Bionaire BAP830RCS User manual

while attaching the filter clip to the filter. Align
the clip on the side of your HEPA filter with the
rails on the inside of the unit.
NOTE: The pleated material and rubber gasket
should be facing towards the unit when applied.
5. Align the clips on the side of your HEPA filter with
the rails on the inside of the unit. Gently slide
the filter onto the rails (see fig. 3).
6. Replace the inlet grill by sliding back on to the
unit. Make sure that it snaps securely into position
(the grill only goes on one way)
NOTE: Do not point outlet towards wall.
7. The filter life indicator light (E) should be reset
once the HEPA filters have been replaced.
Reset the indicator by pressing the Power
button ( ) on the control panel for 2 seconds.
REPLACEMENT FILTERS
BAPF30 HEPA Filter (usage 2 pcs)
Holmes Products (Europe) Ltd reserves the right
to change or modify any specifications without
notice.
For U.K. and Ireland only:
If the plug is not suitable for the socket outlets in
your home, it can be removed and replaced by
a plug of the correct type.
Please refer to "Installation of a plug" below.
Installation of a plug Applicable to
U.K. and Ireland.
WARNING - THIS APPLIANCE MUST BE
EARTHED
The wires in the mains lead are coloured as such:
GREEN AND YELLOW - EARTH
BROWN - LIVE
BLUE - NEUTRAL
Please note that the colour of these mains wires
may not correspond with the colour markings
that identify the terminals in your plug.
Please proceed as follows:
The wire which is coloured GREEN AND YELLOW
must be connected to the terminal which is marked
with the letter 'E' or by the earth symbol or
coloured GREEN or GREEN AND YELLOW.
The BROWN coloured wire must be connected
to the terminal, which is marked with the letter
"L" or is coloured RED.
The BLUE coloured wire must be connected to
the terminal, which is marked with the letter "N"
or is coloured BLACK.
NOTE: If the terminals in the plug are not marked
or if you are unsure or in doubt about the installation
of the plug please contact a qualified electrician.
If a 13A 3-pin plug is fitted, it must be an ASTA
approved plug, conforming to BS1363 standard.
Replacement 3A fuses must be BSI or ASTA
BS1362 approved.
GUARANTEE
PLEASE KEEP YOUR RECEIPT AS THIS WILL
BE REQUIRED FOR ANY CLAIMS UNDER THIS
GUARANTEE.
• This appliance is guaranteed for 2 years.
•In the unlikely event of breakdown from a
manufacturing related fault, please return it to
the place of purchase, with your till receipt and
a copy of this guarantee.
•The rights and benefits under this guarantee
are additional to your statutory rights which are
not affected by this guarantee.
• Holmes Products (Europe) Ltd undertakes
within the specifiied period, to repair or
replace free of charge, any part of the
appliance found to be defective from a
manufacturing fault provided that:
•We are promptly informed of the defect.
•The appliance has not been altered in any
way or subjected to misuse or repair by a
TROUBLESHOOTING
Problem Solution
Unit will not operate Check to make sure the unit
is plugged in.
Check to make sure the unit
is on by
pressing the Power
button .
Make sure the filters are
properly installed and firmly
close the door.
Decreased air flow If the filters have not been
changed for 6 month or more,
change the HEPA filters.
Check to ensure nothing is
blocking the air inlet and
filtered air outlet.
Noisy Ensure all plastic bags
have been removed from
the filters.
4
Holmes Products (Europe) Ltd
1 Francis Grove
London SW19 4DT
England
Fax: [phone]
Email: [email protected]
Website address: www.bionaire.com
UK - Filter Sales Order Line - 0870 759 9000
UK - Free phone Customer Service Helpline – 0800 052 3615
9100040002921
BAP830RCSIUK07EM1
Tower Air Purifier
BAP830RCS
person other than a person authorised by
Holmes Products (Europe) Ltd.
• Faults that occur through normal wear and tear
are not covered by this guarantee.
• No rights are given under this guarantee to a
person acquiring the appliance second hand
or for commercial or communal uses.
• Any repaired or replaced appliance will be
guaranteed on these terms for the remaining
portion of the guarantee.
THIS PRODUCT IS MANUFACTURED TO
COMPLY WITH THE E.E.C. DIRECTIVES
73/23/EEC, 2004/108/EC and 98/37/EEC.
Waste electrical products should not be
disposed of with Household waste.
Please recycle where
facilities exist.
Check on the following website
for further recycling and WEEE
information:
www.bionaire.com or e-mail
[email protected]
5
© 2007 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
BAP830RCS-IUK_07EM1.qxd 4/25/07 20:51 Page 1

Figure 4
F
E
G
H
I
Figure 5
J
I
H
G
L
K
You may also note, after extended use, that dust
may have collected around the grills or front panel.
This is from the ionisation effect caused by the
negative ions exiting from the air outlet.This dust
does not come from the air output, but is drawn
out of the uncleaned air going past the air outlet.
This is additional evidence of the air cleaning
effectiveness of negative ions. The dust can be
easily removed with a clean, dampened cloth or
soft brush.
NOTE: it is important to change the HEPA filter
at recommended intervals. Using the ioniser in
conjunction with dirty filters may result in dirty
particles exiting the air purifier and being attracted
to walls, carpets, furniture and other household
objects. These dirty particles may prove very difficult
to remove.
PRE-OPERATING INSTRUCTIONS
1. After removing the unit from the box, remove
the plastic covering from the unit.
2. Select a firm level place where there are no
obstructions to the air inlet (rear grill) (A) or
filtered air outlet (D).
3. Remove the inlet grill by pulling the grill (A)
towards you.
4. Remove both HEPA filters (C) by gripping on
both sides and pulling forward.
5. Remove protective plastic bag from each filter
cartridge. Install the filter clip to the HEPA
filters. The filter clip can only be attached to
the hang tabs on the filter one way (see fig 2).
The filter clip should easily slide onto the filter
hang tabs. Do not use force whilst attaching
the filter clip to the filter. Align the clip on the
HEPA filter with the rails on the inside of the unit
(see fig. 3).
NOTE: The pleated material and rubber gasket
should be facing towards the unit when applied.
6. Replace the inlet grill by sliding back on to the
unit. Make sure that it snaps securely into position
(the grill only goes on one way).
NOTE: Do not point outlet towards wall.
OPERATING INSTRUCTIONS FOR THE
CONTROL PANEL AND REMOTE
CONTROL
1. Plug into a 220-240V electrical outlet.
2. Press the Power button ( ). The unit will turn
onto high and the power light (J) will illuminate
letting you know the power is on.
3. You can then select the desired speed setting.
This air purifier has three speed settings. You
can select from HIGH ( ), MEDIUM ( ), or
LOW ( ) by pushing the desired operating
speed button on the control panel or the remote
control.
4. To release negative ions into the filtered air,
press the ioniser button ( ) to ON and the
light will illuminate.
5. For optimum air filtration, it is recommended
to operate the air purifier continuously. Its
rugged motor has been designed to give
many years of use.
For continuous use, it’s recommended to operate
the air purifier at the MEDIUM setting. For quieter
operation or use in a bedroom, select the LOW
setting. When high levels of air pollution are present,
select the HIGH setting to quickly circulate and
filter the room air.
REMOTE CONTROL
Your remote control requires (2) AAA batteries for
operation. To install the batteries, simply depress
and slide the back of the remote control with your
thumb on the arrow indentation. Insert batteries
according to the diagram shown inside and replace
cover.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon-zinc)
or rechargeable (nickel-cadmium) batteries.
CLEANING AND MAINTENANCE
1. Turn the air purifier off and unplug it before cleaning.
2. The outside of the air purifier can be cleaned
with a soft, clean dampened cloth.
3. The filtered air outlet on the top of the unit can
be cleaned of dust with a small, soft brush.
4. If you wish to clean the inside of the air purifier,
please only use a dry, soft cloth to wipe it down.
FILTER REPLACEMENT
IMPORTANT: IN ORDER TO RETAIN THE
EFFICIENCY OF YOUR AIR PURIFIER, THE
HEPA FILTER NEEDS TO BE CHANGED EVERY
3-6 MONTHS.
1. Every few weeks check the condition of the
pre-filter (B).
2. Remove the inlet grill (A). If the foam pre-filter
has collected a noticeable amount of dust,
remove it from the inlet of the grill and wash it
in warm soapy water. Rinse and dry the pre-filter
thoroughly before replacing it in the inlet of the
grill.
3. With the inlet grill (A) removed, remove the
HEPA cartridge (C) and dispose in the
dustbin. DO NOT try to wash and re-use the
HEPA filter. Replace with a new HEPA filter-
BAPF30 removing the protective plastic bag
before inserting into the air purifier.
4. Install the filter clip to the HEPA filters. The
filter clip can only be attached in one direction
(see fig. 2). The filter clip should easily slide
onto the filter hang tabs. Do not use force
3
Figure 1 BAP830RCS
D
B
C
A
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS.
With proper care and use, this Bionaire®air purifier
will give you fresh, clean air for many years.
NOTE: Before reading these instructions, please
view the corresponding illustrations.
DESCRIPTIONS (SEE FIG 1/4/5)
A. Inlet Grill
B. Washable Foam Pre-Filter
C.HEPA Filter
D.Filtered Air Outlet
E. Filter Indicator Light
F. Ioniser Light
G.Ioniser Control
H.Power Button
I. Speed Control
J. Power Indicator Light
K. Infrared
L. Operation Indicator Light
SAFETY PRECAUTION
Carefully read and retain all instructions before
using the air purifier.
•To avoid fire or shock hazard, check that the
voltage on the product corresponds to your
electricity supply and plug directly into an
electrical outlet.
•To avoid fire hazard, never put the cord under
rugs, or near any heat source.
•Carefully discard any plastic wrapping that
was used for the packaging.
•Do not use the air purifier outside.
•Do not place the unit near any heat source or
in direct sunlight.
•Always unplug the air purifier before removing
the grill, changing the filters, cleaning the air
purifier or whenever it is not in use.
•Do not use in or around water or any other
liquids.
•Do not attempt to wash the unit under running
water.
•Use appliance only for intended household
use as described in this manual.
•Ensure that all air openings are not restricted
or covered in any way.
•Do not place anything on top of the unit.
•Never insert any object into any openings.
•Do not use the air purifier if any part is
missing or damaged in any way.
•Do not attempt to repair or adjust any
mechanical functions of this unit. If the unit
becomes damaged return to the place of
purchase or phone the helpline number on the
back of this leaflet.
•If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid hazard.
•The air purifier contains no user serviceable
parts and should the product suffer damage or
breakdown, it must be returned to the
manufacturer or its service agent.
•Should the air purifier stop working, first check
the fuse in the plug (UK only) or fuse/circuit breaker
at the distribution board is operating, before
contacting the manufacturer or service agent.
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety. Children
should be supervised to ensure that they do
not play with the appliance.
HOW THE AIR PURIFIER WORKS
Dirty, dust laden air is drawn through the rear of
the air purifier and through the multi-stage filtration
system.
1. The baking soda filter will help clear odours
making the air cleaner and fresher.
2. The HEPA filter entraps 99% of all smaller visible
and non-visible particles down to 2 microns in
size.
PRODUCT FEATURES
Filter Life Indicator
Your air purifier has an indicator light (E) that
illuminates when its time to change the filters.
Ioniser
Your Bionaire®Air Purifier has an independently
controlled ioniser, which when turned on, releases
negative ions into the outgoing filtered air. Ions
are tiny particles that carry either a positive or
negative charge. These ions exist naturally all
around us in the air, water and ground. Both positive
and negative ions are colourless, odourless and
completely harmless.
Negative ions help the air purification process by
attaching themselves to very small airborne particles
in the room. These particles take on a negative
charge and may join with positively charged particles,
such as dust, pollen, smoke and pet dander to form
larger particles that are then more readily captured
by the filter system, or they may be attracted to
positively charged surfaces like walls or floors.
U.K. and IRELAND
2
Figure 2 Figure 3
BAP830RCS-IUK_07EM1.qxd 4/25/07 20:51 Page 5