Birlea Corona 1 User manual

Vendor: S000242
Page 1 of 8
ASSEMBLY INSTRUCTIONS
CORONA 1 DRAWER BOOKCASE
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 1
DRAWER BOOKCASE.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly.
To avoid damages assemble the item on a soft, clean surface.
Assemble in the room of use.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fi ings are secured.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Keep small parts out of the reach of children.
CARE & MAINTENANCE:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to the production process, however, this will disappear
after a period of time.
DO NOT place the item ne t to a radiator or direct sunlight as this item is susceptible to temperature
change. It is recommended to maintain an even room temperature with no sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.
You may wish to re-treat the surface to maintain the original finish. This can be done using block wa (un-
perfumed). Please follow the manufacturer’s instructions carefully.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Periodically check all screws & fi ings to ensure they are secure.
DO NOT push the item as this will damage the base.
Keep any sharp objects away from the item.
www.birlea.com

Vendor: S000242
Page 2 of 8
Parts List Har ware List
Part Description Qty Part Description Qty
1
Top Panel
1
A 3.5 35 mm Screw 16
2
Left Side Panel
1
B 8 25 mm Wooden Dowel 24
3
Right Side Panel
1
C 10 10 mm Tack 22
4
Lower Back Crossbeam
1
D
Shelf Support
8
5
Front Frame
1
E 3.5 30 mm Screw 13
6
Drawer
Runner
2
F 3.5 14 mm Screw
2
7
Side Plinth
2
G
Bracket
1
8
Back Panel
1
H
Stud
4
9
Base Panel
1
J
Handle
2
10
Shelf
2
K
3/16 5/8 Screw
2
11
Front Plinth
1
L 3.5 35 mm Bolt 8
12
Drawer Front
1
N
Support
6
13
Drawer Side
2
** You will nee a small mallet an a screw river.
14
Drawer Base
1
15
Drawer Back
1

Vendor: S000242
Page 3 of 8
Step 1: Insert hardware parts A, B and D with a small mallet and screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 4 of 8
Step 2: Attach the left side panel (2) and right side panel (3) to the base panel (9) and lower back crossbeam
(4) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 3: Attach the top panel (1) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 5 of 8
Step 4: Attach the front frame (5) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 5: Attach the side plinths (7) with hardware part E. Secure hardware part G using hardware part F. You
will need to use a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 6 of 8
Step 6: Attach the front plinth (11) using hardware part E and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 7: Assemble the drawer components with hardware parts J, K and L with a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 7 of 8
Step 8: Insert hardware part H then insert the assembled drawer and secure using hardware part B. You will
need to use a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 9: Insert the shelves (10) and fi the lower back crossbeam (4) into position using hardware part A and
a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 8 of 8
Step 10: Attach the back panel (8) using hardware part C and a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Additional Information:
• For complete product information, images and dimension diagrams please visit the website
www.birlea.com
• If you have any issues with your item please contact the retailer directly you purchased it from who
will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be shared in our
#birleahome feature on Instagram.