biomag Lumina User manual

Pulsed Magnetic Therapy Device
EN The design and technical solution of the unit and the applicators are registered with the IPO CR
and other international institutions.
Modification of the appearance not affecting the functions is reserved.
The colour shown in the illustrations may vary from your particular model.
Date of issue: 3. 4. 2020
Authorised Distributor
User Manual EN
Lumina Lumina
Karel Hrnčíř - BIOMAG
Chomutice 81, 507 53 Chomutice
Product of Czech Republic
The European Union
www.biomag.cz
REV I 20/04
Patented
technology
2265
T1 / en

Data on Completeness of Product
Modern
rehabilitation
Serial number of set / Equipment / Mode
Lumina
Lumina
Device for home care
Device for professionals

Usermanual page | 1
List of abbreviations and symbols 2
1. INTRODUCTION  BASIC INFORMATION 3
Principles of safe operation – Method of use 4
Contraindications 5
List and descriptions of programs, purpose of application of the Biomag®magnetic therapy 5
2. DEVICE CONTROL 9
a) Device description 9
b) Basic operation – quick start 10
Simplified instructions for the Biomag®Lumina system operation 10
Example of proper connection of the Biomag®Lumina system before starting the application 11
c) Operation of the Biomag®Lumina system and other possible settings 12
3. APPLICATIONS 14
Range of possible use 14
Effects of low-frequency pulsed magnetic field 14
Selection and use of applicators 15
Brief plan of the low-frequency pulsed magnetic field application 16
Brief instructions for settings based on required therapeutic effects 16
When and how often to apply low-frequency pulsed magnetic field 17
Further information for low-frequency pulsed magnetic field applications 17
4. TECHNICAL SPECIFICATIONS 17
a) Technical description and specifications of the system 17
b) Technical description and specifications of applicators 21
Use of the applicators 21
Technical specifications of the applicators 22
Biomag®Lumina applicators 22
Light applicator AL16-LUM (Alfa) 24
c) Electromagnetic Compatibility (EMC) Information 25
5. OTHER INFORMATION 28
Maintenance 28
Service 28
Operation environment, storage, transport 28
Warranty 28
Health protection during work with low-frequency pulsed magnetic field 28
Troubleshooting for the Biomag®Lumina system 29
Contact information 29
Recommended literature 30
Contents

2| page Usermanual
List of abbreviations and symbols
List of symbols
Read the User Manual Alternating current (AC)
Device with protection class II Direct current (DC)
BF type applied part Basic program time
Electrical equipment intended for indoor use Keep away from moisture
Environmentally friendly disposal of the device Symbol for identical polarity of all
parts on one side of the applicator
Applicator polarity symbo Temperature limitation
Warning, important notice Humidity limitation
Manufacturer Limiting atmospheric pressure
Year of manufacture Serial number
Conformity marking for products placed on the market in the European Economic Area
SN
List of abbreviations
LPMF Low-frequency pulsed magnetic field
MIMF Maximum intensity of magnetic field
Hz Frequency unit = pulse rate
fFrequency = pulse rate
mT Unit of magnetic field intensity
INT Intensity
min Minute (abbreviation in the displayed
information)
EMC Electromagnetic compatibility
STI Safety technical inspection
Explanation provided
Seznam použitých ikon
List of all programs
MY PROGRAMS
Confirmation button
Navigation within the menu
Input for applicator
Power supply symbol
Next menu
Run the recommended program repeat
Information on the program
Continue with the program selection
Copy to MY PROGRAMS
Remove from MY PROGRAMS
Display the menu
Back
Display operation information
Display basic effects
Contraindications
System settings
Program INDIVIDUAL
Yes/No setting
Favourite programs
Transfer of programs
Time
Reminder setting
Sound/volume down
PIN1/PIN2
Language selection
Keyboard lock
Number of pre-paid applications
Battery
Application history
Program type
EASY/CLINIC programs
Activate rotary/synchronised programs
Gradual switch-on of the inputs
Number of my programs
Save/Do not save
Simplified mode EXTRA
The time in EXTRA mode
The intensity in EXTRA mode
3D connector / 2C connector
Avoid touching the display when holding, moving or manipulating
with the device.
nabitý vybitý
List of used device symbols

Usermanual page | 3
Biomag®Lumina
It is a device with a built-in power supply and a maximum of four separately
connectable applicators. This top quality device is a portable magnetic
therapy system, the features of which are based on the older system series
Biomag® (Biomag®89, Biomag®92, Biomag®duo, Biomag®Quattro,
Biomag®mini, Biomag®Family, Biomag®Laguna, Biomag®Litus,
Biomag® Mona, Biomag®Monada, Biomag®Monai, Biomag®Monada
plus) which belong among the most frequently used systems in the
healthcare sector.
Biomag®Lumina expands the features of the previous systems by
an option of gradual switch-on of the outputs to the applicators (
3D
technology). Another advantage of the Biomag®Lumina system includes
the possibility of using a battery, allowing the use of the device without
connection to the electrical grid.
Intended purpose
Biomag®Lumina is an active therapeutic device. A medical device, whether
used alone or in combination with other medical devices, to support bio-
logical functions in order to induce positive effects in the body through the
following therapeutic effects:
• Pain-relieving (analgesic)
• Myo-relaxing (relief from spasms)
• Anti-swelling (anti-oedema)
• Vasodilating (widening the bloodstream)
• Metabolic-detoxifying (eliminating harmful substances)
• Healing (with support of regeneration, anti-inflammatory
and anti-rheumatic)
Designed for use on intact skin through a protective layer, such as a dispos-
able or other sanitary napkins.
Operator profile (who can operate the device)
The Biomag®Lumina device operates:
• trained medical staff in the environment of the medical facility
(doctor, rehabilitation worker, nurse), or according to the laws and
regulations of the country
The training induction is performed by a trained representative of the
manufacturer or a trained representative of the distributor.
• in a home care environment for an adult or patient (maybe a layman)
under control of the facility
The Biomag®Lumina must not be handled by children and other unautho-
rized and uninstructed persons.
Profile of trained instructor
(who can provide the training)
The Biomag®Lumina device induction can be provided:
• an authorised employee of the manufacturer or a written represen-
tative of the manufacturer (eg distributor)
The record of the training can be part of the purchase contract, for additio-
nally trained persons the training is recorded separately.
Patient profile (who can use the device)
The Biomag®Lumina device applies:
• patient older than 3 years
Biomag®devices, like other medical devices, may only be used to posi-
tively affect medical conditions that have been diagnosed by the patient
and have been qualified to avoid contraindications (listed on page 5).
WARNING
Biomag®products must not be used for any other purpose and by
persons other than those described in this chapter or in any other
way than described in this manual.
The manufacturer is not responsible for any damage. The risk is
borne by the user.
1. INTRODUCTION  BASIC INFORMATION

4| page Usermanual
BEFORE USE, PLEASE STUDY THIS MANUAL CARE-
FULLY!
1 | The device may only be manipulated and operated by persons
who comply with the Operator Profile and follow these instructions
when in use.
2 | Therefore, read the User Manual carefully before the first use
of the device!
3 | The system should be put into operation according to the information
provided in this manual.
4 | Any modifications or interventions to the system and applicators
are forbidden.
5 | To reduce the risk of electric shock, this appliance may be capable
of satisfactory electrical distribution.
If in doubt, the grid should be inspected by a safety inspector.
6 | Never use the device or applicators if they are damaged.
7 | Do not pull the applicator out of the device connector while
the application program is running.
Always end the program first, using the button [4] or wait
until the end of the application.
8 | Do not connect anything other than the product manufacturer’s
application to the connectors on the unit (see pages 22 - 23).
WARNING – DO NOT LOOK into the flashing LEDs during
the use of the AL16-LUM (Alfa) applicator and operation
of the polarised light!
9 | Do not pull the power cord of the applicator or unit.
10 | Portable and mobile high-frequency communication devices may
impact the function of the Biomag®Lumina system.
No wireless communication system should be operated within a 3.3 m
distance, it might impact the function of the Biomag®Lumina system.
11 | WARNING – The Biomag®Lumina may cause radio interference
or may interrupt the operation of a nearby device located
next to or in a block with other devices.
It may be necessary to take measures to mitigate these effects,
e.g. to change the orientation or move the Biomag®Lumina system.
During application, the applicators may damage devices
in their immediate vicinity, e.g. watch, magnetic media
(data media, computers, credit cards), etc.
A distance of 1 metre from the applicator is safe.
12 | Avoid any contact of the device with water, do not rinse
or wash it with water.
Never use it in a wet environment (while bathing, in a sauna, etc.).
Never expose the device or the applicators to dampness.
13 | Avoid dropping and any damage to the device and applicators,
utmost care should be taken of the unit connectors and applicators.
Do not place the device near sources of heat.
14 | During therapeutic applications of the Biomag Lumina system,
all national legal regulations and provisions must be adhered to.
15 | The manufacturer is not responsible for improper use of the system.
16 | Mode EASY (programs up to 81 Hz) is designed for individual
prevention and rehabilitation provided point 1 and 2 are adhered to
and rules for operation are followed.
17 | Mode CLINIC (programs up to 162 Hz) is designed for healthcare
providers.
18 | When selecting programs, the best rule is first to ease acute pain program
• 1 Painful conditions and then to select a program based on the type
of problems for which the applications are designed.
In case of long-term or combined health problems, it is recommended
to use program 2 • Medical program (use the more detailed information
on page 15).
19 | When setting parameters for program 32 • Individual program follow
the table listing the effects of pulsed magnetic therapy on page 16.
20 | Therapy should not be performed after 9 pm – sleep disorders
may occur.
21 | During application, special attention should be paid to patients
with hypotension (or with a tendency towards it) and hypertension.
22 | During the first application steps, blood pressure may decrease
and lead to potential negative reactions.
23 | If discomfort is experienced, it is recommended, as a precaution,
to discontinue the application.
24 | Do not apply the applicator part (applicator) to damaged skin
(abrasion, bedsores, cuts, etc.), always use a protective layer,
such as a disposable or other hygienic pad, when applying.
If the patient, including the applicators, use the device,
it is necessary to disinfect the applicators before each
use by another patient.
Disinfection and cleaning is described on page 28.
25 | WARNING – Do not wrap the device power cord or the applicator
cables around your neck – due to the risk of strangulation.
26 | WARNING – Any modifications to the system are forbidden.
27 | WARNING – For the system with a lithium battery the battery
function should be checked regularly every month.
28 | WARNING – Avoid touching the displey when holding, moving
or manipulating with the device .
To operate the touch screen, press gently on the screen, preferably
with a rubber end of a pencil.
29 | WARNING – The manufacturer is not responsible for improper use,
especially in violation of the instructions and provisions of this manual.
30 | WARNING – Follow up-to-date and other important user
information and instructions at https://www.biomag-medical.com/info.
________________________________________________________________
Information for healthcare providers
The Biomag®Lumina device requires special precaution related to EMC
and should be put into operation in compliance with information on EMC
specified on page 25 (information on EMC).
Principles of safe operation – Method of use
The Biomag®Lumina device is standardly certified for the European Union market which is above-standard certified within the IEC – CB Certifi-
cate, which governs the use of the Biomag®Lumina device in some countries outside the European Union. In these states, it is also necessary
to follow the applicable legislation of the respective state.

Usermanual page | 5
1• Painful conditions 60 min
Generally, low frequencies affect all painful conditions (including de-
generative, inflammatory and post-traumatic conditions). Do not use
in patients with acute abdominal pain or suspected myocardial infarction,
to avoid masking any clinical symptoms and making early diagnosis
of acute diseases difficult.
Purpose of the applications >To reduce pain, relieve muscle spasms,
support the healing and regeneration process.
2 • Medical program 25 min
This is a versatile program with automatically changing frequency,
from pain-reducing to healing and stimulating applications.
Purpose of the applications >Recommended for long-term chronic
diseases, where it is desirable to reduce pain and stimulate healing
and regeneration. Suitable for long-term maintenance therapy after acute
manifestations of the disease. E.g. joint degenerative and inflammatory
diseases, to improve metabolic exchange in tissues in diabetes, chronic
inflammation of tissues and organs.
3 • Joint arthrosis 45 min
Recommended to reduce pain in patients with degenerative changes
in joint tissues, including bones, cartilage and ligaments.
Purpose of the applications >To reduce pain and support healing
and regenerative processes. To be applied preferably in the acute phase.
When the pain has been reduced, it is recommended to proceed with
long-term applications of the Medical program.
4 • Spine arthrosis (degener. damage of the spine) 30 min
Degenerative changes in the vertebrae and intervertebral discs, with pos-
sible nerve root compression.
Purpose of the applications >To reduce pain, release muscle con-
tractures and achieve better mobility of the spine.
5 • Joint pain 60 min
Pain in the joints and articular capsules due to morphological changes
caused by degenerative and inflammatory processes.
Purpose of the applications >To reduce pain, suppress the inflamma-
tory process, and provide conditions for better regeneration.
6 • Spinal pain 45 min
Pain in the spinal column due to degenerative, inflammatory processes,
and also due to overexertion, unusual movement activities, or cold.
Purpose of the applications >To reduce acute pain, provide relief
from muscle spasms, achieve better spinal mobility, allow further rehabili-
tation and enhance the regeneration process.
7 • Sciatica acute (sciatic nerve pain) 60 min
Nerve root compression in the lumbar and sacral spine, with pain radi-
ating to the lower extremities, intense acute pain and limited mobility.
This often occurs when exposed to cold or physical exertion with the body
in a non-physiological position.
Purpose of the applications >To provide relief from pain and allow
restoration of the physiological anatomy of the spinal column, helping to
eliminate nerve root compression.
The below information on all programs can be viewed in the device using the arrows while the program is running.
Contraindications
The Biomag®Lumina system may not be used with the contraindications listed below.
Failure to observe the contraindications can result in damage to the health of the patient and the operator!
List and descriptions of programs, purpose of application of the Biomag®
magnetic therapy
• Pregnancy
• Pacemaker
• Bleeding conditions
• Menses (bleeding phase)
• Neoplasms
• Serious septic states
• Fever conditions
• Active tuberculosis
• Mycosis at the site of the application
• Paroxysmal nerve diseases
• Hyperthyroidism
• Pain of unknown origin
• Unspecified diagnosis
• Contradiction to a medical procedure determined
by a specialist
• Direct light in the eye
(applies when applying polarized light)
• For metabolic disorders where photo-sensibility
of the skin occurs and the use of photostimulation
preparations
(applicable when applying polarized light)

6| page Usermanual
8 • Compression of nerves (chronic) 25 min
Nerve root compression in the lumbar and sacral spine, with pain radi-
ating to the lower extremities, intense pain and limited mobility. Unlike
the acute form, this is a permanent disorder which may improve or worsen
temporarily. Frequently, this is a result of degenerative changes in the spi-
nal column.
Purpose of the applications >To provide relief from pain, allow fur-
ther recovery of mobility, enhance the regeneration process and maintain
a long-term bearable condition.
9 • Arthritis of joints 25 min
It is an inflammatory joint disease including rheumatoid arthritis, as well as
arthritis related to other diseases such as gout, psoriasis, etc.
Purpose of the applications >To reduce inflammatory symptoms
and relieve pain. To establish better conditions for healing and regen-
eration by stimulating the vascular system and by enhancing blood flow,
oxygen and nutrient supply and elimination of metabolites.
10 • Arthritis of the spine 25 min
Inflammatory diseases in the vertebral column due to rheumatic disease
or other conditions, such as gout, psoriasis, etc.
Purpose of the applications >To suppress inflammatory symptoms,
reduce pain and improve mobility. To establish better conditions for healing
and regeneration by stimulating the vascular system and by enhancing blood
flow, oxygen and nutrient supply and elimination of metabolites.
11 • Bekhterev’s disease 30 min
A specific inflammatory disease of the spinal column associated with
an immune system disorder, characterised by long-term duration
and gradual progression. The disease results in significant mobility limita-
tion and is accompanied by severe pain.
Purpose of the applications >To reduce pain and allow better recovery
of mobility. To suppress inflammatory symptoms and slow down progression
of the disease.
12 • Rheumatism 30 min
An inflammatory disease of joints, joint capsules and other tissues charac-
terised by a significant immune component.
Purpose of the applications >To suppress inflammatory symptoms
and reduce pain. To improve metabolic conditions for healing, regenera-
tion and normal function of the affected tissues.
13 • Endoprotheses 20 min
Conditions with implanted artificial joint or another replacement of dama-
ged tissues. In most cases, metal or plastic implants are used for the
replacement. All the metal components are made of non-magnetic metal,
so the low-frequency pulsed magnetic therapy can be commonly used
in patients with these conditions.
Purpose of the applications >To provide better metabolic condi-
tions in tissues before and after prosthetic device implantation to improve
the healing process, accelerate the recovery, reduce pain and help maintain
the best possible condition and function of the surrounding tissues.
14 • Post-surgery conditions 20 min
Postoperative conditions require intensive recovery and an increased
metabolic turnover in the affected tissues to accelerate the healing pro-
cess and avoid complications.
Purpose of the applications >By widening the bloodstream, the low-
frequency pulsed magnetic field supplies more oxygen and nutrients
to the blood, therefore aiding the healing process. It also releases and
removes metabolites and harmful substances that hinder the healing pro-
cess.
15 • Fractures 45 min
Treatment of fractures and injuries to bones and cartilages. Therapy should
be started as soon as possible after the injury and surgical treatment.
Purpose of the applications >Low-frequency pulsed magnetic therapy
affects not only the soft tissues but also bone and cartilage tissues, sig-
nificantly supporting and accelerating the healing process, new formation
and restoration of the damaged tissues.
16 • Carpal tunnel 60 min
Carpal tunnel is a syndrome caused by compression of the neurovas-
cular bundle and tendons of the finger flexors in the narrowed channel
of the wrist, resulting in numerous neurological and mobility disorders,
including pain.
Purpose of the applications >To support anti-swelling and anti-infla-
mmatory effects, to provide relief from or elimination of the compression,
and to improve regeneration of the affected tissues.
17 • Tennis elbow 60 min
This includes pain in the elbow joint, called epicondylitis or tennis elbow,
resulting from one-sided overexertion.
Purpose of the applications >To reduce pain and support the healing
process, in addition to other surgical and rehabilitation treatments. Inflam-
matory diseases of the tendons and ligaments tend to become chronic
and recur in case of early exertion or insufficient treatment and recovery.
Therefore, magnetic therapy is recommended for prevention even during
the remission stage.
18 • Postamputation pain 30 min
Post-amputation pain, or phantom pain, is sometimes experienced
in the phantom limb or stump after limb amputation.
Purpose of the applications >To reduce pain and increase the chance
of elimination of these painful sensations.
19 • Prostatitis (prostate inflammation) 20 min
Benign prostatic hypertrophy and inflammation of the prostate are common
diseases in men and their incidence increases with age, usually starting
at around the age of 50. Swelling and inflammatory changes result in impaired
urine flow, with more frequent urination of small amounts of urine.
This condition is not only annoying but also poses a serious risk of devel-
oping malignant prostatic disease.
Purpose of the applications >To use the anti-swelling and anti-inflam-
matory effects of the low-frequency pulsed magnetic therapy for healing
and restoration of normal functions.

Usermanual page | 7
20 • Extremity ischaemia 25 min
(reduced blood flow to extremities)
Damage to blood vessels in the extremities (arteriosclerotic changes and other
causes) results in insufficient supply of oxygen and nutrients to the muscles
and tissues. This leads to many trophic changes that may result in limb amputa-
tion.
Purpose of the applications >Low-frequency pulsed magnetic thera-
py dilates minor capillaries and pre-capillaries, and significantly improves
blood flow and supply of oxygenated blood to the tissues. In this way,
it provides better conditions for normal functioning.
21 • Diabetic foot 20 min
Diabetes may cause diabetic neuropathy and microangiopathy, i.e. damage
to minor arteries that supply oxygen and nutrients to the tissues. Acid
metabolites accumulate in the tissues leading to further progression
of the disease. Trophic changes may result in venous ulcers and amputa-
tion.
Purpose of the applications >To reduce pain and improve blood circu-
lation in the tissues. The therapy supports vascular flow, i.e. blood vessel
dilation – to increase oxygen and nutrient supply to the tissues and release
and remove accumulated acid metabolites. This will increase the chance
of saving the limb while reducing the secondary consequences of the dia-
betes in the vascular system.
22 • Tinnitus 30 min
Tinnitus (murmur or whistling in the ears). This condition is caused by
a dysfunction of a part of the inner ear, mostly due to ischaeamic vascular
changes.
Purpose of the applications >The goal of magnetic therapy is to influ-
ence the vascular system and improve oxygen and nutrient supply, and to
try to preserve the function of the hair cells in the inner ear, which leads
to normalisation of functional pathological manifestations, and minimises
further permanent damage.
23 • Venous ulcer 15 min
Venous ulceration is disintegration of the superficial tissues of limbs due
to vascular changes in the lower extremities.
Purpose of the applications >To support healing regenerative pro-
cesses and create the best possible conditions for healing of the lesion
and improved viability of the affected tissues.
24 • Brain dysfunction (children and adults) 25 min
Minimal brain dysfunction in children is a disorder of the central nervous
system in children. It is developed during intrauterine life, due to birth
trauma, ischaemia and many other factors. The extent of damage deter-
mines a wide range of pathological manifestations, from mobility disorders
to impaired concentration, learning, etc. The basis of therapy is targeted
for long-term rehabilitation.
Brain dysfunction in adults is usually related to insufficient vascular supply
of the brain and degenerative changes due to ischaemic, autoimmune,
toxic, and other changes.
Purpose of the applications >Pulsed magnetic therapy is a suitable
physiotherapeutic method, leading to muscle tone adjustment, improve-
ment and better repair. Remarkable effects have been described in sci-
entific literature even in children with severe musculoskeletal dysfunction.
In adults, low-frequency pulsed magnetic therapy is intended to improve
oxygen and nutrient supply to create better conditions for preservation of
the brain’s functions.
25 • Polyneuropathy 25 min
Polyneuropathy is a diverse group of disorders related to the peripheral
nerves. Usually, this is a systemic process with involvement of multiple
nerves, resulting from various internal and external causes (such as inflam-
mation, metabolic, immunopathogenic mechanisms, toxic factors, nutri-
tional and vitamin deficiency, degenerative causes, etc.). The usual symp-
toms include tingling, burning, pain, reduced sensitivity, uncertain walking,
muscle weakness, aches and spasms, and many other symptoms.
Purpose of the applications >Magnetic therapy is the optimal sup-
portive method for all types of polyneuropathy. It modifies the immune
system and its responses, has anti-inflammatory effects, reduces pain,
improves blood circulation and metabolism in tissues, improves oxygen
supply to the tissues and supports regeneration.
26 • Periodontal disease 45 min
Periodontitis is chronic inflammation and damage to the periodontium,
i.e. the tissues that surround and support the teeth. The very first symp-
toms are swelling and reddening of the gums, bleeding, painful sensa-
tions when cleaning teeth, and halitosis.
Purpose of the applications >Stimulation of tissues by low-frequen-
cy pulsed magnetic field significantly improves blood oxygen supply
to the affected gums to support the healing process, eliminate swelling,
suppress inflammation, and reduce pain. Magnetic therapy is an effective
complement to dental care.
27 • Muscle fatigue 30 min
Muscle fatigue after exercise, heavy physical work and when exhausted.
Purpose of the applications >To reduce pain and create metabolic
conditions to accelerate muscle recovery.
28 • Regeneration 25 min
Regeneration after physical work and sport, targeted preparation for in-
tended demanding activities.
Purpose of the applications >To accelerate the recovery process and
restore energy reserve in muscles by improving blood oxygen and nutrient
supply and removing acid metabolites. This will help create optimal condi-
tions for the next demanding physical activity.
29 • Before massage 20 min
A 20-minute preparation before a massage session and before the use
of manipulation procedures.
Purpose of the applications >To enhance blood circulation in tissues,
release and remove acid metabolites, relax muscle spasms and contrac-
tures and provide optimal preparation for the massage session so that
the final effect is much greater and stronger.
30 • Relaxation 45 min
The application is intended for individuals who need to achieve intensive
relaxation. Recommended after increased physical and mental exertion
and in those suffering from psychological stress.
Purpose of the applications >To achieve calming and overall relaxa-
tion of the blood circulation and nervous system.

8| page Usermanual
31 • Magnetisation of water 20 min
(metabolic disorders)
The low-frequency pulsed magnetic field may be used to treat drinking
water and/or foods with a high water content (drinks, fruits, etc.).
Purpose of the applications >By affecting the inner structure and bonds
of water molecules, water is activated and the bonding capability of water
as a solvent is increased, stimulating all metabolic processes in the body.
32 • Individual program 5-120 min
Factory setting: frequency 50 Hz, wobbling 10 Hz, program type rotary,
wobbling type pulse by pulse + rectangle, intensity 100%, duration 30 min.
Program which enables custom setting of parameters for the applications:
frequency, frequency wobbling, application type, wobbling type, pulse
profile, intensity and time.
For setting the Program INDIVIDUAL, refer to the table of prevailing thera-
peutic effects and other information specified on page 16.
Purpose of the applications >Allows the user to enter their own set-
ting of the program and find the best frequency range with optimised
parameters.
Automatic program repeat
max. 4x 2 h = 8 h + time of the last repeat
Allows to repeat the selected program 4 times in a row.
Each repeat is started 2 hours after the beginning of the program
application.
For example, program 3 • Joint arthrosis 45 min
First application 45 minutes, then 1 hour 15 minutes pause, second
application 45 minutes and again 1 hour 15 minutes pause, etc.
Purpose of the applications >Allows the user to enter their own set-
ting of the program and find the best frequency range with optimised
parameters.
Other applications of magnetic therapy can be found in professional
literature (brief list - see page 30).
Cellulite
Cellulite starts at an early age, especially in overweight people, in certain
vulnerable areas of the body, in connection with malfunction of the vas-
cular and lymph skin circulation and insufficient removal of metabolites
and toxic substances from these areas. This results in changes in the liga-
ment and subcutaneous adipose tissue which are enlarged, hypertrophic
and stiff, which leads to unsightly, “orange peel” skin.
The healing method is derived from the cause of the disease. The aim is to
improve the vascular and lymph circulation, improve the supply of oxygen-
ated blood, enhance metabolite and toxic substance removal, and reduce
excessive subcutaneous adipose tissue.
Purpose of the applications >Low-frequencypulsedmagnetictherapy,
due to the significant vasodilatation, anti-swelling, counter-inflammatory
and detoxification effects – supports other healing procedures and motor
activities (lymph drainage, stabilisation of weak ligaments, diet and exercise
procedures, medical cosmetics, etc.), which results in higher efficiency
of the healing process. The applications can be made even more effective
by combining magnetic therapy and polarised light.
Properly functioning vascular and lymphatic systems require sufficient
intake of liquids – the basic condition of any detoxification process.
Magnetic therapy should be applied every day, repeatedly, on the affected
parts of the body.
It is recommended to use program 28 • Regeneration preferably twice
in a row at least once daily.
In addition to the programs above, magnetic therapy is also used in health-
care practice for its beneficial effects on other health problems. The most
frequent conditions are pre-set in the Biomag®Lumina CLINIC system.
(see the table providing a list of conditions – on page 19).
Frequency Wobbling/type Intensity/pulse shape Time
User's records of the Program INDIVIDUAL settings

Usermanual page | 9
a) Device description
At the top and bottom back, there are holes
for attachment of fixation strap
At the back - system restart
pinhole
2. DEVICE CONTROL
8–11 LEDs indicating the applicators are connected to single outputs 1–4
13–16 Outputs (connectors) for connection of applicators
(connector 1 – connector 4)
12 Connector for power cord
1Graphic information display
2Button UP
3Button for displaying the list of all
installed programs
TIME – Time setting for simplified
mode devices
4Confirmation button START/STOP
5Button for displaying the MY
PROGRAMS list
INTENSITY – Magnetic field intensity
setting for simplified mode devices
6Button DOWN
7LED
indicating connection to power supply
(lights permanently)
and battery recharging (flashes)
Notice:
If your device is set to mode EXTRA, only buttons
and can be used until a selected program starts
running.

10 | page Usermanual
1 | Connect the device to the socket using the power
cord *
The device displays identification data and then the program that was
used last time.
2 | Connect 1 to 4 selected applicators **
The outputs for the applicators are at the bottom of the device. (13 to 16).
Apply the applicators conveniently to the affected areas of the body.
3 | Program selection
If the selected program suits you, go to step 4.
You may select another program using the following steps:
Use the button (3) to display the list of all programs.
Use the button (5) to display the most frequently used / favourite pro-
grams .
Use the buttons (2 and 6) to select the required program. ***
4 | Starting the program
Use the button (4) to start the program. ****
The application will start runnig.
After 6 minutes, the display switches over to the energy-saving mode.
5 | Switching off the system
First, use the button (4) to stop the running program.
Hold the button (4) for the period of 6 beeps and confirm by "YES"
to switch off the system.
The system automatically turns off after 6 minutes of idling.
Notes
* If a charged battery is part of the device (the battery is recharged eve-
ry time the system is connected to the electrical socket), applications
can be performed in the same manner as with the system connected
to the electrical grid.
Due to reduced power of the system when powered from a battery,
the application time is automatically prolonged by 30 %. For example,
1 hour of operation when powered from the electrical socket = 1 hour 20
minutes of operation when powered from a battery.
** The double connectors (2C) and triple connectors (3D) are properly
plugged in if the connector side with the Biomag®logo is facing
upwards .
*** In the CLINIC mode, you can repeatedly press the button to search
for programs by entering the program number right on the display.
**** In the CLINIC mode, you can press the round button (4)
to display the screen with options for the application time adjust-
ment. Use the arrows (2 and 6) to change the application time.
Press the button (4) repeately to display the screen with options
for intensity adjustment. Use the arrows (2 and 6) to change
the intensity. Press the button (4) to start application.
***** EXTRA mode screen - simplified mode Finest Top. For devices
in mode EXTRA you can set the time and intensity .
Tips
• You can interrupt the program at any time by briefly pressing the
button (4).
• You can resume the application by pressing the round button (4)
again.
• The program ends after the time displayed on the screen has lapsed.
• By selecting program 32 • Individual program you can adjust param-
eters of the program.
• Hold the button (4) for 3 beeps to start automatic program repeat
(if the automatic repeat is available in the program ).
• If you want to set other features of the system, follow the instruc-
tion on the display by selecting the "Next menu" item. Display the
screen with the "Next menu" item before starting the application,
or from the suspended program from both lists of the programs
by double-clicking the round button (4). To proceed, select the item
using the arrows (2 and 6) and press the button (4).
• You can quickly copy programs from the list of all programs, rename
them and remove the unused programs from the list of your own pro-
grams.
Triple click the button to display the menu for copying and renam
ing programs.
Triple click the button to display the menu for removing a program.
• Other possible system settings are described on pages 12–13.
Parallel run of another program
• The system may be equipped (as an option) with the function for inde-
pendent running of 2 programs, i.e. for outputs 1, 2, 3 and separately for
output 4 (3/1), or for outputs 1, 2 and separately for outputs 3, 4 (2/2).
• The function of a separate run of the right output / right outputs is done
after starting the application on the left outputs by triple clicking the
button (4). You will know you have entered the program selection for the
right outputs by the purple colour of fonts. In this "purple zone" you can
select, start and suspend a second program.
• During the application you can display information on the running
programs on the left and right outputs / right output by double clicking
the button (4).
This quick start is intended for easy orientation. Use it only after you have been provided with professional training and have
completely studied the User Manual. Always follow the safe operation rules (page 4) and the contraindications (page 5).
For the magnetic therapy application, at least one applicator must be connected to the device. You are recommended
to use two applicators at a time (the first to the causative area of the problems and the latter to the affected part of the body).
The system can run in the EASY or CLINIC modes. Before starting the program, double click the round button (4)
to display the set mode.
b) Basic operation – quick start
Brief instructions for the Biomag®Lumina device operation

Usermanual page | 11
Explanations
The bottom part of the device includes LEDs (1 green, 4 blue) indicating certain states of the device. If the green LED is lit permanently, the system is
connected to electrical grid. Flashing green LED indicates recharging of the battery (when the battery is fully charged the LED stops flashing).
Blue LEDs light permanently (when applicators are connected). When the blue LED flashes or is not lit (when applicators are connected), it indicates
a fault of the applicator (see page 29).
under this button, the following are displayed by default: 1 most frequently used program and 8 copied programs from the list of all programs .
The user can order expansion of own programs from the seller. Parameters of programs cannot be changed in the MY PROGRAMS list.
Biomag®Lumina is equipped with effective applicators, including applicators with rotary pulsed magnetic fi eld, and a special applicator combining
pulsed magnetic fi eld with polarised light.
32 rotary
3D
programs are activated in the basic equipment of the device.
It is possible to order applicators and possibly other equipment according to the user’s request.
The device is connected to the mains
(not necessary for battery operation)
and is placed on a stable surface within
reach of the patient’s application position.
Selected applicators are properly
connected to the device.
The device is turned on, and the patient
has an application program selected.
The patient has the attached applications
applied to the place or location of the
application and takes a pleasant journey
(lying down or sitting).
The patient is dressed or has a disposable
or other sanitary pad inserted between
the applicator and the applied body part.
Example of proper connection of the Biomag®Lumina system before starting
the application
The operator, user or patient is familiar with the rules of safe operation and instruction guide and follows them.
Applications will be administered to the patient, or the patient will administer applications by themselves
only if conditions in article „Patient profile (who can use the device)” on page 3 are met.
Contraindications must be ruled out by a professional before application.

12 | page Usermanual
c) Operation of the Biomag®Lumina system
and other possible settings
To display program details, double click the button
on any program from the list of all programs
or from MY PROGRAMS .

Usermanual page | 13
Touch the display to select your own name and use the round
button to save it.
• Key combinations
Press the and buttons simultaneously to display
the screen to enter the code (when other functions of the system
were bought.).
Press the buttons simultaneously to display the screen
with information necessary for your communication with
the service centre.
• How to rename programs
Back

14 | page Usermanual
Based on the Intended purpose listed on page 3, the Biomag®Lumina is
used for pulsed magnetic field applications.
Applications are recommended especially for musculoskeletal problems,
vascular insufficiency and a wide range of degenerative diseases.
Recommended number of applications
Twice a day, in more severe cases the application can be carried out on
average 3 or more times a day, usually for at least two weeks, for chronic
conditions significantly longer.
The preset times for the individual programs are the minimum recom-
mended time for inducing the respective effect and can be extended up
to 120 minutes.
The maximum number of applications and the maximum recommended
application time is not specified, and according to the doctor’s recom-
mendation, applications can be repeated and for a long time.
Mechanism of effects (principle of biological action)
Magnetic therapy is based on the influence of an artificial magnetic field
of certain parameters on the human body. It is a physical therapy which
generates large-area pulsed magnetic field of low frequency. Pulsed mag-
netic field acts on the cell membrane permeability, i.e. it improves and ac-
celerates metabolism. Blood circulation and oxygen supply is significantly
better in the part of the body to which the pulsed magnetic field is applied.
Increased metabolic turnover and improved supply of exposed tissues
with oxygenated blood and nutrients provide optimal conditions for healing
and regeneration. The magnetic field traverses the entire organism and
thus acts on each cell (to achieve the Intended purpose). The effectiveness
of therapy applications is individual, and independent sources report an
average of up to 70% effectiveness when used appropriately.
Range of possible use
The Biomag®Lumina can be used to alleviate problems wherever the
cause of these problems can be positively influenced by inducing the ef-
fects of LPMF below. The effects of Biomag®applications can be used
in all medical fields.
Effects of low-frequency
pulsed magnetic field
Biological changes in the tissues resulting from the effects of low-
frequency pulsed magnetic field can be beneficially used in a number
of health problems. The effects can be summarised in six treatment
groups and effects:
• pain-relieving (analgesic)
• myo-relaxing (relief from spasms)
• anti-swelling (anti-oedema)
• vasodilating (widening the bloodstream)
• metabolic-detoxifying (degrading pollutants)
• healing (with support of regeneration, anti-inflammatory
and anti-rheumatic)
Frequencies inducing preferable therapeutic effects are described
and provided graphically in the table on page 16.
Pan-relieving effect
Due to magnetic induction, the LPMF stimulates generation of current
in nerve fibres, which blocks painful sensations moving from the pain
source via the spinal cord to the brain centres, and as a result of this
and some other mechanisms (enhanced endorphin production, suppres-
sion of inflammation and swelling, myo-relaxation), it leads to pain relief.
Increased production of endorphins and control of calcium ion transfer
across the cell membrane also helps to achieve vasodilation, and anal-
gesic and calming effects. After application of LPMF, increased activity
of lactate dehydrogenase (required for removal of lactic acid which stimu-
lates nerve receptors and causes pain) has been demonstrated in exposed
muscles. Especially good pain-relieving results with the Biomag®system
have been proven in radicular (root) and pseudoradicular syndromes (sci-
atica, compression of nerves for various reasons). The analgesic effect
is the basic effect, for which magnetic therapy is used in most people.
It can be widely used in a whole range of degenerative diseases of the
musculoskeletal system, post-traumatic and postoperative conditions.
Myo-relaxing effect
Relaxing skeletal muscles. Low-frequency pulsed therapy is used to re-
move acid metabolites faster (due to enhanced perfusion and improved
activity of lactate-dehydrogenase), which results in relief from painful
irritation in muscles and in the sites of chronic inflammation. This reduces
pain and relieves painful muscle spasms (contractions). Magnetic ther-
apy has also demonstrated significant deceleration of nerve conduction
in the lower extremities of athletes – this effect also contributes to myo-
relaxation (muscle relaxation). The myo-relaxing effect of the Biomag®
system on the back muscles (para-vertebral striated musculature around
the spinal column) brings relief from many problems, e.g. stiff cervical
spine, headache, dizziness, impaired hearing, limited mobility, pain that
spreads from the spine to the extremities, etc.
The myo-relaxing effect on the muscles brings relief during colic and re-
laxation of the skeletal muscles is necessary in the treatment of any painful
conditions of the musculoskeletal system.
Anti-swelling effect
Of accelerated metabolism after the LPMF application enables faster
re-absorption of swelling and provides significant anti-inflammatory
and analgesic effects in the affected area. Position the Biomag®system
applicators over the affected area (e.g. in the case of an ankle sprain)
and repeatedly perform 30-minute to 45-minute stimulations three times
daily to achieve significant relief from swelling and pain. Anti-swelling
and anti-inflammatory effects can also be used successfully for upper
respiratory tract infections, sinusitis, inflammation of the gums, in allergic
rhinitis, etc.
Vasodilating effect
LPMF affects the polarization of red blood cells by positive charge. It acts
against the stacking (coin-roll formation) of red blood cells as it causes
their re-dispersion, thereby increasing the surface area capable of binding
and carrying oxygen. Blood which has passed through a magnetic field
has a higher ability to bind oxygen (it is easier to oxidise). Polarisation
of red blood cells improves the muscle tone of blood vessels, arter-
ies and capillaries – causing their dilation (vasodilation) and enhancing
the supply of oxygenated blood and nutrients to the tissues and faster
removal of toxic substances out of the cells. The partial oxygen pressure
is significantly increased. The LPMF acts positively on erythrocyte plastic-
ity. More flexible blood cells can better adapt to "obstacles" in the vas-
3. APPLICATION

Usermanual page | 15
culature. LPMF also reduces the risk of blood clots (thrombi). Low-fre-
quency pulsed magnetic therapy activates the parasympathetic nervous
system and promotes the efflux of Ca2+ ions, which leads to relaxation
of the blood vessel muscles (particularly pre-capillary sphincters)
and to subsequent vasodilation. All this contributes to harmonisation
of the heartbeat, circulation and blood pressure. LPMF has proven suc-
cessful, mainly in mild forms of ischaemic heart disease, but also in lower
and upper limb ischaemia, non-healing lower leg ulcers, and in all perfu-
sion disorders. No recanalisation of already obstructed vessels occurs,
but the collateral circulation in the skin and muscle tissues is greatly
dilated.
Vasodilation is desired in any vascular system disorders where the oxy-
genated blood flow is impaired, i.e. in ischaemic disorders of the extremi-
ties, heart or brain, all cases where a better supply of oxygen helps healing
and improving the function of the tissues and organs and also provides
anti-inflammatory effects.
Metabolic-detoxifying effect
Stimulation of metabolism. LPMF passes evenly through the exposed tis-
sues, i.e. through every cell, inducing weak electrical currents there. This
leads to changes in the surface potentials of the cells, changes in cellular
membrane permeability, increased blood circulation, improved oxygena-
tion, nutrient supply and better removal of metabolic waste from the ex-
posed tissues, which are the basic requirements for any healing process.
Enhanced metabolism, removal of waste products and detoxification
initiate any healing and regenerative process. For example, exposition
of the liver using the Biomag®system stimulates liver function, and ac-
celerates and enhances detoxification processes in the whole body.
Local effects are achieved by placing the applicator on the affected area
– e.g. muscle, joint, spine, etc. By using a small applicator, we can achieve
strongerlocaleffectsduetoahigherinduction,whiletheuseoftheapplicator
with a larger application area results in a greater positive whole-body
metabolic effect despite the lower induction.
This effect leads to improvement in many diseases and conditions,
e.g. diabetes, gout, regeneration of tissues after infections (hepatitis,
mononucleosis, toxic destruction of tissues, etc.), and also in eczema
and allergies.
Healing effect
Has been demonstrated for bones and soft tissues, and it is explained
by a nonspecific irritation of the cytoplasmic membrane, which leads
to the activation of the metabolic chain, where the key point is the alteration
of the cAMP/cGMP ratio and increased activation of osteoclasts during
bone healing. LPMF significantly accelerates the healing process, activates
the formation of new tissue (rapid building of bone tissue and calcification)
and leads to increased sensitivity to the parathyroid hormone. Therefore,
low-frequency pulsed magnetic field is used to accelerate the healing
of fractures, pseudo-arthrosis (false joint), and for the reinforcement
of loose and painful endo-prostheses. The LPMF application increases
the level of proteoglycans in cartilage by up to 22%, which allows healing
and regeneration of cartilage that is otherwise difficult and influenced only
to a limited extent. Accelerated wound healing has been demonstrated
not only in blood, but also in soft tissue. The Biomag®series systems
have a positive effect on both sterile (rheumatoid diseases) and microbial
inflammations and their healing. They induce increased phagocytic
activity, including production of superoxide, which inhibits microbial
flora, but can also be a source of temporary impairment, such as in patients
with rheumatism during the first applications. Subsequent activation
of superoxide dismutase leads to alleviation of symptoms and onset
of healing changes. Especially good results are achieved in the radicular
and pseudo-radicular syndromes (sciatica, nerve oppression of various
origin). This effect is a complex of other partial effects and it supports the
natural ability of the human body to heal and regenerate.
Characteristics of the low-frequency pulsed
magnetic field and frequency range used
in the Biomag systems
Polarity of applicators
Pulse of one polarity generated by the Biomag®systems allows the ap-
plicators to always have the same polarity at a certain area (applicator
polarity and its identification are described on page 21).
Frequency low-frequency pulsed magnetic field
Low frequency: 1 to 10 Hz
Pain-relieving and myo-relaxing effects prevail.
Medium frequency: 10 to 15 Hz
Anti-rotational effects prevail, suitable for chronic and degenerative disea-
ses. They have both pain and vasodilatory effects, inflammation, improve
blood flow and sap flow.
Higher frequency: up to 25 Hz
Stimulating effects prevail which support bone healing, improve post-
traumatic conditions and burns, stimulate healing process during acute
disease. It has a detoxifying and healing effect, to a lesser extent also
analgesic and anti-inflammatory.
Frequencies: above 25 Hz (26 to 162 Hz)
Used when we need to increase the intensity of the LPMF effects,
or for certain types of health problems such as burns, difficult fracture
healing, and pseudoarthrosis. Intended for more intensive stimulation of
the healing process, regeneration, and detoxification.
Every authorised seller is able to put you in contact with specialists
that provide professional consultancy.
Selection
and use of the applicators
From the applicators available (see below), always select the type that
best suits the particular therapeutic purpose, and place it as close
to the surface of the treated part of the body as possible. Some applicators
can be fixed to the affected part of the body with an elastic strap. Most
of the others allow fixation on the body using optional accessories.
It is good to use it if necessary because precise positioning of the applicator
increases the application process efficiency (for solenoids generating the
spatial pulsed magnetic field, it is sufficient just to insert the treated part
of the body into the inner space of the solenoid). When assessing the suit-
ability of individual applicators, we focus on ensuring that the applicator
is placed comfortably on the body as close as possible to the affected
area, and whether or not in-depth solenoid therapy with an applicator
is needed or a flat applicator is sufficient.
In both modes (EASY and CLINIC) in programs marked with the
symbol, it is convenient to use the applicator with a triple-connector (page 10),
which turns on the individual components of the applicator gradually
and guarantees that when the applicator components are assembled,
or get close to each other, the magnetic field intensity is not reduced.
It also provides better penetration of magnetic field into the treated part
of the body, which improves the efficiency of the application.
®

16 | page Usermanual
Brief instructions for settings based on required therapeutic effects
For setting pulse shape, LPMF intensity and frequency modulation use program 32 • Program Individual and set the required parameters.
The table shows prevailing therapeutic effects based on frequencies (guide for the Program INDIVIDUAL).
dark field = the most effective frequency range for a given treatment effect
bright field = frequency range for a given therapeutic effect with a less significant effect
The following description is focused on the choice of frequency and
other LPMF parameters by therapeutic effects. It is used for the Pro-
gram INDIVIDUAL. Therapeutic effects are provided on page 14–15.
For easier setup you can also select the option of preset parameters
for each program (description of simple setup procedure is provided
on page 10, for a list of preset programs, see pages 5–8 and 18–20).
Knowledge of the cause of the problems is a critical requirement for
the application (Patient profile, page 3). It determines the frequency
that is to deliver the desired effect. To provide benefits in a number of
medical conditions and disorders, it is suitable to use more effects,
in a successive or alternate manner.
For example, problems with severe pain will be addressed first by using
frequencies inducing analgesic effect, and after remission of the acute
pain, frequencies inducing healing or other desired final effects should
be used.
Pulse profile, intensity of LPMF and frequency modulation (wobbling)
The program INDIVIDUAL indicates pulse profile for each frequency
and intensity. A sharp pulse profile has a stimulating effect (PIKE, TRI-
ANGLE) while other profiles (ROUNDED=SINUS, RECTANGULAR)
have pain-soothing effects and relax spasms. Modulation of frequencies
in three-minute sequences provides the desired effect in a smooth man-
ner. Modulation of frequency after a pulse provokes more pronounced
response of the body. These facts should therefore be taken into consid-
eration when choosing the right application.
In this manual, we mainly describe and recommend the program frequen-
cy range of 1-81 Hz. Frequencies above 81 Hz (designed for special
applications) are used for certain types of disabilities, such as burns,
poorly healing fractures and pseudo-arthrosis. In cases where the cause
of local pain is somewhere else, we recommend applying pulsed mag-
netic field using two applicators at both sites simultaneously.
Each effect and the use of magnetic therapy should be judged
by the specific condition and response of each patient. In the event
of an unexpected reaction, stop the application immediately! The ap-
plication should not be resumed unless checked by the specialist
doctor based on the procedure specified by them.
When magnetic therapy is used as part of treatment, some people may
expect a slight temporary increase in sensitivity. This is a so-called spa
syndrome and is frequently followed by a significant improvement. You
are advised not to stop the application, but only to reduce the application
intensity for 2-5 days.
Frequencies in Hz
Prevailing
therapeutic
effect
Pain-relieving
Myo-relaxing
Anti-swelling
Vasodilating
Metabolic-detoxifying
Healing
Brief plan of the low-frequency
pulsed magnetic field application
C

Usermanual page | 17
The Biomag®Lumina electronic system is a modern system for the ap-
plication of pulsed magnetic fields of low frequency which have a positive
regenerative effect on human health boosting the immune system. Ope-
ration of the system is very easy. There is indication of states, including
failures. Some states are indicated by audio signals.
In the EASY mode (for home care), the system offers 32 programs
with the frequency range of 1 to 81 Hz, and in the CLINIC mode
(for healthcare providers), there are 108 programs with the frequency range
of 1 to 162 Hz. The system generates pulses of one polarity and has
10 time ranges of time, five levels of output power, four outputs
and it is relatively powerful despite its very small size. The components
of the device and the applicator are tested at a test voltage of 4000 V
which guarantees absolutely safe operation.
Biomag®Lumina is a portable magnetic therapeutic system designed for
non-continuous operation. The application is ended when the selected
program has finished. All indicators and controls are on the front panel of
the device.
At the bottom of the front part of the device there are 4 connectors for the
applicators and a connector for the power cord. The back side includes
a label with identification data of the system and the manufacturer, and
the bottom part includes the serial number and the system restart pinhole.
Disconnection of the system from power supply is done either by pull-
ing the power cord from the device (the power cord connector is shown
on page 10 in the description of the system and its controls), or by pulling
out the power cord plug from the electrical socket.
Specifications of the system are provided in Table 1 on page 18, software
is specified in Tables 2 and 3 on pages 18–20.
Other Biomag®models are based on the technical solution and param-
eters of the Biomag®Lumina.
4. TECHNICAL SPECIFICATIONS
When and how often to apply
low-frequency pulsed magnetic field
In general, the application time of magnetic therapy should be different
for different cases, sometimes also repeatedly in long cycles. Where it is
possible, do not stop magnetic therapy suddenly, but at the end lengthen
the intervals between applications.
We recommend that patients with low blood pressure should rest for
about 20 minutes after the application. The recommended number of ap-
plications for short-term difficulties is 20 to 30, but at least 10 applica-
tions. Long-term repeated applications are recommended particularly for
chronic conditions and aftercare.
If there is a slight impairment in the course of day 1 – 5 of the treatment,
it is a well-known process in the initial reactive phase and it is not a reason
for discontinuing the treatment. The pain usually disappears during the
following applications and is followed by significant improvement.
If there is no reaction to treatment within 5 – 6 applications, there is
a resistance to therapy. In such cases the effects may appear with 15–20
applications.
Minimum application time is 20 minutes, the minimum number of applica-
tions is 10 while the optimum number is 15-20, in severe cases even more.
Pulsed magnetic field may affect functional disorders, although not fixed
pathological changes. Biomag®low-frequency therapy is not addictive,
meets all safety standards and uses an entirely user-safe method.
Before using the system, you should first consider all contraindica-
tions!
Further information for low-frequency
pulsed magnetic field applications
Physiological mechanisms of the magnetic therapy act on the systemic,
organ, tissue, cellular and molecular levels.
Magnetic therapy may accelerate the remission of problems in painful
conditions of vertebrogenic or muscle origin, during inflammatory con-
ditions of nerves, muscles, tendons and bones, in the treatment of joint
swellings, arthrosis, while also accelerating the healing of bone fractures,
improving blood circulation in the affected areas, etc. In most cases,
the patient does not perceive any sensation during the application.
The Biomag®tester is used to check the pulsed magnetic field.
Magnetic field penetrates all parts of the body, bones and tissues equally,
the patient does not need to undress and even plaster casts are not
a problem.
Metal implants are not contraindicated for the low-frequency pulsed mag-
netic therapy.
The patient takes a comfortable position (sitting or lying down) before start-
ing therapy.
Attach the applicator close to the surface of the body area that is to be
treated, or the painful area.
If possible, the first five applications should be performed on successive
days.
a) Technical description and specifications of the system

18 | page Usermanual
Table No. 2: Biomag®Lumina software
Table No. 1: Technical specifications of the system
*
Description Values
Power supply voltage ~100 to 240 V, 50/60 Hz
Input power max. 60 VA
Voltage of integrated power source 24 V =
Device insulation class II.
Applied part type BF type
Environment normal
Protection class IP 30*
MIMF max. 51 mT
Output regulation (intensity) EASY
10 levels
CLINIC
12 levels
Number of outputs for applicators 4
Number of the EASY programs 31 programs
+ Program INDIVIDUAL, 1 to 81 Hz
Standard number of programs in MY PROGRAMS for the version EASY 1 most frequently used + 8 customised programs
Number of the CLINIC programs 107 programs
+ Program INDIVIDUAL, 1 to 162 Hz
Standard number of programs in MY PROGRAMS for the version CLINIC 1 most frequently used + 65 customised programs
Program frequencies EASY CLINIC
from 1 to 81 Hz from 1 to 162 Hz
Pulse profile to be selected from the menu pulse: pike, triangular, rounded, rectangular
Pulse leading edge width (is dependent on the selected program and applicator induction) 0.4–2.5 ms
Pulse width 1.1–11.1 ms**
Pulse descending edge depending on the applicator induction 0.5–3.5 ms
Number of time ranges 10
Application times 5, 10, 15, 20, 25, 30, 45, 60, 90 and 120 min
End of application audio alarm + display
Warning messages audio indication + display
EMC – electromagnetic compatibility CSN EN 60601-1-2 ed.3:2016
Ambient temperature around the device +5°C to +35 °C
Dimensions 240 x 162 x 75 mm
Device weight 0.845 kg
Battery (if included in the system) – type LIP745690P/2S
Battery weight 165g
Operation time when powered from battery (with 4 outputs occupied) approx. 160 min
Battery recharging time 7 hours
*IP 3 – protected from penetration by solid objects of 2.5mm size and larger; IP 0 – not protected against water
** changes between three levels based on the program, to induce maximum cell response
In the EASY mode, only frequencies up to 81 Hz are used.
Program No. List of programs – health conditions Time (min)DF EASY intensity (%) CLINIC intensity (%) EASY frequency CLINIC frequency
1Pain 60 80 80 6 + 4, 5, 6 Hz
2Medical program 25 80 100 2–25 Hz
3Arthroses joints 45 80 90 4–10 and 2–25 Hz 4–10 and 10–50 Hz
4Arthroses spine 30 80 90 4–10 and 2–25 Hz 4–10 and 10–50 Hz
5Joint pain 60 80 100 4–10 and 2–25 Hz 4–10 and 10–50 Hz
6Spinal pain 45 80 90 4–10 and 2–25 Hz 4–10 and 10–50 Hz
7Sciatica acute 60 80 100 4–6 Hz
8Compression of nerves 25 80 100 13–17 Hz
9Arthritis of joints 25 70 70 2–4 and 2–25 Hz
10 Arthritis of spine 25 70 70 2–4 and 2–25 Hz
11 Bekhterev’s disease 30 80 80 2–4 and 2–25 Hz
12 Rheumatism 30 80 90 2–25 and 8–20 Hz
13 Endoprostheses 20 80 80 8–12 Hz
14 Post-surgery conditions 20 80 100 9–11 Hz
15 Fractures 45 80 100 21–25 Hz 30–36 Hz
16 Carpal tunnel 60 80 90 4–10 and 2–25 Hz
17 Tennis elbow 60 80 80 4–10 and 2–25 Hz
18 Postamputation pain 30 50 50 2, 5, 10, 12, 15, 20, 25 Hz
19 Prostatitis 20 80 100 21–25 and 2–25 Hz
20 Extremity ischaemia 25 80 100 22–25 Hz 36–44 Hz
21 Diabetic foot 20 50 50 20–25 Hz 44–56 Hz
22 Tinnitus 30 80 90 8–20 Hz
23 Venous ulcer 15 50 50 10–14 Hz
24 Brain dysfunction 25 70 70 25 + 2–25 Hz
25 Polyneuropathy 25 80 90 10 and 2–25Hz 10–50 Hz
26 Periodontal disease 45 80 100 4–6 and 16–20Hz
27 Muscle 30 80 100 23–25 Hz 65–79 Hz
28 Regeneration 25 80 90 20–25 Hz 65–79 Hz
29 Before massage 20 80 100 6–10 and 10–14 Hz
30 Relaxation 45 70 70 2 + 4–11 Hz
31 Magnetisation 20 80 100 16 + 8–20 Hz
32 Program Individual 5 to 120 10 to 100 1 to 100 your settings
1 to 81 Hz your settings 1 to 162 Hz