Black Box BDS-8-1 User manual

24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM
BDS
TEMPERATURE
KIOSK
QUICK START GUIDE
BDS-8W(-1), BDS-8THA(-1), BDS-8FHA(-1)

2
TABLE OF CONTENTS
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
CONTENTS
STEP 1. CONNECT THE GATE ........................................................................................................................................................................ 3
STEP 2: REVIEW THE PORTS DEFINITION................................................................................................................................................... 3
2.1 WIRE INTERFACE DEFINITION VERSION 1.......................................................................................................................................................3
2.2 WIRE INTERFACE DEFINITION VERSION 2......................................................................................................................................................4
STEP 3. APP INSTRUCTIONS......................................................................................................................................................................... 5
3.1 ENTER THE SETTING INTERFACE......................................................................................................................................................................5
3.2 APPLICATION SETTINGS.....................................................................................................................................................................................6
3.3 FACE IMAGE ACQUISITION..................................................................................................................................................................................7
3.4 APPLICATION INFORMATION: VIEW THE BASIC INFORMATION OF THE DEVICE...............................................................................8
3.5 PASS RECORD .........................................................................................................................................................................................................9
3.6 FACE LIBRARY: INFORMATION OF FACE........................................................................................................................................................10
A.1 DISCLAIMER.............................................................................................................................................................................. 11
A.2 TRADEMARKS USED IN THIS MANUAL ................................................................................................................................. 11

3
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
This quick start guide explains how to install the BDS Temperature Kiosk. Follow the steps listed next.
NOTE: Upon first use, the BDS unit may display inconsistent temperature readings until the unit boots up and the Infrared Sensors warm
up.
NOTE: The BDS supports two languages: English and Chinese. Adding custom language support may require APK and firmware updates
that could potentially take up to one month.
STEP 1. CONNECT THE GATE
Connect the tablet relay cable to the door open button terminal of the gate control board. If the door opening action is reversed, reverse
the line order.
If there is no response, set in the BDS (EZ-Pass) app as follows:
Mode 0: Indicates non-automatic closing mode. The relay will not close automatically after opening the relay.
Mode 1: Represents the auto-closing mode (active high-default low level, then high level for X seconds, last low level). The relay will
automatically close after a delay of X seconds after opening the relay.
Mode 2: Represents the auto-closing mode (active low-default low, then high for X seconds, and finally low). The relay will automatically
close after a delay of X seconds after opening the relay.
STEP 2: REVIEW THE PORTS DEFINITION
2.1 WIRE INTERFACE DEFINITION VERSION 1
12 VDC
USB Host
UBOOT
Wiegand
Output Wiegand
Input
USB OTG
Relay
Ethernet
RS-232
FIGURE 1.
TABLE 1. DELAY
PIN NUMBER TERMINAL ELECTRICAL DEFINITION
1COM
2NO

41. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
TABLE 2. WIEGAND INPUT
PIN NUMBER TERMINAL ELECTRICAL DEFINITION
1D0_IN
2D1_IN
312 V
4GND
TABLE 3. WIEGAND OUTPUT
PIN NUMBER TERMINAL ELECTRICAL DEFINITION
1D0_OUT
2D1_OUT
3GND
TABLE 4. RS-232
PIN NUMBER TERMINAL ELECTRICAL DEFINITION
1232_RX1
2232_TX1
3GND
2.2 WIRE INTERFACE DEFINITION VERSION 2
12 VDC
USB Host
UBOOT
Wiegand
Output and
RS-232
Wiegand
Input
Relay
Ethernet
FIGURE 2.

5
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
STEP 3. APP INSTRUCTIONS
How to install the app:
The BDS Management software install U disk has two modes: installation mode and update mode.
Installation Mode: The filename is BDS-8 MGNT_Setup_v2.4.0.6.exe This file can be automatically installed by putting it in the root
directory of a USB flash drive.
Update Mode: The filename is BDS-8 MGNT_Setup_v2.4.0.6.exe under the “resource” folder.
You can use the U disk to automatically update the installation package.
You can also connect the mouse and U disk at the same time, select the file on the resource manager and click install.
3.1 ENTER THE SETTING INTERFACE
Connect a mouse. Press the Middle mouse button and enter the password 123456 to enter the setting interface. (The right mouse button
is is used to exit on an Android device.)
FIGURE 3.

61. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
3.2 APPLICATION SETTINGS
1. Device name setting: Set the device name.
2. Body temperature setting: Body temperature detection, body temperature alarm, mask detection function switch on and body
temperature threshold.
3. Recognition parameter setting: The lower the threshold, the higher the recognition accuracy, the more the recognition times, the slower
the stranger is reported.
4. Volume setting: Set the volume.
5. Startup settings: Auto-start after booting, and the application will automatically start after exiting.
6. Identification effect display: Setting of the LED light, green light for success (settable display image name), red light for failure, fill light.
7. Apply password setting: Set password, initial password is 123456
8. Camera preview resolution setting: Set the resolution.
9. Screen saver brightness setting: Set brightness.
10. Device restart time setting: Setting of the device restart time.
11.Relay mode.(See Step 1, Connect the gate.)
12. Application initialization: restore the initial application settings.
FIGURE 4.

7
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
3.3 FACE IMAGE ACQUISITION
FIGURE 5.
Enter face.

81. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
3.4 APPLICATION INFORMATION: VIEW THE BASIC INFORMATION OF THE DEVICE
FIGURE 6.

9
1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
3.5 PASS RECORD
Save and view the information of a pedestrian’s face and temperature, can be exported with U disk.
FIGURE 7.

10 1. 8 7 7. 8 7 7. 2 2 6 9 BLACKBOX.COM
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
INSTALLATION STEPS
3.6 FACE LIBRARY: INFORMATION OF FACE
FIGURE 8.