Binatone Caprice 670 User manual

1
Caprice 670
Caprice 670
Delete
2
0
Sto re /
Mute
OGM
Recall Pause/Redial Handsfree
ABC
5JKL
8TUV
4GHI
7PQRS
3DEF
6MNO
9WXYZ
MEMO
MENU/OK
1
FWDREW
Sto p
Calls
Mounting Stand
All manuals and user guides at all-guides.com
all-guides.com

2
- When the instruction simply say 'press' a button, this means you should press it
briefly then release it.
- When the instruction say 'press and hold' a button, this means you should keep
it pressed until the display changes or you hear a tone.
Important:
Microphone -For
speakerphone use
and answering
machine OGM &
Memo recording.
With TAM ON is standby mode,
press to select OGM1 or OGM2.
- To access the caller
display records, and
UP-DOWN (Calls) Buttons
to scroll through lists
and options.
- Press to delete individual
messages, memos, stored
DELETE Button
light - Turns ON
when using the
speakerphone.
SPEAKERPHONE
- Turns ON
when the TAM
is on. Flashes
when you
have new TAM messages.
MESSAGE light
numbers or Caller Display
records.
- Press to enter Options
MENU/OK Button
Contrast,
phone/TAM settings.
- Press to access the
Phonebook records.
(PHONEBOOK) Button
- Press to access the LNR lists
when in standby mode. Press to
insert a pause when dialing.
PAUSE/REDIAL Button
- You may need this function if your
phone is connected to a PBX, or if
you use BT Calling Features.
RECALL Button
- Press to make, answer, or end a call
using the speakerphone.
- Press and hold to record
message(s).
- Press and hold to record
Press during message
Button
- Press to play back
Press to pause playing of
a memo or message.
PLAY/PAUSE Button
Button - Press to stop recording
/STOP (ANSWER ON/OFF)
- Used to adjust the volume
level of the Speakerphone.
SPEAKER Volume control
when you have new
Caller Display records.
New call light
- Flashes
M1, M2, M3 one-Touch
Memory Buttons
your outgoing messages.
Press during message
playback to repeat the
current message or to
go back to the previous
or playback. Press and hold to
switch the answering maching
ON or OFF.
a memo.
playback to skip to the
next message.
messages and memos.
to
- Press
mouthpiece. Press to store
and M3) one
during a call
mute the microphone or
the (M1, M2
touch memory dialing
buttons
Menu to set the Date,
Time,Screen
Del ete
1
0
Sto re /
Mut e
OGM
Rec all P aus e/R edi al Ha nds fre e
ABC
5JKL
8TUV
4GHI
7PQRS
3DEF
6MNO
9WXYZ
MEM O
MEN U/O K
Cal ls
FWDREW
Sto p
2
HADNSFREE Button
STORE/MUTE Button
FWD/MEMO
OGM/REW Button
All manuals and user guides at all-guides.com

3
Phone You are connected to the telephone line - your
Handset is ‘offhook’.
Time Displays the time.
Date/Month Displays the day and month setting.
Speakerphone Appears when the speakerphone function is
turned ON.
Mute Appears when you press the MUTE button to
Message Appears only when viewing a Caller display entry
with a recorded answering machine message.
NEW The NEW icon only appears when viewing
New Caller Display records.
Caller Display
Record
Shows the total number of Caller Display records
when the caller display is being received or when
the call lists is being viewed.
mute the mouthpiece or microphone.
All manuals and user guides at all-guides.com

4
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the mains adapter plug will reach an easily accessible 230-V AC
switch mains supply socket - never try to lengthen the mains power cable.
the telephone line cable will reach your telephone line socket or
extension socket.
it is not close to a sink, bath or shower, or anywhere else where it
might get wet.
it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset cord into the Handset. Plug the other end into
the jack on the left side of the Base unit.
Note: The base unit doesn't
require a battery.
3. Place the Handset on
the Base unit.
4. Plug the telephone line cord into
the PHONE LINE jack at the back
of the Base unit. Plug the other
end into your telephone line socket 5. Plug the power supply cord
into the POWER jack at the
back of the Base unit. Plug
the other end to a 230V AC,
50Hz mains socket, with the
switch on the socket set to OFF
6.Switch ON the mains power at
the socket. Wait while the
7.Lift the Handset and check
for Dial tone in the earpiece.
Note:TheCaprice 670Base unit must be used
only with the Switch adapter Shen Zhen G.EREDIT
Always use the telephone
line cord supplied with your
Caprice 670. Other telephone
line cords may not work.
Make sure the plugs click
into place.
or extension socket.
display shows INITIALISATION,
then the announcement
Answering machine on.
Announcement one before
the display changes to the
“
”
standby screen.
Modular
Wall jack
Electronics Co.,Ltd.5E-AD070042-B.
All manuals and user guides at all-guides.com

5
3.Stand/ Half stand installation
To stand the Caprice 670 at a larger angle, fit
the stand to the bottom of the phone in the
slots
Stand Mount
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
Insert the rigid clips (1) of the stand into the slots
on the bottom of the phone (near the rear of
the base). Press down firmly until the flexible
clips (2) click into place.
The base stand can be fitted in two positions to tilt the base forward at
in the base, as shown below.
different angles.
(1) Full stand mount (2) Half stand mount
rigid clips stand
All manuals and user guides at all-guides.com