Blackline Safety G7 EXO Instruction sheet

headquarters [phone] | fax [phone] | toll-free 1 877 869 7212 | Address Unit 101, 1215 13 Street SE, Calgary, AB T2G 3J4, Canada | web BlacklineSafety.com
The G7 EXO Universal Mount assembly comes with the following:
•G7 EXO Universal Mount Top and Bottom (SKU# ACC-G7EXO-UMK ) -1.2 kg / 3 lbs with U-bolts
•2 U-bolts, 1 ½” ID
•2 U-bolts, 3” ID
•2 U-bolts, 5 5/8” ID
•4 mm Hex L-Key (3 3/8")
•Hardware (E-style retaining ring, m5 screws, nuts, washers, and spring-lock washers)
The following Blackline Safety items and accessories can be
mounted using the EXO Universal Mount ( ).
•G7 EXO - SKU# G7EXO-xx2 (11.8 kg / 26.0 lbs)
•Gas Tank Holder - SKU# ACC-G7EXO-UMK-GAS (0.25
kg / 0.6 lbs)
•Mast - SKU# ACC-G7EXO-UMK-MAST (0.6 kg / 1.3 lbs)
•Solar Panel Mount - SKU# ACC-G7EXO-UMK-SOLAR
MOUNT (0.8 kg / 1.8 lbs)
•Alarm Horn and Beacon - SKU# ACC-G7EXO-SIREN-M
(2.1 kg / 4.6 lbs)
•Safety Tether – SKU# ACC-G7EXO-UMK-SC
Users are responsible for mounting the EXO and accessories
in a safe manner.
Install the G7 EXO Universal Mount and Accessories

headquarters [phone] | fax [phone] | toll-free 1 877 869 7212 | Address Unit 101, 1215 13 Street SE, Calgary, AB T2G 3J4, Canada | web BlacklineSafety.com
Mount a G7 EXO on a beam or railing
Mount a gas tank holder to the G7 EXO
1. Hook the gas tank mount to the side of the EXO Universal Mount. Use either the lower or
upper hook, depending on the desired height. Secure the tank with the screw provided.
2. Attach the rubber strap to the gas tank mount on the desired side of the mount and fasten it
with the thumb screw.
3. Fit the gas tank into the holder and hook the strap at the appropriate notch. Tighten or loosen
as necessary.
1. Screw the plastic knob into the universal mount top and attach the
retaining ring.
2. Use 4 flat-head m5 screws to attach the universal mount top to the
mount bottom.
3. Find a suitable and safe beam or railing to mount the G7 EXO to. Ensure
the EXO will be accessible at a comfortable height
4. Use the appropriately sized pair of U-bolts (with nuts, washers, and lock
washers) to attach the mount bottom to the structure.
5. If necessary, use a block (not supplied) to mount the U-bolts tight to
the structure.
6. Once the mount is securely installed, lift the G7 EXO onto the mount
top and screw in the plastic knob until tight.

headquarters [phone] | fax [phone] | toll-free 1 877 869 7212 | Address Unit 101, 1215 13 Street SE, Calgary, AB T2G 3J4, Canada | web BlacklineSafety.com
Attach a mast to the G7 EXO Universal Mount
1. Hook the mast mount to the side of the EXO mount, then use the screws
that come with the mast assembly to secure it in place.
2. Fit the bottom of the mast into the mast mount, ensuring it clicks into
place.
3. Fit the top of the mast into the bottom of the mast,
again ensuring it clicks into place. The mast is now
ready to mount another accessory, such as the Mono
Solar Mount or Alarm Horn and Siren, onto it.
Mount a Mono Solar Panel to the G7 EXO Mast
1. Loosen the four screws on the solar panel bracket to open a gap between the solar panel plate
and solar panel brackets.
2. Slide the brackets behind the solar panel back frame lip, sandwiching the solar panel frame
between the brackets and the main plate. Adjust so the bracket is centered on the solar panel.
Tighten the four screws to secure the solar panel to the bracket.
3. Use two hex screws and washers on each side of the pivot point to attach the solar panel pivot
to the solar panel plate.
4. Screw the two nylon knobs, with washers, into either side of the solar panel pivot.
5. Use U-bolts to attach the solar panel pivot to the mast, then add lock washers.
Mono Solar
Module
Solar Panel
Bracket
Solar Panel
Plate
Solar Panel
Pivot

headquarters [phone] | fax [phone] | toll-free 1 877 869 7212 | Address Unit 101, 1215 13 Street SE, Calgary, AB T2G 3J4, Canada | web BlacklineSafety.com
Mount an Alarm Horn and Siren to the G7 EXO Mast
1. Attach U-bolts to the alarm horn mount using lock washers and nuts.
2. Attach the alarm horn and siren to the alarm horn mount using two hex screws.
3. Slide the alarm horn assembly onto the mast through the U-bolts, and tighten the U-bolt nuts
until secure.
Attach a Blackline Tether to the G7 EXO
For added a safety, a tether can be looped around the handle of a mounted EXO and a structural
support to secure it from dropping. The tether can also be used as a lock to ensure the EXO is not
moved or stolen.
1. Run the tether through the handle of the EXO and around a structural support. Ensure that the
tether is tight enough that the EXO will drop no further than 24 inches (61 cm) if the EXO
becomes detached from the structure it’s mounted to.
2. Use the carabiner to secure the two ends of the tether, then tighten the carabiner.
If a tethered EXO falls, the handle and cable must be inspected before reuse. Remove the rubber
bumper on the handle and inspect the entire handle for any damage. Be sure to check underneath the
handle, and the ribs inside the handle. Check the cable for any damage. If damaged, contact Blackline
Support.
Visit support.Blacklinesafety.com to download the technical user manual with descriptions of how to use and configure your device
and for detailed specifications.
EXO mast
Alarm horn
and siren
Alarm horn
mount