Binatone CAPRICE CAPRICE 600 User manual

1

2

3

2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the mains adapter plug will reach an easily accessible 230-V AC
switch mains supply socket - never try to lengthen the mains power cable.
the telephone line cable will reach your telephone line socket or
extension socket.
it is not close to a sink, bath or shower, or anywhere else where it
might get wet.
it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset cord into the Handset. Plug the other end into
the jack on the left side of
the Base unit.
3. Place the Handset in the Base unit.
4. Plug the telephone line cord into the PHONE
LINE jack at the back of the Base unit.
Plug the other end into a
modular wall
jack.
5. Plug the power supply
cord into the POWER
jack at the back of the
Base unit. Plug the
other end to a 230 V
AC, 50 Hz mains
socket, with the switch
on the socket set to
OFF.
6. Switch ON the mains
power at the socket.
7. Lift the Handset and
check for Dial tone
in the earpiece.
Always use the telephone line
cord supplied with your Caprice
600. Other telephone line cords
may not work.
The Caprice 600 Base unit must
be used only with the supplied
mains adapter. Using any other
adapter may damage the unit.
4
Note: The Base unit
does not require a
battery.

3. Desk/Wall mount installation
5
To place the Caprice 600 on a desk, connect
the stand to the bottom of the phone in the
slots near the ringer cover as shown below.
Desk Mount
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the ringer
cover). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward (3) as shown below.
To place the Caprice 600 on a wall, connect
the stand to the bottom of the phone in the
slots near the battery cover as shown below.
Wall Mount
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.

6
Desk/Wall mount installation continue...
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the battery
cover). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Mark two points on the wall that are 137mm
apart to lay the fixing centers as shown below.
BE CAREFUL to check that there are no
electrical wires hidden in the wall.
Fix two screws (supplied with the unit) at the
marked locations, leaving approximately 7mm
between the wall and the the screw head.
Hang the cradle unit on the screws using the
wall mount slots. You may need to remove the
telephone from the wall and tighten the
screws so that the cradle is securely fixed and
does not wobble. Place the Handset on the
cradle with the parking hook on the cradle
arranged to fit in the parking recess under the
earpiece on the Handset.

7
4. Setting up the Caprice 600
The following section details how to set up your
telephone. Press the MENU button to enter the
Options menu and then use the UP or DOWN
buttons to cycle through the following options:
SET LANGUAGE
SET TIME/DATE
SET FLASH TIME
LCD CONTRAST
MESSAGE LENGTH
RINGS TO ANSWER
REMOTE ACCESS
EXIT OPTION
Note: The system will time out if you leave
more than 15 seconds between key presses.
!
With the phone in standby mode;
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP button to go to the language setting.
ÖThe display shows
SET LANGUAGESET LANGUAGE
SET LANGUAGESET LANGUAGE
SET LANGUAGE .
3 Press MENU button to confirm.
4 Press UP or DOWN button to select ENGLISH
(default), FRANCAIS, or ESPANOL.
5 Press MENU button to confirm.
6 Continue with programming, or press EXIT
button to return to standby mode.
SET
LANGUAGE
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
SET TIME/DATESET TIME/DATE
SET TIME/DATESET TIME/DATE
SET TIME/DATE .
3 Press MENU button to confirm.
ÖThe ‘year’ icon will be blinking.
SET TIME/
DATE
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.

Setting up continue...
8
4 Press UP or DOWN button to set the year.
5 Press MENU button to confirm.
ÖThe ‘month’ icon will be blinking.
6 Press UP or DOWN button to set the month.
7 Press MENU button to confirm.
ÖThe ‘date’ icon will be blinking.
8 Press UP or DOWN button to set the date.
9 Press MENU button to confirm.
ÖThe ‘hour’ icon will be blinking.
10 Press UP or DOWN button to set the hour.
ÖWhen setting the ‘hour’, the ‘AM’ or ‘PM’
icon will automatically turn ON to correspond
the hour time.
11 Press MENU button to confirm.
ÖThe ‘minute’ icon will be blinking.
12 Press UP or DOWN button to set the minute.
13 Press MENU button to confirm the TIME and
DATE setting.
14 Continue with programming, or press EXIT
button to return to standby mode.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
SET FLASH TIMESET FLASH TIME
SET FLASH TIMESET FLASH TIME
SET FLASH TIME .
3 Press MENU button to confirm.
4 Press UP or DOWN button to select 100MS
(default), 300MS, or 600MS.
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.
SET FLASH
TIME

Setting up continue...
9
5 Press MENU button to confirm.
6 Continue with programming, or press EXIT
button to return to standby mode.
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
LCD CONTRASTLCD CONTRAST
LCD CONTRASTLCD CONTRAST
LCD CONTRAST .
3 Press MENU button to confirm.
4 Press UP or DOWN button to select your
comfortable display viewing level (1~5). The
default setting is 3.
5 Press MENU button to confirm.
6 Continue with programming, or press EXIT
button to return to standby mode.
LCD
CONTRAST
To set the recording time for ICM and memo
messages of the Answering machine.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
MESSAGE LENGTHMESSAGE LENGTH
MESSAGE LENGTHMESSAGE LENGTH
MESSAGE LENGTH .
3 Press MENU button to confirm.
4 Press UP or DOWN button to select 1, 2, 3,
or 4 minutes. The default setting is 2 minutes.
5 Press MENU button to confirm the MESSAGE
LENGTH setting.
6 Continue with programming, or press EXIT
button to return to standby mode.
MESSAGE
LENGTH

Setting up continue...
10
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.
To set the number of rings before the machine
answers a call;
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
RINGS TO ANSWERRINGS TO ANSWER
RINGS TO ANSWERRINGS TO ANSWER
RINGS TO ANSWER .
3 Press MENU button to confirm.
4 Press UP or DOWN button to select TOLL
SAVER, 2, 3, 4, 5, 6, 7, 8, or 9 rings. The
default setting is 6.
ÖUse ‘TOLL SAVER’ when checking your
Caprice 600 for messages from a remote
location using long distance service or from a
pay phone. The Answering machine responds
after the 2nd ring only if you have a new
message waiting. If there are no new messages,
the phone will answer after the 4th ring. You
can then hang up after the 3rd ring to avoid
paying for the call.
5 Press MENU button to confirm.
6 Continue with programming, or press EXIT
button to return to standby mode.
RINGS TO
ANSWER
The REMOTE ACCESS is a three-digit code
you need if you call away from home to check
your messages. The default is 321. You can
change it to any three digits you want.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
2 Press UP or DOWN button until the display
shows
REMOTE ACCESSREMOTE ACCESS
REMOTE ACCESSREMOTE ACCESS
REMOTE ACCESS .
3 Press MENU button to confirm.
ÖThe first digit of the code will be blinking.
4 Press UP or DOWN button to set the first digit
of the REMOTE ACCESS code.
REMOTE
ACCESS