Bioenno Power CC Series User manual

Bioenno Power SC-4830JUD CC/CV Series User Manual
12V/24V/36V/48V CC/CV SOLAR CHARGE CONTROLLER FOR LFP
THIS CONTROLLER IS FOR USE WITH LITHIUM IRON PHOSPHATE BATTERIES ONLY
OVERVIEW
Thank you for choosing the Bioenno Power SC-4830JUD Series CC/CV Solar Charge Controller. Your
product comes in 30A Maximum Load Current and is designed to be used with Lithium Iron Phosphate
(also commonly known as LiFePO4 or LFP) batteries only. The controller uses our proprietary CC/CV
Constant Current/ Constant Voltage circuitry to ensure maximum compatibility and performance with
the Bioenno Power battery. Your Solar Charge Controller comes equipped with an LCD display with a
visual presentation of usage status for your solar system and additionally features our smart technology
chipset which allows your Solar Charge Controller to automatically function at the correct mode of
operation as well as the ability to manually adjust between different modes of operation and load
power delivery.

SPECIFICATIONS
Rated Voltage: 12V/24V/36V/48V
Maximum Load Current: 30A
Input Voltage Range: <50V*
Load Disconnect: 9.9V/11.2V/13.2V/14V (Depending on voltage of system)
Efficiency: 95%~97% (In optimum conditions)
Operation Temperature: -31°F to 131°F (-30°C to 50°C)
Dimensions: 7.3 in. x 3.66 in. x 2.08 in. (186mm x 93 mm x 53 mm)
Weight: 0.84 lbs. (0.38 kg)
*Note: This solar charge controller can accept any voltage under 50V but it will not boost the voltage if the panel voltage is less
than the battery voltage. Make sure your panel voltage is higher than your battery voltage for optimum performance.
OPERATION PROCEDURE ORDER
1) Make sure the total rated current of the Solar Panel Array and Load are less than the rated
current of your Solar Charge Controller –in this case your maximum current is 20A
2) Make sure the polarity of the wiring from your Solar Panel Array, Battery and Load are
correctly matched to prevent the risk of a short circuit which may damage unprotected
devices
3) Mount you Solar Charge Controller to your selected surface and fasten it securely using
screws
4) Check whether the Battery voltage and Solar Panel Array voltage is within the requested
range
5) Loosen the screw terminals on your Solar Charge Controller –there are 6 screw terminals
total from left to right in this order: Solar Panel Positive, Solar Panel Negative, Battery
Positive, Battery Negative, Load Positive and Load Negative
6) Connect the Battery’s input to your Solar Controller using the two screw terminals in the
middle marked with the Battery pictogram, you may need an adapter –attach the wiring
securely but do not over-torque your Solar Charge Controller’s terminals
7) Connect your Load to your Battery’s output using the Battery as the buffer between the
Solar Panel Array and the Load (we DO NOT recommend using the Load Terminals for most
uses) –attach the wiring securely but do not over-torque your Solar Charge Controller’s
terminals
8) Connect the Solar Panel Array to the Solar Panel Input on your Solar Charge Controller using
the two screw terminals on the left marked with the Solar Panel pictogram –attach the
wiring securely but do not over-torque your Solar Charge Controller’s terminals
9) Your Solar Charge Controller should assume standard operation herein

VARIABLE VOLTAGE/HIGH CURRENT DISPLAY
STATUS CODES
INDICATOR
STATE
DESCRIPTION
MEANING
CHARGE/
PANEL
No Icons
PANEL OFF, FUNCTION ICON OFF
No Solar Panel detected
Panel Icon On
Function Icon Off
PANEL ICON ON, FUNCTION ICON
NOT INDICATING
Solar charging stopped
Panel Icon On
Function Icon On
PANEL AND FUNCTION ICON ON,
BATTERY ICON IS SCROLLING
Solar Panels are
charging Battery
LOAD
Function Icon On
Light Bulb Icon On
BOTH INDICATORS ARE ON SOLID
Load is ON
Function Icon Flashing
Light Bulb Icon On
LOAD INDICATOR ON, FUNCTION
INDICATOR FLASHING
Load is OFF
BATTERY
Battery Icon Empty
NO BARS
Battery requires
charging
Battery Icon Scrolling
SCROLLING BARS
Battery is charging
Battery Icon Full
FULL BARS, NO SCROLLING
Battery is fully charged
INDICATOR ICONS
Solar Panel: Solar Panel (icon may be solid or flashing depending on current usage or situation)
Battery: Battery (icon may be solid, scrolling or empty depending on current usage or situation)
Load: Light Bulb (icon may be solid or flashing depending on current usage or situation)
Function: Arrow (icon may be solid or flashing depending on current usage or situation)

FAULTS AND REMEDIES
FAULT
PHENOMENON
REMEDY
Battery voltage is too low
Battery Symbol Flashing Empty
Detach Load, check the battery
voltage and manually recharge
the battery if necessary
Excessive load current/
Short circuit*
Load Symbol (Light Bulb) Flashing
Reduce the load current at the
load output
Check if there is a short circuit in
the load or wing
Contact Us
Mail: Bioenno Power E-mail: [e-mail]
12630 Westminster Ave Suite B Phone:[phone]
Santa Ana, CA 92706
Warranty
Please see the included warranty pamphlet for warranty information. You can also check www.bioennopower.com for more information.
*Note: In the event of a short circuit, your Solar Charge Controller trip an auto-reset fuse –disconnect load immediately, let it
stand for 10-20 minutes, the internal fuse will automatically reset during this period. Before resuming operation, confirm your
load does not exceed the 20A Maximum Load Current of your Solar Charge Controller.