Black Box LPS500A-MM-LC-R2 User manual

24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM
10/100/1000B-T
TO 1000B-X POE
PSE GBE MEDIA
CONVERTER
USER MANUAL
LPS500A-MM-LC-R2, LPS500A-MM-SC-R2, LPS500A-SM-10K-LC-R2
LNK/ACT
LNK/ACT
PWR
4W
7W
15.4
SPD
PoE
FX
PSE-TP
10/100/1000BASE-T PoE PSE To 1000BASE-X
Media Converter
PoE-Power Sourcing Equipment
TX RX
KINSUN

2
TABLE OF CONTENTS
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
CONTENTS
SAFETY INFORMATION.................................................................................................................................................................................. 3
1. SPECIFICATIONS ......................................................................................................................................................................................... 4
2. OVERVIEW..................................................................................................................................................................................................... 5
2.1 INTRODUCTION.......................................................................................................................................................................................... 5
2.2 AVAILABLE MODELS................................................................................................................................................................................. 5
2.3 FEATURES ................................................................................................................................................................................................... 5
2.4 WHAT’S INCLUDED.................................................................................................................................................................................... 5
2.5 HARDWARE DESCRIPTION ...................................................................................................................................................................... 6
2.5.1 FRONT PANEL ......................................................................................................................................................................................................6
2.5.2 BACK PANEL.........................................................................................................................................................................................................6
3. INSTALLING THE CONVERTER.................................................................................................................................................................. 7
4. WDM SINGLE FIBER MODEL ...................................................................................................................................................................... 9
5. LINK FAULT PASSTHROUGH ................................................................................................................................................................... 10
6. LED DESCRIPTION..................................................................................................................................................................................... 12
7. DIP SWITCH AND RESET BUTTON.......................................................................................................................................................... 13
8. CABLE CONNECTION PARAMETER........................................................................................................................................................ 14
A.1 ELECTRONIC EMISSION NOTICES ....................................................................................................................................................... 15
A.2 FCC CLASS A STATEMENT...................................................................................................................................................... 15
A.3 NOM STATEMENT..................................................................................................................................................................... 16
B.1 DISCLAIMER.............................................................................................................................................................................. 17
B.2 TRADEMARKS USED IN THIS MANUAL.................................................................................................................................. 17

3
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
SAFETY INFORMATION
SAFETY INFORMATION
CAUTION: Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or
walking across a carpeted floor may cause you to acquire a static electrical charge.
To protect your device, always:
Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device.
Pick up the device by holding it on the left and right edges only.

41. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 1: SPECIFICATIONS
1. SPECIFICATIONS
TABLE 1-1. SPECIFICATIONS
SPECIFICATION DESCRIPTION
Compliance
Standards
IEEE802.3u 10/100BASE-TX, 100BASE-FX
IEEE802.3z/ab 1000BASE-T
IEEE802.3af Power over Ethernet
Certifications FCC Part 15 Class A;
CE Mark
Data Transfer Rate
Speed 1000 Mbps, 100 Mbps, 10 Mbps
Forwarding Rate 14,880 pps, 148,800 pps, 1,488,000 pps
Flow Control
Full duplex IEEE802.3x compliant for full duplex
Half-duplex Backpressure flow control for half-duplex
Cable
UTP CAT5 cable (up to 328 ft. [100 m])
Fiber 50/125, 62.5/125 or 100/140 μm multimode;
8.3/125, 8.7/125, 9/125 or 10/125 μm singlemode
Indicators
LEDs POWER, PoE, TP LNK/ACT, SPD, FX LNK/ACT, 4 W, 7 W, 15.4 W
Power
PSE Supports “Endpoint” via TP pin 1, 2, 3, 6
Power Requirement, AC Line 100 to 240 VAC, 47 to 63 Hz
Power Consumption Max. up to 65 W
Environmental
Operating Temperature 32 to 122° F (0 to 50° C)
Humidity 5% to 95%
Mechanical
Connectors
LPS500A-MM-LC-R2: (1) RJ-45 PoE, (1) pair of multimode LC;
LPS500A-MM-SC-R2: (1) RJ-45 PoE, (1) pair of multimode SC;
LPS500A-SM-10K-LC-R2: (1) RJ-45 PoE, (1) pair of singlemode LC
Dimensions 1.6” H x 6.2” W x 5.2” D (4.0 x 15.8 x 13.3 cm)
NOTE: For connecting this device to a router, bridge, or switch, refer to the corresponding device’s user manual.

5
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 2: OVERVIEW
2. OVERVIEW
2.1 INTRODUCTION
The unmanaged PoE PSE Media Converter is a next generation Ethernet media converter offering one gigabit per second performance.
It is used in Ethernet copper to fiber media conversion applications over long distances.
The media converter delivers one (10M/100M/1G) RJ-45 with one PoE port (supports 802.3af up to 15.4 W) and one GbE SC or LC port.
The converter provides high hardware performance and environment flexibility for Ethernet applications.
2.2 AVAILABLE MODELS
Three models are available:
LPS500A-MM-LC-R2: TP to Multimode Fiber Media Converter with RJ-45 and LC connectors
LPS500A-MM-SC-R2: TP to Multimode Fiber Media Converter with RJ-45 and SC connectors
LPS500A-SM-10K-LC-R2: TP to Singlemode Fiber Media Converter with RJ-45 and SC connectors
2.3 FEATURES
RJ-45 link supports IEEE 802.3ab 1000BASE-T Gbps Ethernet over twisted-pair cable
Fiber link supports IEEE 802.3z 1000BASE-X Gbps Ethernet over fiberoptic cable
Provides IEEE 802.4af maximum 15.4 W Power over Ethernet (PoE)
DIP switch sets PoE, LFP, and normal/cut-through configurations
Power over Ethernet (PoE): The PoE converter provides PoE power and supports various PoE PD device types (IP-phone, IP-camera,
WiFi-AP) for end users to eliminate an extra power cable to these devices
Link Fault Passthrough (LFP): When this is enabled, the UTP receiver is passed to the fiber transmitter to make the media converter
appear transparent to the end devices that are connected. It uses LFP to indicate when far-end fault issues occur. If a fault occurs, the end
devices indicate a failure for troubleshooting.
2.4 WHAT’S INCLUDED
Your package should contains the following items. If anything is missing or damaged, contact Black Box Technical Support
at 877-877-2269 or [e-mail]
10/100/1000BASE-T to 1000BASE-X PoE PSE GbE Media Converter
AC Power Cord

61. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 2: OVERVIEW
2.5 HARDWARE DESCRIPTION
Figures 2-1 and 2-2 show the front and back panel sof the converter. Table 2-1 describes the components.
2.5.1 FRONT PANEL
PSE 10/100/1000Base-TX to 1000Base-X Media Converter
PoE-Power Sourcing Equipment
802.3af Endpoint
4W LINK/ACT
7W
15.4W POE
SPD FDX/COL
PWR
1310nm/1550nm
FX
PSE-TP
12 3 4
FIGURE 2-1. POE PSE MEDIA CONVERTER FRONT PANEL
2.5.2 BACK PANEL
5
FIGURE 2-2. POE PSE MEDIA CONVERTER BACK PANEL
TABLE 2-1. CONVERTER COMPONENTS
NUMBER IN FIGURE 2-1 OR 2-2 SIGNAL DESCRIPTION
1 (1) RJ-45 PoE connector Links to Powered Device (PD)
2 (6) TP LEDs: PoE, TP LNK/ACT, SPD, 4 W, 7 W, 15.4 W Indicates twisted-pair port status
3 (2) FX LEDs: Power, FX LNK/ACT Indicates fiber port status
4
LPS500A-MM-LC-R2 : (1) multimode LC connector:
LPS500A-MM-SC-R2: (1) multimode SC connector;
LPS500A-SM-10K-LC-R2: (1) singlemode LC connector
Links to Gigabit fiber network
5(1) 3-prong power connector Links to 100 to 240 VAC, 47 to 63 Hz power

7
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 3: INSTALLING THE CONVERTER
3. INSTALLING THE CONVERTER
PSE TP-Fiber Converter with Powered Device (PD)
1. Connect the PSE media converter to an AC power source.
2. Install the UTP media cable to the IEEE 802.3af PD converter.
LNK/ACT
LNK/ACT
PWR
4W
7W
15.4
SPD
PoE
FX
PSE-TP
10/100/1000BASE-T PoE PSE To 1000BASE-X
Media Converter
PoE-Power Sourcing Equipment
TX RX
KINSUN
To Gigabit fiber network
To PD device
CAT5
cable
Fiber
cable
FIGURE 3-1. MEDIA CONVERTER CONNECTIONS
NOTE: It can work as a pure converter that connects to the non-PoE converter.
3. Install the media cable for network connection.
WARNING:
Verify that the AC input conforms to your country AC power requirement and then insert the power plug.
Ensure that the power of PSE device is turned on
Install the media cable for network connection
TABLE 3-1. CONNECTOR FUNCTIONS
CONNECTOR FUNCTION
TP Port
10/100BASE-TX:
Auto-Negotiation
Auto-MDIX
flow control for Full-Duplex
backpressure for Half-Duplex
1000BASE-TX:
Auto-Negotiation mode
Auto-MDIX only for Auto-Negotiation
flow control for Full-Duplex only
Fiber Port 1000BASE-SX/LX (SC/LC) with flow control
NOTE: Link partner must be 1000FDX with flow control

81. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 3: INSTALLING THE CONVERTER
PoE PD or
PoE Splitter
TX
1000BASE-X
Fiber Network
Converter/Switch PoE PSE TP-to-GbE
Fiber Converter
TX
RX
RX
FIGURE 3-2. PSE TO PD OR POE SPLITTER
CAT-5 Cable
RJ-45 Connector
Signal Pairs 48V
+
_+
_
8765 4 32 1
FIGURE 3-3. ENDPOINT PSE RJ-45 MALE CONNECTOR
NOTE: IEEE802.3af assigns pairs on the RJ-45 connector and Cat.5 cable of Endpoint PSE.
Endpoint : -48V via TP pin 1, 2, 3, 6

9
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 4: WDM SINGLE-FIBER MODEL
4. WDM SINGLE FIBER MODEL
The TP-Fiber converter is specially designed with an optic Wavelength Division Multiplexing (WDM) model that can transport a
bidirectional full duplex signal over a single fiber simultaneously.
TABLE 4-1. SINGLE-FIBER TX/RX WAVELENGTH
SINGLE-FIBER MODEL TX/RX WAVELENGTH
1310-nm singlemode 10 km TX (Transmit) 1310 nm
RX (Receive) 1550 nm
1550-nm singlemode 10 km TX (Transmit) 1550 nm
RX (Receive) 1310 nm
NOTE: The 1310 nm and 1550 nm models must be installed in pairs, i.e., install 1310 nm model at one end and 1550 nm model at the
other one.
PoE PSE TP-to-GbE Fiber
WDM Single Fiber
TX-1310/RX-1550
TP
TP
PoE PD
TP
TP
PoE PSE TP-to-GbE Fiber
WDM Single Fiber
TX-1550/RX-1310
Single Fiber
FIGURE 4-1. POWER FROM PSE TO PD

10 1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877. 2269
CHAPTER 5: LINK FAULT PASSTHROUGH
5. LINK FAULT PASSTHROUGH
The LFP (link fault passthrough) in a TX/FX converter application is controlled by the software and instantly takes effect. Link status on
one port is propagated to the other port to notice the remote nodes. If the TP port is unplugged, this converter stops transmission on the
fiber port. This causes the remote fiber node link to fail. An LED shows the link failure on both TP and fiber ports. If the fiber link fails, this
converter restarts auto-negotiation on the TP port but always stays in the link failure state. This causes the remote TP node link to fail.
An LED also shows the link failure on both TP and fiber ports. Refer to Figure 5-1 shown below for the normal status when the link
succeeds.
Also refer to Figure 5-2 and Figure 5-3 for the error status when TP Cable A, Fiber Cable B, or Fiber Cable C fails to connect.
NOTE: Link fault pass through (LFP) function only takes effect as S1-Bit2 (see Figure 5-4) is enabled. Disabled S1-Bit2 will turn this media
converter into a general one.
Fiber
Cable
GbE
Switch
GbE
Switch
LFP LFP
Remote
Station
D AB
C
TP TP
FIGURE 5-1. NORMAL STATUS VIA LFP CONVERTER
Fiber
Cable
GbE
Switch
GbE
Switch
LFP LFP
Remote
Station
D AB
C
TP TP
FIGURE 5-2. THE STATUS AS TP CABLE A OR D IS BROKEN
Fiber
Cable
GbE
Switch
GbE
Switch
LFP LFP
Remote
Station
D AB
C
TP TP
FIGURE 5-3. THE STATUS AS FIBER CABLE B OR C IS BROKEN
Fiber
Cable
GbE
Switch
GbE Fiber
Switch
LFP
Remote
Station
AB
CTP
FIGURE 5-4. NORMAL STATUS VIA LFP CONVERTER