Bissell FMU-2000 Guide

Make a copy of this card for future reference.
2013 © BISSELL BigGreen Commercial. All rights reserved.
New Equipment Warranty
Limited Warranty
The manufacturer gives you the following limited warranty for this product if it was originally
purchased for use, not resale, from BISSELL BigGreen Commercial or a BISSELL BigGreen
Commercial-Authorized Retail Dealer.
The manufacturer will repair or replace, free of charge, to the original purchaser, any part
which is found to be defective in material or workmanship within one (1) year of the date of
purchase; ve (5) years on the motor and gear box.
Drive belts, brushes, and other parts subject to normal wear are not covered by this limited
warranty. This limited warranty does not apply to any part subjected to accident, abuse,
or alteration, misuse, damage caused by re or act of God, the use of voltages other than
indicated on the serial number plate of this product or service of this product by other than a
trained service technician.
The manufacturer does not authorize any person or representative to assume or grant any
other warranty obligation with the sale of this product.
The manufacturer’s limited warranty is valid only if you retain proof of purchase from BISSELL
BigGreen Commercial or a BISSELL BigGreen Commercial-Authorized Retail Dealer for this
product. If you purchase this product from any other source, your purchase is“AS IS,”which
means the manufacturer grants you no warranty, and that you, not the manufacturer, assume
the entire risk of the quality and performance of this product, including the entire cost of any
necessary servicing or repairs of any defects.
The manufacturer’s liability for damages to you for any costs whatsoever arising out of this
statement of limited warranty shall be limited to the amount paid for this product at the
time of original purchase, and the manufacturer shall not be liable for any direct, indirect,
consequential or incidental damages arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so the above
limitation may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary
from state to state.
BISSELL BigGreen Commercial
100 Armstrong Road | Suite 101 | Plymouth, MA 02360
Phone: [phone] | Fax: [phone]
www.bissellcommercial.com
2013 © BISSELL BigGreen Commercial. All rights reserved.
Important Information and Safety Instructions
Register your Machine – Return your Warranty Registration Card!
Serial No:
FMU-2000 High-Speed Burnisher
2000 RPM
Fully Adjustable
Balanced Design
All Metal Chassis
Quiet Motor
Safe & Easy to Use
REGISTER
YOUR
MACHINE!
Safety, Operation and Maintenance
Manual with Parts List
Please read before use!
High-Speed Burnisher
1.5 HP | 2000 RPM | 20”Apron

(2) BISSELL BigGreen Commercial FMU-2000 Burnisher
Dear Valued Customer,
Congratulations on the purchase of your BISSELL BigGreen Commercial FMU-
2000 High-Speed Burnisher! The world of oor care is becoming more high-tech
and competitive and we strive to provide you with the most innovative products. Our
Burnisher is yet another example of this, bringing a new dimension to oor care and
maintenance with its cutting-edge features, quality and value.
Please review this manual paying careful attention to the Safety Instructions section.
Keep in mind that any unnecessary damage, neglect or abuse of this machine will void
your warranty. You can be condent that simple maintenance will ensure that your
Burnisher provides quality performance for many years to come.
If warranty questions arise, please consult your manual or contact your distributor.
Should you have any questions regarding maintenance, replacing parts or ordering parts,
please call an authorized distributor.
Before you begin using your Burnisher, thoroughly review the Owner’s Manual.
Again, congratulations on the purchase of your BISSELL BigGreen Commercial FMU-
2000 High-Speed Burnisher!
Questions or Comments?
BISSELL BigGreen Commercial
100 Armstrong Road | Suite 101 | Plymouth, MA 02360
Phone: [phone] | Fax: [phone]
www.bissellcommercial.com
Warranty Registration
Mail to:
BISSELL BigGreen Commercial
100 Armstrong Road | Suite 101 | Plymouth, MA 02360
See reverse side for warranty information.
Make a copy of this card for future reference.
2013 © BISSELL BigGreen Commercial. All rights reserved.
Please take a moment to register your machine. Fill out the
information below and mail back to BISSELL BigGreen Commercial
immediately.
The warranty starts on the purchase date by the original purchaser, subject to proof
of purchase. Please immediately register your machine by returning this Machine
Registration Card at the time of purchase. If proof of purchase cannot be identied,
the warranty start date is ninety (90) days after the inventory stocking date at the
distributor’s warehouse.
Machine Model Purchase Date
Motor Type Serial No.
Place of Purchase
Shipped To
Your Name Phone
E-mail Fax
Address Line 1
Address Line 2
City State Zip
Comments:
©2013 BISSELL BigGreen Commercial. All rights reserved. All word marks, logos,product
congurations and registered trademarks are owned and used under the authority of BISSELL
BigGreen Commercial.

BISSELL BigGreen Commercial FMU-2000 Burnisher (3)
2013 © BISSELL BigGreen Commercial. All rights reserved.
Please ll out the following information for your records:
Model No:
Serial No:
Distributor Name:
Distributor Phone No:
Date of Purchase:
FMU - 2000 High-Speed Burnisher
By BISSELL BigGreen Commercial
BISSELL BigGreen Commercial
100 Armstrong Road | Suite 101 | Plymouth, MA 02360
Phone: [phone] | Fax: [phone]
www.bissellcommercial.com
New Equipment Warranty
5-year warranty on motor and chassis. 1-year warranty on service labor.
Limited Warranty
The manufacturer gives you the following limited warranty for this product if it was originally
purchased for use, not resale, from BISSELL BigGreen Commercial or a BISSELL BigGreen
Commercial-Authorized Retail Dealer.
The manufacturer will repair or replace, free of charge, to the original purchaser, any part which is
found to be defective in material or workmanship within one (1) year of the date of purchase; ve
(5) years on the motor and gear box.
Drive belts, brushes, and other parts subject to normal wear are not covered by this limited
warranty. This limited warranty does not apply to any part subjected to accident, abuse, or
alteration, misuse, damage caused by re or act of God, the use of voltages other than indicated
on the serial number plate of this product or service of this product by other than a trained service
technician.
The manufacturer does not authorize any person or representative to assume or grant any other
warranty obligation with the sale of this product.
The manufacturer’s limited warranty is valid only if you retain proof of purchase from BISSELL
BigGreen Commercial or a BISSELL BigGreen Commercial-Authorized Retail Dealer for this
product. If you purchase this product from any other source, your purchase is “AS IS,” which
means the manufacturer grants you no warranty, and that you, not the manufacturer, assume the
entire risk of the quality and performance of this product, including the entire cost of any necessary
servicing or repairs of any defects.
The manufacturer’s liability for damages to you for any costs whatsoever arising out of this
statement of limited warranty shall be limited to the amount paid for this product at the time of
original purchase, and the manufacturer shall not be liable for any direct, indirect, consequential or
incidental damages arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE
LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,
WHETHER
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so the above limitation
may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary from
state to state.
©2013 BISSELL BigGreen Commercial. All rights reserved.
All word marks, logos,product congurations and
registered trademarks are owned and used under
the authority of BISSELL BigGreen Commercial.

(4) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (13)
8.0 Machine Parts List
Drawing No. Description Part No. Qty.
46 Drip Cap Mount Screw B-151 6
47 66 Fr. Drip Cap Cover M-242 2
48 66 Fr. Drip Cap Cover Bumper - Green M-239-G 2
49 UHS Motor Screen SCR-01 1
50 UHS Motor Screen Bumper - Green M-238-G 1
51 Cork Drip Cap Gasket M-248 2
52 1.5 HP, DC Motor MOTOR-DC-IMP 1
53 Washer B-28 2
54 Motor Mount Bolt for UHS Motor B-143 2
55 Bearing Block Assembly Mount Bolt B-144 4
56 Bearing Block Assembly BBA-1 1
57 Bearing Block Gasket B-145 1
58A 19” Base Casting A-131 1
58B 20” Base Casting A-132 1
59 Motor Mount Lock Nut B-150 4
60 Bumper - Green BUMPER STOCK 1
61 Ground Wire Screw B-68 2
62 20” Floppy Disk Driver DC-20 1
63 Big Mouth Retainer PR7-ABL 1
64 Screw B-95 4
65 Bolt B-149 1
66 Pulley Driver PD-1 1
67 Bumper Screw B-68 3
68 Bumper Strap BUMPER STRAP 1
69 Drive Belt DC-2000 DB-1 1
70 Allen Head Set Screw For PD B-148 2
71 Pulley To Fit Motor 2000 RPM DC PM-1 1
72 Cotter Pin Wheel Axel B-142 2
73 Spring Washer B-51 4
74 Wheel Axel B-16 2
75 6” Operating Wheel M-250 2
76 Transport Wheel Axel Bolt B-26 2
77 4” Transport Wheel M-209 2
78 Lock Nut B-77 2
79 Front Wheel Assembly FCA-1 1
(2000 RPM Models Only)
1.0 Safe Operating Conditions
READ THIS MANUAL BEFORE USING BURNISHER. KNOW THE PROPER
OPERATION, CORRECT APPLICATIONS AND THE LIMITATIONS OF THIS
EQUIPMENT BEFORE USE.
Reduce the Risk of Fire, Electric Shock or Injury:
• This burnisher is designed for indoor use only. Do not
use outdoors. Do not expose to rain.
• Donotwashthemotorwithowingwater.Ifthemotor
gets wet, seek authorized service.
• Keep the vents on this air-cooled motor free from debris.
Do not operate with the motor covered or with vents
blocked.Donotusethismachineasaoorsander.
• Neveroperatethismachinenearammabledusts,liquids
orvapors.Neveruseammablesolventsasacleaning
agent.Enginesparksandoperatingheatcancausere.
• Neverhandleelectricalequipmentwithwethands.Never
operate this machine with bare feet.
• Unplug the machine when not in use and when servicing
theequipment.Tounplug,grasptheplugnotthecord.
• Do not operate a burnisher with damaged handle
controls,cordorplug.Iftheequipmentisnotperforming
properly,seekrepairfromaqualiedservicesupplier.
• This machine is constructed with electrical grounding
at the plug. Operate only when connected to a properly
grounded outlet. See section 1.2 for grounding details.
• Prevent electrical cord abuse. Do not close a door upon
thecord,driveequipmentoverit,orruntheBurnisher
over it. Do not expose the cord to hot surfaces. Do not
lift, pull or carry this burnisher by the cord.
• Never operate the machine over sharp objects that can be
thrownoutandharmtheoperatoranddamagetheoor.
Sweephardoorsbeforescrubbingorbufng.Vacuum
clean carpets before shampooing or bonnet cleaning.
• Train your staff in proper use of this machine.

(12) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (5)
7.0 Machine Schematic Drawing 2.0 Grounding Instructions
DANGER: IMPROPER GROUNDING METHOD CAN RESULT IN A RISK OF
ELECTRIC SHOCK.
Electrical equipment must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical current and reduces the risk
of electric shock. The vacuum is equipped with a cord containing a grounding conductor
and grounding plug. The plug must be inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
If repair or replacement of the cord or plug is necessary, DO NOT connect the grounded
wire to a at bed terminal. The green insulated wire, with or without yellow stripes, is the
grounding wire.
The BISSELL BigGreen Commercial High-Speed Burnisher operates on a 10.8 amp
nominal 115V, 60 Hz, A.C. power circuit (motors may be custom wired at the factory
220V, 50 Hz international operation). The, amp, hertz and voltage ratings are listed on the
motor spec label found on each Burnisher. Using voltages above or below those indicated
on the spec label will damage the motor. Always check your local voltage requirements.
This Burnisher is for use on a normal 120 volt circuit. It has a grounded plug that ts the
outlet illustrated in Figure A. If a properly grounded outlet is not available, a temporary
adapter, such as the adapter illustrated in Figure B and C, may be used to connect the
plug into a 2-pole outlet, as shown in Figure C.
The temporary adapter should be used only until a properly grounded outlet, Figure A,
can be installed by a qualied electrician. The green color rigid ear lug or grounding
means extending from the adapter must be connected to a permanent ground, such as
a properly grounded outlet box cover. Whenever the adapter is used, it must be held in
place by its grounding means and a metal screw, as shown in Figure C.
WARNING:
Improper connection of the equipment grounding conductor can result in a risk of electric
shock. Check with a qualied electrician or service person if you are in doubt as to
whether the outlet is properly grounded. DO NOT modify the plug provided with the
equipment. If it will not t into the outlet, have a proper outlet installed by a qualied
electrician.
The BISSELL BigGreen Commercial High-Speed Burnisher is built with a 50 foot (15
M) safety cord which plugs directly into an approved outlet. Use of extension cords
is NOT RECOMMENDED. NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electrical Code. This adaptor may not be used in Canada.

(6) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (11)
6.0 Handle Parts List
Drawing No. Description Part No. Qty.
1 Switch Box Back Cover A-104 1
2 Handle Tube Screw B-23 2
3 Switch Box Closing Screws B-21 4
4 Strain Relief Clip M-213 1
5 Switch Plate Screw B-68 2
6 Black Hand Grip with Green Band M-218-G 2
8 Handle Tube Insert M-247 1
9 Handle Tube Assembly M-206 1
10 Cable Hook Screw B-2 2
11 Cable Hook A-164 1
12 Sliding Collar A-111 1
13 Flat Washer B-37 1
14 Split Washer B-39 1
15 Cam Lock Wing Nut B-25 1
16 Straight Brace M-233 2
17 Stop Nut B-10 2
18 Washer B-28 2
19 Cap Screw B-9 2
20 Yoke Tube Mount Bolt B-18A 2
21 Tube Mounting Nut B-19 2
22 Yoke A-1001 1
24 Yoke Bolt B-14 1
25 Handle Tube Cable G-16 1
26 Black Rubber Cable Connector M-249 1
27 Cable Grommet B-63 1
28 Rectangular Hole Cam Washer B-67 1
29A Cam Assembly C-100 1
29B Complete Cam Assembly Kit CCA 1
(Includes 1 each of Drawing Items
#13, 14, 15, 28, 29)
30 50-Foot, 14/3-Gauge - Yellow G-14-50-Y 1
31 Insulated Flag Wire Connector G-48 2
32 On/Off Switch and Plate Assembly G-30-AB 1
33 Switch Mounting Plate G-30-B 1
34 Ground Wire Screw B-1 2
35 Int. Tooth Lock Washer B-35 1
36 Flat Hex Nut B-33 1
37 Trigger Return Spring G-30-C-T057 1
38 Label - Switchbox 1
39 Switchbox Front A-103 1
40 Wire Nut G-47 1
41 Triggers A-105 2
42 16” Crossbar M-211-A 1
43 Trigger Pins B-70 2
44 Cross Bar Screw B-22 2
45 Safety Interlock Assembly SIA-1R 1
1. Mount the handle to the chassis:
Align the handle with the yoke (1) over the mount
(2) on the burnisher chassis. The power cord will be
facingawayfrothemotor.Placeaatwasher(4)on
a 3” bolt (3), then place the bolt through the holes
in the yoke and the mount. Place another washer on
the bolt and secure with the locking nut (5). Tip the
handle back and out of your way for the next step.
2. Mount he support braces on the handle:
Tip the handle up. The handle mounting collar (7)
is designed to slide freely up and down the handle
tube, allowing the handle to be adjusted for the
comfortable operation of all users. Line up the
mounting collar with the upper holes in the two
straight handle braces (6).
• Placethecurvedspacer(12)withasquarehole
onto the locking lever shaft (11). The curve
must face the lever.
• From behind the machine, insert the shaft
through the right handle brace (6), the
mounting collar (7) and the left handle brace.
• Place a spacer (9) on the shaft.
• Place the split washer (13) on the shaft.
• Place the locking wing nut (14) on the shaft.
• Adjust the wing nut for tightness. When
correctly installed, the collar slides easily
when the cam-engineered locking lever is
“up,”butisrmlyxedwentheleveris
“down.”
2.0 Mount the Handle
This burnisher is shipped from the factory with the handle unattached. You will need two
7/16” wrenches to complete the assembly.
Remove the handle and mounting hardware from its carton. Bolts, nuts, washers and the
locking lever assembly are in the plastic bag attached to the handle.

(10) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (7)
5.0 Handle Schematic Drawing 2.1 Attach the Power Cord
The triple-wire grounded power cord has been factory-
installedintothehandletube.Aexiblerubbercable
connector (11) is used to secure the plug-in connections.
The burnisher ships with this connector mounted on the cord
coming out of the handle (10).
Stretch the connector and slip the male connector (9)
(coming out of the motor housing) through the connector
hole and then into the female connector. Now, plug the end
ofthe50-footcordintoagroundedpoweroutlet.Squeeze
the triggers on the handle and check for power to the motor.
2.2 Inspect the Pad Driver
Aexible,high-speedpaddriverhasbeenboltedontotheburnishingmachineand
dynamically balanced. This driver is the connection between the burnisher and a
disposablepadthatburnishesthehardoornish.Ifthismoldedplasticpartever
becomes damaged or if the molded hooks are worn
and cannot hold the pad, replace promptly.
Unplug the burnishing machine. Lock the handle
in the “up” position and tip the machine back fully.
Remove the 4 mounting screws (11) and washers
(12) from the drive hub (13).
Place the new pad driver (14) onto the main drive
pulley. Insert the mounting screws (11) through the
washers (12) into the bolt hole. Tighten securely.
2.3 Install the Pad
The face (bottom) of the pad driver (14) is covered with small “hooks” that grab onto the
pad (16). Every time you mount a new pad onto the pad driver, follow these steps:
• Unplug the burnishing machine. Lock the handle in the “up” position and tip the
machine back fully.
• Pad Sizes: 20” diameter pad on the 20” and 21”
machines. Mount a pad (16) over the male shoulder
(15) on the pad driver. Make sure that the pad is
centered on the driver.
• Insert the locking ring (17) through the center hole in
the pad and into the shoulder. Tighten until the locking
ring lies below the face of the pad. If the ring is not
fullylocked,itwillscratchtheoor.
NEVERoperatetheburnisherwithoutapad.
NEVERoperatetheburnisherwithadamagedpadofwithoutalockingringtoholdthe
pad in place.

3.2 Transport
To transport this burnisher from the janitor’s closet to
the work area:
• Lock the handle in the “up” position. Wind the
cord around the handles and the bottom cord
hook.
• Tip the machine back onto the transport wheels.
Push or pull the machine by the handle, not by
the cord or any other part of the machine. Travel
carefully.
4.0 Troubleshooting
Neveroperatethisburnisherwhentheequipmentisnotperformingasexpectedor
when any parts are visibly damaged. The cause and solution for some basic problems
aredescribedbelow.Whenrepairisneeded,taketheequipmenttoanauthorizedrepair
service center.
4.1 Burnisher will not Run
• Circuit breakers are tripped in the building. Check and reset.
• Equipmentisunplugged.Check plug wall and at machine base. Plug in.
• Power cord failure. Test with a working power cord. Lock the handle up and tip the
motor back. Unplug the cord at the motor and plug the motor into your working
power cord.
• IMPORTANT! THIS IS JUST FOR TESTING. When you do this, you have removed
the safety handle controls from the circuit and you are sending power directly to the
motor. If the motor now spins, the problem is in the cord of the handle assembly.
Seek authorized repair service.
• If the motor still does not spin, the problem is either in the male connection at the
motor base or in the motor. Seek authorized repair service.
• Motor sparks or smokes. Seek authorized repair service.
4.2 Electrical Shock to Operator
• Equipmentwiringfailureorelectricalshortinthemachine.Seek authorized service.
• Poor grounding or no grounding. Test the outlet with a ground fault interrupter.
Retain certied electrician to inspect and repair grounding. NEVER clip off the
ground plug on your cord.
• Repeated circuit breaking. High amp draw and circuit breaking can be an electrical
or mechanical problem. Seek authorized repair service.
4.3 High Vibration
• Pads are not centered on the pad driver. Tip machine back and re-center the pad.
• Uneven wear or warp to pad or brushes. Replace.
• Machine chassis is damaged by dropping. Replace.
(8) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (9)
2.4 Adjust the Front Wheel Assembly on 2000 RPM Model
The 2000 RPM model is designed with a front wheel
assembly that controls the down pressure that the pad
appliestotheoor.Raisetheapronheighttoreducethe
down pressure. Lower the apron height as the pad wears.
The warranty on a 2000 RPM machine will be voided if the
machine is operated without this wheel assembly in place
and operating correctly.
3.0 Operating Tips
• For indoor use only. Sweep abrasive soils before burnishing.
• While the pad driver is spinning, keep the burnisher moving to
avoid“donut”burnsontheoor.
To Start Operation:
• Unlock the handle by raising the locking lever.
• Lower the handle to a comfortable position, typically waist high.
• Relockthehandlebypushingtheleverdown.NEVER
OPERATE THE MACHINE WITH THE HANDLE
UNLOCKED.
• Thisburnisherhasahightorquemotor.
• Holdthemachinermlywithbothhandswhenstartingup.
• Push the red safety interlock switch forward to unlock the dual
triggers.
• Squeezebothtriggerstopowerthemotor.Oncepowerison,
either trigger will keep power to the motor. To stop, release both
triggers.
3.1 To Store your Machine
• Lock the handle in the “up” position. Tilt the machine
back onto the transport wheels. Never store the machine
with the pad on the ground.
• Wind the cord around the handles and the bottom cord
hook.
• Wash pads and hang to dry.
• Inspectandmaintainequipmentonaregularschedulefor
best results.
• Check and clean pads after each operation. Remove soil
and chemical buildup. Replace worn or damaged pads.
• Check the triggers and switches for proper operation.
• Use air pressure or vacuum to remove dust and debris
from the motor vents.
• Report problems and repair promptly.