Birlea CORONA 2+2 DRAWER CHEST User manual

Vendor: S000242
Page 1 of 9
ASSEMBLY INSTRUCTIONS
CORONA 2+2 DRAWER CHEST
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 2+2
DRAWER CHEST.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly.
To avoid damages assemble the item on a soft, clean surface.
Assemble in the room of use.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fi ings are secured.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Keep small parts out of the reach of children.
CARE & MAINTENANCE:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to the production process, however, this will disappear
after a period of time.
DO NOT place the item ne t to a radiator or direct sunlight as this item is susceptible to temperature
change. It is recommended to maintain an even room temperature with no sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.
You may wish to re-treat the surface to maintain the original finish. This can be done using block wa (un-
perfumed). Please follow the manufacturer’s instructions carefully.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Periodically check all screws & fi ings to ensure they are secure.
DO NOT push the item as this will damage the base.
Keep any sharp objects away from the item.
www.birlea.com

Vendor: S000242
Page 2 of 9
Parts L st Hardware L st
Part Descr pt on Qty Part Descr pt on Qty
1
Top Panel
1
A 3.3 35 mm Screw 46
2
Left Panel
1
B 8 25 mm Wooden Dowel
44
3
Right Pa
nel
1
C
Handle
6
4
Front Frame
1
D 3/16 5/8 Screw 6
5
Back Crossbeam
1
E 10 10 mm Tack 26
6
Side Plinth
2
F Stud 4
7
Front Plinth
1
G 3.5 35 mm Screw 36
8
Drawer Runner
6
** You w ll need a small mallet and a screwdr ver.
9
Back Panel
1
10
Large Drawer Front
1
11
Large Drawer Side
2
12
Larg
e Drawer Base
2
13
Large Drawer Back
1
14
Medium Drawer Front
1
15
Drawer Side
6
16
Medium Drawer Back
1
17
Centre Drawer Runner
1
18
Support Block
1
19
Small Drawer Front
2
20
Small Drawer Base
2
21
Small Drawer Back
2

Vendor: S000242
Page 3 of 9
Step 1: Insert hardware part B using a small mallet (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 2: Attach four drawer runners (8) to the left panel (2) and right panel (3) using hardware part A and a
screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 4 of 9
Step 3: Attach the back crossbeam (5) to the left panel (2) and right panel (3) using hardware part A and a
screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 4: Attach the front frame (4) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 5 of 9
Step 5: Attach the top panel (1) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 6: Attach the support block (18) to the centre drawer runner (17) using hardware part A and a
screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 7: Attach the remaining drawer runners (8) and the centre drawer runner (17) using hardware part A
and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 6 of 9
Step 8: Attach the side plinths (6) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 9: Attach the front plinth (7) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 7 of 9
Step 10: Attach the back panel (9) using hardware part E and a small mallet (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 11: Assemble the small drawer components using hardware parts C, D and G with a screwdriver (not
provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 8 of 9
Step 12: Assemble the medium drawer components using hardware parts C, D and G with a screwdriver (not
provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 13: Assemble the large drawer components using hardware parts C, D and G with a screwdriver (not
provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000242
Page 9 of 9
Step 14: Secure the drawers using hardware part B, then insert hardware part F. You will need to use a small
mallet (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Additional Information:
• For complete product information, images and dimension diagrams please visit the website
www.birlea.com
• If you have any issues with your item please contact the retailer directly you purchased it from who
will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be shared in our
#birleahome feature on Instagram.