN device (PC, switch, etc). Blinking
when data being transmitted /received.
EWAN (Ethernet #5):
Lit green when successfully connected to
a WAN device (Fibre /Cable /xDSL modem,
etc). Blinking when data being transmitted
/received.
Connect this port to
the fibre /xDSL /Cable
modem with a UTP
Ethernet cable (Cat-5
or Cat
-
5e)
*1
.
Press more than 2
seconds to switch
on/off wireless 5G.

Billion BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
- 3-
H
Ha ar rd dw wa ar re e C Co on nn ne ec ct ti io on n
A
AD DS SL L R Ro ou ut te er r m mo od de e: :
Push WPS button to
trigger Wi-Fi Protected
Setup function.
*2
Press WLAN button more than
2 seconds to switch on /off the
whole wireless connectivity,
including wireless 2. G and
wireless 5G. Please Note that
the action is based on the
status of wireless 2. G, if now
the wireless 2. G is on, then
you press the WLAN button
more than 2 seconds to switch
off both wireless mode
s
.
After the device is powered on,
press it 5 seconds or above to
restore to factory default settings
(this is used when you can not
login to the router, e.g. forgot the
password)

Quick Start Guide
- -
B
Br ro oa ad db ba an nd d R Ro ou ut te er r m mo od de e: :

Billion BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
- 5-
3
3G G/ / G G L LT TE E R Ro ou ut te er r M Mo od de e
Hardware Installation
1. Power Connection
Plug the supplied power adapter in to the wall jack and the other side to the
router.
Please note that the plug type may differ according to country.

Quick Start Guide
- 6-
2. LAN Connection
Connect the supplied RJ-45 Ethernet ca le to one of the Giga it Ethernet ports, and
the other side to the PC’s Ethernet interface.
3. ADSL Connection
Connect the supplied RJ-11 phone ca le to the router’s ADSL port, and the other
side to the phone jack on the wall.
. EWAN Connection
Connect RJ-45 Ethernet ca le to the EWAN port and connect the other side to
another alternative road and device, such as Ca le / FTTH device or PON optic
lines. Please refer to User Manual for detail instruction.

Billion BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
- 7-
5. USB Connection
1) Print server and storage service through USB 2.0 port：FTP server and DLAN
media server supported.
2) The USB 2.0 ports support 3G/4G LTE modem connectivity ：Users can
conveniently access Internet via 3G/4G LTE, eliminating the limitations of the
wired network. This solution also employs an auto fail-over feature to ensure
always-on connectivity for SOHO users.
6. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get good
speed/sta le ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can e employed.

Quick Start Guide
- 8-
) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can e employed at each analog device.
E
Ea as sy y S Si ig gn n- -O On n
Make sure that device is powered on, Ethernet ca le is connected to your PC and ADSL line is
in sync. Then open up a we rowser and you will automatically e directed to the step- y-step
easy sign on configuration wizard which will guide you to complete the asic network
configuration to connect to the internet.
C
Co on nn ne ec ct ti in ng g t to o t th he e R Ro ou ut te er r
1. Open the we rowser and type http://192.168.1.25 in the rowser's address ox. This
num er is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report we page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
T
Tr ro ou ub bl le es sh ho oo ot ti in ng g
1. None of the LEDs are on when you turn on the router.
Check the connection etween the adapter and the router. If the error persists, you may have
a hardware pro lem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should e on for a port that has a PC
connected. If it is off, check the ca les etween your router and the PC. Make sure you have
uninstalled any software firewall for trou leshooting. Verify that the IP address and the su net
mask are consistent etween the router and the workstations.

Billion BiPAC 8800AXL Dual-band Wireless-AC 1300Mbps ADSL2+ 3G/ G LTE Router
- 9-
3. Frequent loss of ADSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected etween them and
the wall socket (unless you are using a Central Splitter or Central Filter installed y a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
pro lems with your ADSL connection, including causing frequent disconnections. If you have
a ack-to- ase alarm system you should contact your security provider for a technician to
make any necessary changes.
P
Pr ro od du uc ct t S Su up pp po or rt t a an nd d C Co on nt ta ac ct t I In nf fo or rm ma at ti io on n
Most pro lems can e solved y referring to the Troubleshooting section in the user manual. If
you cannot resolve the pro lem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
C
Co on nt ta ac ct t B Bi il ll li io on n
Billion Australia – http://au.billion.com
Basic Support Hotline – 08 7071 3886 (Basic Support)
Helpdesk – http://au.billion.com/helpdesk/ (Lodge a support ticket)
Billion Support Forums – http://au.billion.com/forums (Get help & suggestions from
Billion & other users)
Download site – http://au.billion.com/product/fd.php (Download latest firmware, drivers &
User Guides)
BiPAC 8800AXL: V1.01AU