Birlea Toronto Bed User manual

1/5
D 00056
ASSEMBLY INSTRUCTION
WOODEN GUEST BED
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR
USING BED FRAME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame if any parts are missing, damaged or worn.
DO NOT use this bed frame unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
WARNING: If this bed is placed on a non-carpeted floor you must place some protection under all
legs to stop the bed frame from moving. If this is not adhered to there is no guarantee if the bed
frame collapses.
CARE & MAINTENANCE:
Assemble in the room of use.
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the bed frame as this will damage the legs.
Always lift the bed with two people to reposition.
Keep any sharp objects away from the frame.

2/5
PART LIST
HARDWARE LIST
PART
DESCRIPTION
QTY
PART
DESCRIPTION
QTY
TOP FRAME
1
HEADEND
1
A
M8 x 20mm Bolt
8
2
FOOTEND
1
B
M4 x 32mm CSK Screw
8
3
SIDE RAIL
2
C
M8 FLAT WASHER
8
4
SLAT
13
TRUNDLE
5
TRUNDLE ENDBOARD
2
E
CASTER WHEEL
4
6
TRUNDLE SIDE RAIL
2
F
M6 x 50 mm Bolt
4
7
TRUNDLE LEG BAR
2
G
M4 x 32mm CSK Screw
8
8
TRUNDLE SLAT
13
H
M6 x 60mm Bolt
4
I
M8 X 40 Wooden Dowel
8
J
Wooden Button 13.5mm
4
K
M6 Barrel Nut
4
L
M4 ALLEN KEY
1
M
M5 ALLEN KEY
1
N
M10 X 50 Wooden Dowel
4
** You will need a screwdriver ( not provided )

3/5
Step 1 : Attach the side rail (3) to the headend (1) using 2 pieces of hardware A & C each
side but do not fully tighten (left 10mm space ) using hardware M . Place the side rail
brackets over the bolts as shown –when the bolt ends of the side rail(3) are attached , tighten
securely using hardware part M , repeating for both sides
DO NOT use any power tools as this may damage the frame and will invalidate any claim
Step 2 : Attach the slat (4) to the side rail (3) using hardware part (B) and fully tighten using
a screwdriver(not provided) .
Remark : Screw the first & last slat after the slat fix screw 5th and 9th as the guide hole.
DO NOT use any power tools as this may damage the frame and will invalidate any claim

4/5
Step 3 : Push hardware part E firmly into the holes on the trundle side rail (6)
CAUTION : When the leg ties are cut , the legs spring back
DO NOT use any power tools as this may damage the frame and will invalidate any claim
Step 4 : Attach the leg bars (7) using hardware parts N & H , tighten using hardware L.
DO NOT use any power tools as this may damage the frame and will invalidate any claim

5/5
Step 5 : Insert hardware part I into the holes in the side rail (6) until fully inserted then attach the end
boards (5) to the trundle side rail(6) using hardware K, F & J , tighten using hardware L.
DO NOT use any power tools as this may damage the frame and will invalidate any claim
Step 6 : Attach the slat (8) to the trundle side rail (6) using hardware part G and fully tighten
using a screwdriver (not provided)
Remark : Screw the first & last slat after the slat fix screw 5th and 9th as the guide hole.
DO NOT use any power tools as this may damage the frame and will invalidate any claim