Birlea corona User manual

Vendor: S000242
Page 1 of 9
ASSEMBLY INSTRUCTIONS
CORONA 4 DRAWER DRESSING TABLE
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 4
DRAWER DRESSING TABLE.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly.
To avoid damages assemble the item on a soft, clean surface.
Assemble in the room of use.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fi ings are secured.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Keep small parts out of the reach of children.
CARE & MAINTENANCE:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to the production process, however, this will disappear
after a period of time.
DO NOT place the item ne t to a radiator or direct sunlight as this item is susceptible to temperature
change. It is recommended to maintain an even room temperature with no sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.
You may wish to re-treat the surface to maintain the original finish. This can be done using block wa (un-
perfumed). Please follow the manufacturer’s instructions carefully.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Periodically check all screws & fi ings to ensure they are secure.
DO NOT push the item as this will damage the base.
Keep any sharp objects away from the item.
www.birlea.com

Vendor: S000242
Page 2 of 9

Vendor: S000242
Page 3 of 9
Parts List Har ware List
Part Description Qty Part Description Qty
1
Top Panel
1
A 3.5 35 mm Screw 29
2
Left Panel
1
B 8 25 mm Wooden Dowel 28
3
C
entre Panel
1
C 4.5 16 mm Screw 24
4
Front Crossbeam
1
D 3/16 5/8 Screw 4
5
Back Crossbeam
1
E 10 10 mm Tack 14
6
Side Plinth
2
F
Handle
4
7
Front Plinth
1
G
Stud
2
8
Drawer Runner
8
H 3.5 35 mm Screw 36
9
Back Panel
1
** You will nee a small mallet an a screw river.
10
Right Panel
1
11
Plinth
1
12
Long Back Crossbeam
1
13
Long Front Crossbeam
1
14
Small Drawer Front
1
15
Small Drawer Side
2
16
Drawer Base
4
17
Small Drawer Back
1
18
Drawer Front
2
19
Drawer Side
4
20
Drawer Back
2
21
Large Drawer Front
1
22
Lar
ge Drawer Side
2
23
Large Drawer Back
1
Step 1: Insert hardware parts B and C using a small mallet and screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 4 of 9
Step 2: Attach the left panel (2) and centre panel (3) to the front crossbeam (4) and back crossbeam (5)
using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 3: Attach the side plinths (6) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 5 of 9
Step 4: Attach the front plinth (7) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 5: Attach the long back crossbeam (12) and long front crossbeam (13) to the right panel (10) using
hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 6: Attach the plinth (11) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 6 of 9
Step 7: Join together the two sections using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 8: Attach the top panel (1) using hardware part A and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 7 of 9
Step 9: Secure the back panel (9) using hardware part E and a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 10: Assemble the drawer components using hardware parts A, F and H with a screwdriver (not
provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 8 of 9
Step 11: Assemble the drawer components using hardware parts A, F and H with a screwdriver (not
provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 12: Assemble the drawer components using hardware parts A, F and H with a screwdriver (not
provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000242
Page 9 of 9
Step 13: Insert the assembled drawers then insert hardware part G using a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Additional Information:
• For complete product information, images and dimension diagrams please visit the website
www.birlea.com
• If you have any issues with your item please contact the retailer directly you purchased it from who
will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be shared in our
#birleahome feature on Instagram.