Bison TN10P User manual

1
—— Instruction Manual ——
Competition Portable Tennis System
TN10P
P A R T S L I S T
Item Qty Description Item Qty Description
A1Winch Post L21/2” Lock Nut
B1Non-Winch Post M4Connecting Bar
C1Removable Winch Handle N16 3/8” X 1” Hex Bolt
D1TN10NP Tennis Net O25/16” X 1” Carriage Bolt
E3Spreader Tube P25/16” Flat Washer
F4Inner Tube Q25/16” Lock Washer
G2Stabilizer Leg R25/16” Hex Nut
H2Clamp S1TN10P Center Strap Anchor
I85/16” X 3/4” Button Head Bolt T1TN10CS Center Court Hold Down Strap
J4Wheel U2Lacing Cord
K21/2” X 7 1/2” Hex Bolt
Date: 3/13/20 Rev: 1 B.A. N.J.C. File: \pub\TN10P Ref#: 960941
 Inspect all contents prior to installation. Report any missing parts to dealer immediately.
 Read all instructions before proceeding.
1. Slide the Connecting Bar (M) into the Inner Tube (F) through the channel so that all the holes are lined up
as shown. Insert the inner tube assembly into either the Winch Post (A) or the Non Winch Post (B) leaving
six holes exposed for the Spreader Tube (E) attachment. Using two of the 3/8” X 1” Hex Bolts (N) loosely
attach the inner tube assembly to the Winch Post (A). Slide a Spreader Tube (E) over the exposed portion
of the inner tube assembly and attach it using two more 3/8” X 1” Hex Bolts (N). Continue the same
process with two more Spreader Tubes (E) followed by the Non Winch Post (B). Tighten all of the 3/8” X
1” Hex Bolts (N). See Figures 1 & 7.
2. Loosen the set screws that secure the lacing bars to the Winch Post (A) and the Non Winch Post (B). Slide
the lacing bar up, then using the 5/16” X 3/4” Button Head Bolts (I) attach the Clamp (H) to the Stabilizer
Leg (G) Assembly. Leave the 5/16” X 3/4” Button Head Bolts (I) hand tight. Slide the lacing bar back in
its original position and tighten the set screw. See Figure 2.
3. Remove one of the 3/8” X 1” Hex Bolts (N) on the middle Spreader Tube (E). Slide the 5/16” X 1”
Carriage Bolts (O) down the groove in the Spreader Tube (E) towards the middle. Replace 3/8” X 1” Hex
Bolt (N). Measure approximately 77 7/8” from the end of the middle Spreader Tube (E) and make a small
mark. Place the TN10P Center Strap Anchor (S) over the 5/16” X 1” Carriage Bolts (O). Line the edge of
the TN10P Center Strap Anchor (S) up with the mark made earlier. Tighten it down to the Spreader Tube
(E) using the 5/16” Flat Washers (P), 5/16” Lock Washers (Q), and the 5/16” Hex Nuts (R).
See Figures 3 & 4.

2
Figure 1
Figure 2
4. Stretch out TN10NP Tennis Net (D) across the court.
5. Hook the loop on the TN10NP Tennis Net (D) top cable around the net retaining pin on Non-Winch Post
(B) and over the top pulley. See Figure 5.
6. Cut off loop and remove 12” of nylon cable coating from the top net cable, run cable over the top groove of the
net cable pully down the outside of the post. Insert cable into the winch cable hole on the Winch Post (A). Use the
Removable Winch Handle (C) to crank cable until you achieve 38” at the center of TN10NP Tennis Net (D).
See Figure 6.

3
7. Insert dowels through the end side tapes of TN10NP Tennis Net (D).
8. Square up TN10NP Tennis Net (D) to each post, use Lacing Cord (U) to secure TN10NP Tennis Net (D) to each
post. See Figure 5.
9. Attach TN10CS Center Court Hold Down Strap (T) to the strap retaining bar on the TN10P Center Strap Anchor (S).
Adjust TN10CS Center Court Hold Down Strap (T) so top of TN10NP Tennis Net (D) measures 36” at the center.
See Figure 4.
10. After the net is at the desired height and tension make sure the Stabilizer Legs (G) are fully contacting the
playing surface then tighten all of the 5/16” X 3/4” Button Head Bolts (I). See Figure 2.
11. Using the 1/2” X 7 1/2” Hex Bolt (K) and the 1/2” Lock Nut (L) bolt two Wheels (J) onto each Stabilizer Leg (G).
Make sure Wheels (J) are installed on the same side of the posts. See Figures 2 & 7.
Figure 3 Figure 4
Figure 5
Figure 6

4
BASELINE
CENTER MARK
DOUBLES SIDELINE
SINGLES SIDELINE
SERVICE LINE
CENTER
SERVICE LINE
NET POST
NET
4'6" (1.37m)
3'0" (.941m)
21'0" (6.40m)
78'0" (23.77m)
36'0" (10.97m)
27'0" (8.23m)
Figure 7