Biogents BG-Sentinel 2 User manual

Updates for the manual can be found on the websites: www.biogents.com and bg-sentinel.com
Status: May 2016 BG-Sentinel 2
Mosquito Control
Instruction Manual
Yashika Solutions
8-1-293/E/1, Plot no 70, Dwaraka Nagar
Colony, Shaikpet, Hyderabad. TS. 500008
Land mark: Opposite to OASIS School,

2EN
Table of contents
Product components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembling the trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administering the carbon dioxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positioning of the trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power supply and electricity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4
7
8
10
11
11
12

3EN
1. Intake funnel
2. Funnel net
3. Catch bag (2x)
4. Trap cover
5. Inner cylinder with attached ventilator
6. Trap body
7. Battery cable
8. Power cord with transformer (optional)
9. BG-Lure cartridge (optional)
10. CO2emitter nozzle (optional)
Product components
1
4
5
7
3
8
6
9
10
2

4EN
Assembling the trap
1. Open the Biogents trap carrying bag and take out the
components [F1].
2. Unhook the eyelet on the carrying handle and pop up
the trap body [F2].
3. First attach the funnel net (optional) and then the catch
bag over the protruding ring of the intake funnel [F3].
Tighten the top part of the catch bag.
4. Insert the intake funnel with the attached funnel net and
catch bag into the opening on top of the cover [F4].
5. Unwrap the plastic label from the BG-Lure cartridge [F5].
6. Pop out the white Biogents disc from the hole in the co-
ver when using the BG-Lure cartridge [F6].
F3
F1
F2
F4
F5
F6
Please note:
The smell of the new material of the traps might
have repellent eects on the mosquitoes. Therefore,
we recommend to air out the traps by running them
outside for two weeks before using them in the eld
to get rid of the smell.

5EN
F8
6. Insert the desired attractant into the trap. When using
the BG-Lure cartridge it can be placed into the hole in
the cover [F7].
7. Connect the battery to the battery cable [F8]. Alterna-
tively you can plug in the power transformer [F10]. Con-
nect the open ends of the battery cable with the venti-
lator cable. Please pay attention to always connect with
the arrows in one line [F9].
F7
F11
F9
F10
8. When the power is turned on, the shutter will automa-
tically tilt open [F11]. When the power is shut o or if
the battery fails, the shutter automatically closes which
ensures that the caught mosquitoes cannot escape.

6EN
9. Alternatively, you can place the battery within the
body of the trap. For this purpose open the trap by
unhooking the clips of the cover [F12] and remove
the cover [F13].
10. Place the battery into the xed straps located on
the bottom of the body and tighten the strap [F14].
11. Connect the battery cable to the battery [F15] and
guide the other end of the cable out of the opening
on the side of the trap [F16].
12. Connect the open ends of the battery cable with
the ventilator cable [F17]. The trap is now running
and the shutter of the intake funnel will tilt open.
You can easily disconnect and connect the cables
to switch the trap o or on without the need of ope-
ning the trap body.
F12
F17
F15
F13
F14
F16

7EN
To clean the plastic parts of the trap and the catch bags, use
clear water. Do not use any cleaning agents or solvents be-
cause the residues from these products can have a repelling
eect for the mosquitoes and consequently reduce the catch
rate of the trap.
Replacing the catch bag
The intake funnel together with the catch bag can be used as
a collection and transportation unit. The new shutter in the
intake funnel can be xed for this purpose and will ensure
that no mosquitoes escape during transport.
1. To remove the mosquitoes, rst x the shutter of the in-
take funnel by pressing together the intake funnel at the
axis of the shutter and then pressing the tab down [F18].
The tab is now secured and the shutter cannot open.
2. Then remove the intake funnel with the catch bag by
turning it counterclockwise and pulling it out [F19].
3. Alternatively, you can also remove the catch bag from
the intake funnel. Lift the intake funnel approximately
10 cm out of the trap, keeping the catch bag within the
suction current of the ventilator to ensure no mosqui-
toes escape. Carefully pull the catch bag o the intake
funnel and simultaneously pull the cord of the catch bag
tightly shut. You can set the intake funnel on the side of
the trap while closing the catch bag [F20].
For further use of the insects (e.g. identication/classica-
tion) it is best to put them in a freezer for at least an hour to
kill them. Please be careful when handling the funnel when
taking it out of the freezer. The plastic of the cold funnel
may break easily when falling to the ground. After several
hours (or in some cases up to a day depending on ambient
temperature and humidity) the caught mosquitoes will dehy-
drate and die within the trap. The trap does not damage the
insects, but identication is complicated if the insects stay in
the trap for more than 3 days and dry out or if they get wet.
You should attach the catch bag to the intake funnel with the
seam facing outwards in order to avoid mosquitoes getting
stuck in the seam while emptying the catch bag.
F18
F19
F20
Maintenance and care

8EN
Without CO2the BG-Sentinel catches Aedes aegypti, Ae-
des albopictus and Aedes polynesiensis which are vectors
of Dengue, Chikungunya, Filariasis and Yellow fever. It also
catches some Culex species such as
Culex quinquefasciatus
and Culex pipiens ; however, the addition of CO2enables you
to catch a broader range of blood seeking species as well
as much higher numbers of the previous mentioned species.
Various sources of CO2can be used. The optional CO2nozzle
can be attached to a gas cylinder, any well insulated dry ice
container or another CO2 source that ts your preference and
that is placed away from the trap.
Fermentation of yeast:
Yeast-produced carbon dioxide can be produced by mixing
17.5 g of dry yeast, 250 g of sugar and 2½ L of tap water or
35 g of dry yeast, 500 g of sugar and 2½ L of tap water in
a 5 L bottle. Capturing the foam to prevent the foam from
entering the traps can be accomplished by a set up with two
bottles. See detailed information for this protocol in a pub-
lication at http://www.ncbi.nlm.nih.gov/pubmed/20973963.
CO2gas cylinders:
In order to supply the trap with the carbon dioxide (CO2) at-
tractant, a commercially available CO2 gas cylinder with two
or more kilograms can also be used. These can be acquired
or rented at drink retailers or bottle depots for a deposit. A
door-to-door delivery service may also be possible. We re-
commend a 10 kg gas cylinder which is also used in restau-
rants for draft beer and soda.
Attaching the pressure reducing regulator onto the CO2gas
cylinder:
The BG-Sentinel CO2trap includes a specialized pressure
reducing regulator that is preadjusted to a constant out-
put pressure of 0.7 bars. The pressure remains consistent
throughout the entire usage. Screw the pressure reducing
regulator onto the CO2gas cylinder by rotating the screw on
the end of the regulator onto the opening on the CO2cylin-
der and make sure it is tight by using a wrench or pliers [F21].
Administering the carbon dioxide
Adjusting the CO2consumption with the CO2Y-tube
containing the respective sinter plugs:
Biogents‘ sinter technology is an elementary component in
the Biogents’ catching system which optimizes the release
of CO2and allows the adaptability to the local and seasonal
conditions. Depending on the existing mosquito situation,
you can choose between two dierent release rates: 200
grams/day and 500 grams/day. This allows the adaptation of
the carbon dioxide emission to the local and seasonal mos-
quito situation.
When monitoring mosquito populations, the 500 grams/day
release rate is recommended.
The Biogents BG-Sentinel CO2set includes a CO2tube with
three endings. The two short ends at the Y-shaped connec-
tion each contain a sinter plug and can be attached to the
pressure reducing regulator. The dierent sinter plugs are
each marked with a colored band and label.
Attach either the red or blue end of the CO2Y-tube to the
pressure reducing regulator. On the regulator with a screw on
connection, unscrew the nut on the outlet, thread the end of
the CO2 tube through the nut, insert the end of the CO2tube
onto the outlet and re-screw the nut back onto the outlet
[F22].
F21 F22

The other end of the CO2Y-tube with the sinter plug that is
not attached to the regulator does not need to be closed o
or attached to anything. The resistance from the sinter plug
forces the entered CO2through the easier path down the CO2
tube towards the trap.
The following is a consumption table of CO2comparing the
two CO2 ow rates:
Attaching the CO2tube to the nozzle on the trap:
Fix the long end of the CO2tube (opposite end of the Y-con-
nection with sinter plugs) over the designated opening on
the CO2 emitter nozzle on the trap [F24]. Ensure a tight t to
avoid detachement of the tube from the nozzle.
Consumption Table of Carbon
Dioxide
CO2Tube with Sinter Plug
CO2Flow Rate in
ml / min
CO2Flow Rate in
grams / day
Number of days a 10kg CO2
cylinder lasts
Blue - CO2Flow Rate 70 200 50
Red - High CO2Flow Rate 175 500 20
Attaching the CO2emitter nozzle to the trap:
Fix the CO2emitter nozzle onto the BG-Lure cartridge [F23].
If the BG-Lure is not used, insert the CO2nozzle into the
same opening on the cover.
F24
F23
Tight t

10 EN
The correct placement of the trap is an important factor that heavily influences its effectiveness.
Position the trap in a location that is sheltered from wind, rainfall, and direct sunlight.
(Rainfall will not damage the trap as long as the fan is switched on.)
NOTE: The trap should not be placed too close to walls (min. distance of approx. 0,5 meter)
Optimal positioning:
• Ideal locations to position the trap are close to resting areas of mosquitoes such as bushes, shrubs, hedges, or any other
foliage; however, placing the trap in very tall grass or under dense bushes will impair its effectiveness.
• The trap should also be positioned close to mosquito breeding sites such as various kinds of temporary stagnant water
ranging from small lakes to collections of rain water in rain barrels or old tyres. Many mosquitoes do not need a large
amount of water for breeding; even a can lled with rain water can be an ideal breeding place.
Important: The trap and all its upper surfaces should be clearly visible to patrolling mosquitoes, so that its specialized appea-
rance is eective in attracting the mosquitoes. Therefore do not place the traps under very dense bushes. A distance of at least
0.5 meters above the top of the trap needs to be kept clear. Any distance lower will hinder the visual signals and air currents
of the trap and consequently reduce the catch rate. A location under a sparse bush with adequate distance above the trap is
a good position. Keep the trap out of strong wind. Strong winds not only deter the mosquitoes but can also aect the suction
from the ventilator decreasing the catch rate.
Positioning of the trap
Positioning examples:
Rain shelter

11EN
The ventilator requires a power source of 9 to 12 V DC (max. 280 mA). While a battery cable is included, an optional power
supply unit (EU Version, US version or Australian version with an input of 220V and an output of 12V) with tting plug con-
nection is also available.
When using batteries, we usually recommend 12 Volt motorcycle or car batteries. These are easily rechargeable and readily
available in most places. As a rule of thumb, you will need a battery capacity of 10 to 11 Ah for each trap with a 24 hr trapping
period (for a 48 hr period you will need a capacity of 20 to 22 Ah and so on). This includes a security factor which should give
you a peace of mind in most real-life situations.
Power supply and electricity
Weight: 1.7 kg
Dimension unfolded: 38 x 47 cm
Dimension folded in bag: 42 x 13 cm
Ventilator: 12V DC, 3.6 Watt
Switching power supply: AC Input 100 – 230V,
Frequency 60Hz/50Hz,
DC Output 12V 1A
Technical data
Sheltering the trap from rain:
Rain might disrupt the airow by clogging the pores of the cover. This causes a reduction in the suction power of the ventilator.
Therefore ensure that the trap is sheltered from rainfall. If the trap became very wet allow it to dry before the next monitoring.
Even though rainfall does not damage the trap, there are several negative eects of rain that might decrease the catch rate:
• The mosquitoes can be damaged and dicult to identify.
• Mosquitoes avoid rain and prefer sheltered positions. In sheltered positions the catch rate can be therefore higher.
• Rain clogs the pores of the cover which leads to a reduction of suction power causing the shutter to close.
• Other animals, such as snailes, are attracted by a wet trap and tend to creep into the trap.
If you don‘t nd a naturally sheltered position for the trap, it would be best to position the trap under a roofed area, or a self
made shelter to keep it out of direct rainfall.
It is important to comply with the following regulations when sheltering the trap from rain:
• Whatever is placed over the trap must be at least 0.5 meters above the top surface of the trap. Any distance lower will
hinder the visual signals and air currents of the trap and consequently reduce the catch rate.
• Make sure the shelter covers an adequate area around the trap, so that rain cannot enter from the sides.
• Make sure the shelter is stable and durable.

12 EN
Biogents AG
Weißenburgstr. 22
93055 Regensburg
Germany
www.biogents.com
Email: [e-mail]
Contact
Mosquito Control
Yashika Solutions
8-1-293/E/1, Plot no 70, Dwaraka
Nagar Colony, Shaikpet, Hyderabad.
TS. 500008
Land mark: Opposite to OASIS School,