Bitspower TITAN X 2.0 User manual

Parts List
— 1—
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
English
TITAN X_2.0 Installation Guide
BPTA-O11D-AK_AMD_A2.0-BK
B-1 B-2
A-1
※The allowable variance in tube length is ± 2mm
252
63
Fittings
B
.................2 pcs
BPTA-DOTFH1622
B-1
....................2 pcs
BPTA-15ATFH16
B-2
Accessory
C
................................2 pcs
Hard tube
C-1
....................1 pc
Fitting + soft tube
C-2
A
B
C
CPU set
C-3
Hard Tube
C-1
Fitting + soft tube
C-2
V3
Thumb screw
SPRING
Thumb nut
1mm Spacer
M3x32mm Screw
SC6-32M3
Nylon cup washer
Φ:16
CPU Water Block
A
..........1 pc
BPTA-CPUMS-V2-SKA
A-1

I. AMD Motherboard system
— 2—
96 90
48
54
AMD SOCKET AM4 AMD SOCKET AM3 / AM3+ AMD SOCKET AM2 / AM2+ AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
DRGB LED
IN
OUT
DRGB PIN on Motherboard or other equipment.
 
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
SCM3FL20
CPU Block
SPRING
1mm SPACER
Installation
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
SCM3FL20
SPRING
CPU Block
1mm SPACER
SCM3F6
EX.
Do not over-tighten the thumb screws
(SCM3FL20). The springs should be
slightly compressed, with visible gaps
in the spring coils. Over-tightening
may result in poor contact between the
water block and CPU.
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
(Pre-installed with
ASUS X570-E
AM4 Motherboard)
ASUS X570-E AM4 Motherboard and
EVGA 850 Watt Power Supply has
been Installed on TITAN X A1.2.
Check your AMD Accessory box for original
Motherboard brackets and screws.
This step has already
been assembled for
AMD Motherboard
installation.
Titan One 2.0 is compatible with most motherboards.
If not compatible, please contact Bitspower directly,
thank you.

— 3—
PUMP HEADER
②FULL SPEED
AIO_PUMP
PUMP HEADER
① PWM CONTROL
CPU_FAN
II. AMD Chipset Installation
Step 1
Step 2
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
227~240mm
Hard tube BPTA-15ATFH16
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
After the hard pipe is installed, please keep the
total length between 227-240mm to ensure
that the waterway will function properly.

— 4—
Pour the coolant into the reservoir via the water filling hole. Once the reservoir is 90% full,
turn on the power supply for the pump to run and let the air exit the loop. Turn off the
power supply when the reservoir is near empty. Repeat until all the air has exited the loop.
Notice : Do not turn on the pump if the reservoir is empty.
Bitspower recommends that consumers add the Bitspower coolant or
purified water for their water-cooling liquid. If the consumer chooses
different water-cooling liquids , the resulting impurities may cause
peeling of the coating on some of the hardware, water channels block-
age by built-up residue, improper operation of the water pump, water
tank tube breakage, and o-rings deformation leading to leakage. Any
issues related to the use of inappropriate water-cooling liquid will be
the responsibility of the consumer.
In order to make the internal circulation of the water cooling system
cleaner, and avoid the pump stuck by the precipitate, we advise you to
rinse the water cooling system with distilled water in several times until
the excluded water is clean.
BPTA-EFW
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
Step 1
Unscrew the top of the water-exhaust fitting.
AIO_PUMP
PUMP HEADER
① PWM CONTROL
CPU_FAN
PUMP HEADER
②FULL SPEED
AIO_PUMP
CPU_FAN
A Negative electrode -
B positive electrode +
C Speed signal
A B C D
Step 2
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
III. BPTA-WDPO11D-AK-LITE
Pump Spec.
Rated voltage：12V DC
Power consumption：8.4W
Maximum flow：460±15%L/h
Noise：≦24dBA
PWM：Yes
MTBF：≦15,000 hours
Warranty：2 years
Water filling hole
90% full