Black Box EMERALD PE SH User manual

STEP X - Name of Step
24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM
EMD2000PE-T, EMD2000PE-R-P, EMD2000PE-K
EMERALDEMERALD
PE SHPE SH
QUICK START GUIDE

STEP 1A - Transmitter Diagrams
1 2
3 4 5 6 7 8 9 11 12 13
10

STEP 1B - Transmitter Components
TABLE 1. EMD2000PE-T COMPONENTS
NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION
1 Power LED Lights when power is ON
2Micro USB connector For future use
3 12 VDC Power In connector Connects to supplied power adapter
4 TP port Speed LED Indicates 10/100/1000 Mbps
5 RJ-45 PoE port Connects to network and supports
Power over Ethernet (PoE)
6 TP port Activity LED Indicates activity on the link
7 USB Type B connector Connects to PC/workstation USB
connector
8 Fiber port Speed LED Indicates 10/100/1000 Mbps
9 Fiber port Activity LED Indicates activity on the link
10 SFP cage Holds fiber network SFP module
11 DVI Video connector Connects to PC Video
12 Audio Line In Connects to speakers
13 Audio Line Out Connects to microphone
NOTE: Unit automatically powers on when plugged in; must be powered off at the power source.

STEP 2A - Receiver Diagrams
1 2 3 4 5
6 7 8 9 10 11 12 14
13

STEP 2B - Receiver Components
TABLE 2. EMD2000PE-R-P COMPONENTS
NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION
1 Power LED Lights when power is ON
2Micro USB connector For future use
3 (2) USB Type A connectors Connect to USB peripherals
4Microphone Connects to microphone
5Speakers Connects to speakers
6 12 VDC Power In connector Connects to supplied power adapter
7 TP port Speed LED Indicates 10/100/1000 Mbps
8 RJ-45 PoE port Connects to network and supports
Power over Ethernet (PoE)
9 TP port Activity LED Indicates activity on the link
10 (2) USB Type A connectors Connect to USB peripherals
11 Fiber SFP port Speed LED Indicates 10/100/1000 Mbps
12 Fiber SFP port Activity LED Indicates activity on the link
13 SFP cage Holds fiber network SFP module
14 DVI Video connector Connects to monitor
NOTE: Unit automatically powers on when plugged in; must be powered off at the power source.

STEP 3 - Install SFPs in the SFP cages
INSTALL AN SFP MODULE IN THE TX
1. Plug a compatible SFP in the SFP slot on the
transmitter unit (TX).
NOTE: See Table 3 for a list of compatible
SFPs (ordered separately).
INSTALL AN SFP MODULE IN THE RX
1. Plug a compatible SFP in the SFP slot on the
receiver unit (RX).
NOTE: See Table 3 for a list of compatible
SFPs (ordered separately).
TABLE 3. COMPATIBLE SFPS
PART NUMBER DESCRIPTION DISTANCE
1-Gbps Connections
LFP441 SFP, Gigabit Ethernet, 850-nm Multimode Fiber, LC 550 m
LFP442 SFP, Gigabit Ethernet, 1310-nm Singlemode Fiber, LC 20 km
LFP443
SFP, 10/100/1000BASE-T RJ-45 SGMII
100 m
LFP411
SFP, 1.25-Gbps, 850-nm Multimode Fiber, LC
550 m
LFP413
SFP, 1.25-Gbps 1310-nm Singlemode Fiber, LC
10 km
LFP414
SFP, 1250 Ext. Diag. 1310-nm Singlemode Fiber, LC
30 km
LFP415
SFP, 1.25-Gbps Copper RJ-45, SerDes
100 m
LFP416
SFP, 1250 Ext. Diag. 10/100/1000 RJ-45 SGMII
100 m
NOTE: The EMD2000PE-K kit contains one TX (EMD2000PE-T) and one RX (EMD2000PE-R-P).

STEP 4A - Connect Power via External Power Supply
CONNECT POWER TO TRANSMITTER
1. Locate the power supply adapter and the AC
line cord.
2. Plug the DC connector of the power supply
into the matching socket on the rear of the
transmitter.
3. Attach the AC line cord to the power supply
adapter.
CONNECT POWER TO RECEIVER
1. Locate the power supply adapter and the AC
line cord.
2. Plug the DC connector of the power supply
into the matching socket on the rear of the
receiver.
3. Attach the AC line cord to the power supply
adapter.
CONNECT POWER USING POE
1. Connect all computer cables to the
Transmitter.
2. Plug the POE enabled network cable into the
transmitter; power will be enabled immediately.
3. Connect the monitor and peripheral devices
into the receiver.
4. Plug the POE enabled network cable into the
receiver; power will be enabled immediately.
STEP 4B - Connect Power via PoE

STEP 5 - Connect the Peripherals
CONNECT THE TRANSMITTER
1. Attach the Emerald PE Transmitter to the
target PC/workstation using DVI and USB Type
B cables.
2. Connect to the LAN using standard CATx
UTP or fiber cables to the local network
connection.
CONNECT THE RECEIVER
1. Attach the monitor, keyboard, mouse, USB
and audio devices to the Emerald PE Receiver.
2. Connect to the LAN using standard CATx
UTP or fiber cables to the local network
connection.

STEP 6 - Starting Up and Default Settings
STARTING UP
1. Once everything is connected, the unit
automatically powers on when it is plugged
in via a power adapter or PoE.
2. The Graphical User Interface (GUI) will
appear on the screen.
3. Enter the default administrator user name
and password.
User name: admin
Password: blank (just press the Enter key)
4. The default network setting for the Emerald
PE Receiver uses a preconfigured static IP
address.
5. If you require the unit to be set to use DHCP,
select the Control tab on the GUI and then
choose the Network option. Select the DHCP
option and click Apply.
DE FAULT SETTINGS
Default Settings:
Transmitter IP Address: 192.168.1.22
Receiver IP Address: 192.168.1.21
Type: Static
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
Admin username: admin
Admin password: no password, it is blank by
default
Ports Used: 3389
IMPORTANT: Do not lose the admin password
once configured; there is no way to reset or
retrieve it. The Emerald PE receiver has the
option to create a second administrator account
as a secondary entrance.

STEP 7 - Point-to-Point Installation
POINT-TO-POINT INSTALLATION
In a point-to-point configuration, no
administrator setup of the Emerald PE
Transmitter or the Emerald PE receiver is
required. This enables you to install the
system quickly, directly out of the box. In the
point-to-point configuration, you can install
only one transmitter and receiver pair on a
subnet and both must be on the same subnet
unless a router is present in the network
to span subnets. To span across different
subnets, you will need to have admin rights to
both routers on either side of the installation
and setup port forwarding for port “3389”
for Remote Desktop.
If further configuration is required to change
the default IP addresses, you can access
the transmitter’s network settings through
the remote unit:
1. Simply connect the transmitter to the receiver
using a CATx cable (but do not power up the
transmitter yet), then connect a keyboard,
monitor, and mouse to the remote unit (remote
unit is on at this time).
2. Login as “admin” and go to (Control)>>
(Transmitter)>> (Discover) and follow the
on-screen steps.
3. It will advise you to connect both devices
together and then power up the transmitter
and press the “Next” button.
4. It will take several minutes to discover
the transmitter, but once found, you can modify
the network parameters.

STEP 8 - Matrix Installation and Getting Started
MATRIX INSTALLATION
In a matrix installation, every Emerald PE
transmitter and receiver requires its own IP
address. By default, the DHCP setting is set
to static, so the addresses will need to be
configured manually:
1. Always configure the transmitter first by
connecting the transmitter to the receiver
using a CATx cable (but do not power up the
transmitter yet), then connect a keyboard,
monitor, and mouse to the remote unit (remote
unit is on at this time).
2. Login as “admin” on the remote unit and
go to (Control)>> (Transmitter)>> (Discover)
and follow the on-screen steps.
3. It will advise you to connect both devices
together, and then power up the transmitter
and press the “Next” button.
4. It will take several minutes to discover the
transmitter, but once found, you can modify
the network parameters.
5. Once the transmitter is configured, you can
now configure the receiver.
6. If the units are on different subnets,
then routers will need to be used to properly
direct traffic.
GETTING STARTED
Once the IP addresses have been configured,
each receiver will need to be configured for
users, user passwords, user access rights
and default video resolutions. You can access
these settings from the receiver’s OSD (reboot
the receiver and login as admin) and begin
configuring these parameters.
NOTE: Each receiver can support a maximum
of 32 users and a maximum of 32 targets
(virtualized or transmitter).

STEP 9 - Download the User Manual (Optional)
The full user manual/installation guides
can be downloaded from the Black Box Web site.
FOR US, AUSTRALIA NEW ZEALAND, AND
CANADA
1. Go to BLACKBOX.COM
2. Enter the part number in the search box
(for example, EMD2002PE-T).
3. Click on the product in the “Products” page.
4. Click on the “Support” tab on the product page
and select the document you wish to download.
FOR OTHER COUNTRIES
1. Go to BLACK-BOX.EU/SUPPORTCENTER
2. Enter the part number in the search box and
check the le type: application diagram, data-
sheet, rmware or manual.
3. Select the document you want to download.

NOTES

NOTES

STEP X - Name of Step
COPYRIGHT 2021. BLACK BOX CORPORATION. ALL RIGHTS RESERVED.
EMD2000PE-T_QSG_REV3.PDF
Contact our free, 24/7 technical support in the US at 877-877-2269
or [e-mail]
For other countries, go to BLACKBOX.COM/CONTACT-US

NOTES