Birlea PHOENIX OTTOMAN 4' User manual

Vendor: S000307
Page 1 of 9
ASSEMBLY INSTRUCTIONS
PHOENIX OTTOMAN 4’
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR PHOENIX
OTTOMAN 4’ BED FRAME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame if any parts are missing, damaged or worn.
DO NOT use this bed frame unless all fixings are secured.
Please keep small parts out of reach of children.
lways use on a level, even surface.
WARNING: If th s bed s placed on a non-carpeted floor you must place some protect on under all legs to stop
the bed frame from mov ng. If th s s not adhered to there s no guarantee f the bed frame collapses.
CARE & MAINTENANCE:
ssemble in the room of use.
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the bed frame as this will damage the legs.
lways lift the bed with two people to reposition.
Keep any sharp objects away from the frame.
www.birlea.com

Vendor: S000307
Page 2 of 9
Parts L st
Part Descr pt on Box Qty
1 Headboard Frame
1 1
2 Left Wooden Post
2 1
3 Right Wooden Post
2 1
4 Footboard
1 1
5 Left Side Rail
4 1
6 Right Side Rail
4 1
7 Centre Storage Panel
2 2
8 Back Storage Panel
2 1
9 Small Base Panel
1 1
10 Large Base Panel
1 3
11 Slat
3 28
12 Left Hydraulic Base Support
with Stopper
5 1
13 Right Hydraulic Base Support
5 1
14 Hydraulic Pump
5 2
15 Back Bed Base
3 1
16 Front Bed Base
3 1

Vendor: S000307
Page 3 of 9
Hardware L st (Found n box 3)
Part Descr pt on Qty
A Mini Fix
12
B 8 x 30 mm Wooden Dowel
16
C Metal Corner Block
2
D M6 x 90 mm Barrel Nut
4
E M8 x 25 mm JCBC Bolt
16
F M8 x 15 mm JCBC Bolt
8
G M8 x 20 mm JCBC Bolt
10
H M8 x 75 mm JCBC Bolt
4
I M8 Flat Washer
4
J Base Nut
4
K Base Handle
2
L M6 x 40 mm JCBC Bolt
4
M M8 x 45 mm Bolt with Hex Nut, Spring & Flat Washer
6
N Single Slat Cap
28
O Double Slat Cap
14
P Wooden Button
4
Q M6 llen Key
1
R M8 llen Key
1
S M12.8 Spanner
1
T M14 Spanner
1
**You w ll also need a screwdr ver and small mallet (not prov ded).

Vendor: S000307
Page 4 of 9
Step 1: ttach the headboard frame (1) and back storage panel (8) to the left wooden post (2) and right
wooden post (3). Secure the headboard frame using hardware parts B, D and P, then secure the back
storage panel with hardware parts and B.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 2: Join together the left side rail (5) and right side rail (6) with the centre storage panels (7) using
hardware parts and B.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000307
Page 5 of 9
Step 3: ttach the headboard frame (1) and footboard (4) using hardware part E.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 4: ttach hardware part C using hardware parts F.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000307
Page 6 of 9
Step 5: ttach the hydraulic pumps (14) to the left hydraulic base support (12) and right hydraulic base
support (13) then fix the base supports to the side rails using hardware part G as shown in Fig 5.2 – do not
fully tighten yet. Insert the remainder of hardware part G and fully tighten all bolts.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 6: Join together the back bed base (15) and front bed base (16) using hardware parts H, I and J. ttach
hardware parts K using hardware part L.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000307
Page 7 of 9
Step 7: Insert the slats (11) to hardware parts N and O then press into the base making sure they are secure.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 8: Insert the small base panel (9) and large base panels (10).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 9: ttach the bed base to the hydraulic frames using hardware part M. Fix the bolts starting from area 1
and finishing in area 3 – do not fully tighten the bolts yet.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000307
Page 8 of 9
Step 10: djust the bed base making sure that the distance to the footboard is approximately 10 – 15 mm.
Tighten all bolts and screws now.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Additional Information:
• For complete product information, images and dimension diagrams please visit the
website www.birlea.com
• If you have any issues with your item please contact the retailer directly you
purchased it from who will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be
shared in our #birleahome feature on Instagram.

Vendor: S000307
Page 9 of 9
Caution: Please use the hydraulic pump stopper for
safety purposes.