Bitspower O11DXL User manual

[ 1 ]
instruction manual
Digital RGB PIN on 1motherboard or 2other equipment.
motherboard DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
Accessories
1M3x8 Screw 2 PCS
Bitspower Sedna O11DXL for LIAN LI O11
DYNAMIC (Hercules Pump, Front ver.) V1
BPTA-TOO11DXLA-PHCL
Both the front and the back side of the reservoir have a 󽗉ll or
drain hole, choose the one that suits you.
Fill
Drain
2M4x25 Screw 3 PCS 3Base 1 PCS

[ 2 ]
Power Supply and Pump
SPECIFICATION
Rated voltage：12V DC
Power consumption：15W
Maximum 󽗊ow：11±15% L/min
Noise：≤ 40dBA
PWM：Yes
MTBF：15000 hours
Warranty：2 years
Dimension: 62 x 62 x 46.7mm
Maximum lift of the water pump: 5.5±0.5m
※ The position of the Hole position o󽗈set block can
be adjusted to correspond to the CPU installation
position of di󽗈erent motherboards.
※Recommended：BPTA-SCT-WD
If need be
O-Ring(54×50×2)
Water conduit modules
Hole o󽗈set block(CPU)
M4×16mm Screw
O-Ring(60×56×2)
※When installing the GPU, it is necessary to
remove the conduit module, and then install the
corresponding 󽗉ttings.
G1/4 Screw plug
All tube connect hole sare G 1/4
threaded holes.

[ 3 ]
Water
Choose your desired dye color and mix it with pure
distilled water. Pour the water mix into the reservoir
via the water filling hole. Once the reservoir is 90%
full, turn on the power supply for the pump to run
and let the air exit the loop. Turn off the power
supply when the reservoir is near empty. Repeat until
all the air has exited the loop.
(In order to power the pump only, connect the power
switch connector to the 24 pin cable of the power
supply. This will allow the power supply to bypass
the motherboard and make the pump work alone.)
The warranty will be void if any of the situations below happen.
Water Block
- The CPU block and the screws in it has any trace of disassemble.
- The top plate inlet and outlet ports, due to improper use of external forces, are cracked.
Radiator
- The 󽗉n of the radiator are broken or deformed due to improper use of external forces.
- The inlet and outlet of the radiator are cracked due to improper use of external forces.
Fitting
- There are signs of damage caused by instrument clamping on the 󽗉ttings.
PUMP
- Pump damage from pump operation without any liquid.
- Pump damage caused by water leak on the pump's PCB.
- Water tank has been separated from the pump.
Fan
- Fan damaged by water leak.
G1/4 Screw plug
- If the plug, screw speci󽗉cation or thread are not up to standard, the screw can not be
locked. If you tighten the screw violently, the device will be damaged.
Product Warranty Rules
Not included

[ 4 ]
Assembly steps
step 1
step 4
step 3
step 2
LIAN LI O11 DYNAMIC XL
(Not included)
M3x8 Screw
TOP
Front plateSide plate

[ 5 ]
M4x25 Screw
Accessories(additional purchases)
Recommended installation method
BPN-NLS360-F2PB
BPTA-CPUMS-SKI
BPTA-FX1812NT-3
BPTA-DOTFH1622
A
B
C
D
2 PCS
1 PC
2 SETS
12 PCS
BP-NCCLT16AC-L500
E
A
B
C
D
E
step 5
A
C
E

[ 6 ]
記得上角要放對應的 LOGO!
Notice
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it
will be the fault of the customer. DO NOT use the leak teser when there is
water in the loop or the pump is running.
Bitspower recommends that customers use Bitspower Pellucid Coolant
for their coolant fluid. It is also recommended to use Bitspower Dye to
create any desired color. If the customer chooses di󽗈erent liquid coolants,
the resulting impurities may cause peeling of the coating on some of the
hardware, water channel blockage by built-up residue, improper operation
of the water pump, water tank tube breakage, and o-ring deformation
leading to leakage. Any issues related to the use of inappropriate liquid
coolants will be the responsibility of the customer.

[ 7 ]
記得上角要放對應的 LOGO!
使用說明書
配件
請接 1主板或 2 其他設備的 DRGB 插槽
主板
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
Bitspower Sedna O11DXL for LIAN LI O11
DYNAMIC (Hercules Pump, Front ver.) V1
1M3x8 螺絲 2 PCS
BPTA-TOO11DXLA-PHCL
水道板上前後都有預留進水和排水的孔位，請視情況擇一選用
即可。
進水
2M4x25 螺絲 3 PCS 3底座 1 PCS
出水

[ 8 ]
供電與水泵
如果有需要
※ 可通過調整孔位偏移塊的位置，以對應不同主機板的
CPU 安裝位置。
※ 安裝 GPU 冷頭時，需要把水路導通模組拆除，然後安
裝相應的接頭即可使用。
SPECIFICATION
Rated voltage：12V DC
Power consumption：15W
Maximum 󽗊ow：11±15% L/min
Noise：≤ 40dBA
PWM：Yes
MTBF：15000 hours
Warranty：2 years
Dimension: 62 x 62 x 46.7mm
Maximum lift of the water pump: 5.5±0.5m
※ 建議：BPTA-SCT-WD
O 圈 (54×50×2)
水路導通模組
孔位偏移塊 (CPU)
M4×16mm 螺絲
O 圈 (60×56×2)
G1/4 堵頭
所有接管孔位為 G1/4 螺牙孔

[ 9 ]
注水
選擇喜好的水冷濃縮液顏色，以純淨水調合，由”填水孔”
注入至水箱九分滿，接著利用”24PIN 跳線開關”啟動電源，
讓水路中的空氣集中至水箱排出，再依水量繼續添加至
水箱九分滿左右即可。
（24PIN 跳線開關用途：需無經主板開啟 ATX 電源時，使
電源直接開啟供電。）
質保期時效，送修的產品凡有以下狀況，不在保修範圍內。
水冷頭
- 冷頭自體螺絲，有拆裝痕跡，整套產品失保。
- 頂部的進出口，因為外力使用不當導致開裂。
冷排
- 因為外力使用不當導致冷排水道破裂漏水。
- 進出水孔因為外力使用不當導致開裂。
接頭
- 有器械夾持導致的損傷痕跡。
水泵
- 無水通電導致水泵燒毀。
- 底部 pcb 進水燒毀。
- 水箱底座與水泵不可拆解，一經拆解即不保固。
風扇
- 進水燒毀。
堵頭
- 堵頭、螺絲規格或牙紋不達標，會鎖不了孔位，暴力裝配致使破裂。
產品保修規範
未包括

[ 10 ]
組裝步驟
步驟 1
步驟 3
步驟 2
步驟 4
LIAN LI O11 DYNAMIC XL
( 不包括 )
M3x8 螺絲
上蓋
前面板側面板