Birlea corona User manual

Vendor: S000238
Page 1 of 7
ASSEMBLY INSTRUCTIONS
CORONA 4’ HIGH END BED
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 4’ HIGH
END BED FRAME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame if any parts are missing, damaged or worn.
DO NOT use this bed frame unless all fixings are secured.
Please keep small parts out of reach of children.
lways use on a level, even surface
WARNING: If thi bed i placed on a non-carpeted floor you mu t place ome protection under all leg to top
the bed frame from moving. If thi i not adhered to there i no guarantee if the bed frame collap e .
CARE & MAINTENANCE:
ssemble in the room of use.
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the bed frame as this will damage the legs.
lways lift the bed with two people to reposition.
Keep any sharp objects away from the frame.
This product is manufactured in pine which has natural characteristics including knots, grains, clusters or
indentations.
On unpacking you may notice an odour due to production processes. Tthis will disappear after a period of
time.
DO NOT place the item next to a radiator or direct sunlight – this item is manufactured in pine but is
susceptible to temperature change. It is recommended an even room temperature be maintained with no
sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as use of these materials would invalidate any claims.
To retreat the surface use block wax (un-perfumed). Please follow the manufacturer’s instructions carefully
DO NOT place the item onto wet or damp flooring as staining may occur to the floor
www.birlea.com

Vendor: S000238
Page 2 of 7
Part Li t Hardware Li t (found in box 2)
Part De cription Box Qty Part De cription Qty
1 Headend Panel 1 1 A 30 mm Wooden Dowel b
2 Footend Panel 1 1 B 40 mm Wooden Dowel 4
3 Left Headend Post 2 1 C 16 mm Screw 8
4 Right Headend Post 2 1 D 35 mm Screw 52
5 Right Footend Post 2 1 E 32 mm Bolt 2
6 Left Footend Post 2 1 F Nut 2
7 Slat 3 26 G 50 mm Bolt 2
8 Support Leg 3 2 H 130 mm Bolt 10
9 Side Rail 3 2 J 130 mm Bolt 8
10 Centre Rail 3 1 K Elliptical Nut 8
11 Headend Rail 3 1 L Metal Bracket 2
** You will need a mall mallet and a
crewdriver
M llen Key 1
N Spacer 2
P Stud 8

Vendor: S000238
Page 3 of 7
Step 1: ttach the support legs (8) to the centre rail (10) using hardware parts G and M. Insert hardware part
B using a small mallet (not provided).
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Step 2: Insert hardware part using a small mallet (not provided).
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Step 3: ttach the left headend post (3) and right headend post (4) to the headend panel (1) and headend
rail (11) using hardware parts H and M.
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.

Vendor: S000238
Page 4 of 7
Step 4: ttach the left footend post (6) and right footend post (5) to the footend panel (2) using hardware
parts H and M.
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Step 5: Secure hardware part L using hardware part C and a screwdriver (not provided).
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Step 6: ttach the side rails (9) using hardware parts J, K and M. Secure the centre rail (10) using hardware
parts E and F.
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.

Vendor: S000238
Page 5 of 7
Step 7: Join the two sections together using hardware parts J, K and M. Secure the centre rail (10) using
hardware parts E and F.
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Step 8: Secure the slats (7) using hardware parts D and N with a screwdriver (not provided). Make sure to
start at the ends and work towards the middle.
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.

Vendor: S000238
Page 6 of 7
Step 9: Insert hardware part P using a small mallet (not provided).
DO NOT u e any power tool a thi may damage the frame and will invalidate any claim.
Note: When everything ha been a embled, tighten all bolt and attach the wooden button to the hole on
the bed po t .
Additional Information:
• For complete product information, images and dimension diagrams please visit the
website www.birlea.com
• If you have any issues with your item please contact the retailer directly you
purchased it from who will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be
shared in our #birleahome feature on Instagram.

Vendor: S000238
Page 7 of 7