Blackline Safety LONER M6 User manual

The Loner M6 Safety System

CONTENTS
About the device
Starting your shift
During your shift
Generating Manual Alerts
Receiving a voice call
Ending your shift
Questions?

ABOUT THE DEVICE

ABOUT THE DEVICE
There are three primary mechanical
components of the Loner device.
Belt Clip
Latch
SureSafe monitoring
light
and power button

STARTING YOUR SHIFT

Press the power button
The green SureSafe light will
blink until it is connected to the
Blackline Safety Network.
Once connected, the light will be
SOLID GREEN.
This means your safety is
now monitored.
STARTING YOUR SHIFT
TURNING ON YOUR LONER

Clip the device to the side of your hip or to your chest pocket
STARTING YOUR SHIFT
WEARING YOUR LONER

Do not leave Loner unattended when powered on
This can lead to false alerts
STARTING YOUR SHIFT

DURING YOUR SHIFT

During your shift, the device may ask you to confirm
that you are OK when it detects one of the
following:
No-motion Fall detection Check-in
DURING YOUR SHIFT
AUTOMATIC FEATURES

No-motion
Fall
Detection
Check-in
DURING YOUR SHIFT
Pending Alarm
If you’re OK press
the confirm button
on the latch
This returns Loner to
normal function.
No notification is
sent.
AUTOMATIC FEATURES –IF YOU’RE OK

No-motion
Fall
Detection
Check-in
DURING YOUR SHIFT
Pending Alarm If you can’t press the confirm
button after a certain period of
time, the device will go into high
alarm
This sends an
alert notification
The high alarm can be silenced by
pressing and holding the button. The
alert notification still remains active.
Once an alert is acknowledged
by monitoring personnel, the
loner will display a blue light
AUTOMATIC FEATURES –IF YOU CAN’T
CONFIRM

To do this, press and hold the latch for two
vibrations. This will reset the check-in timer
before the automatic alarm sounds.
Your device will automatically check you in
if you are driving over 35 km/h.
00:54:34 2:00:00
Before pre-check in Check-in timer reset
DURING YOUR SHIFT
PRE CHECK-IN

Emergency alert
(Audible)
Silent alert
During your shift, you may need to request help
using one of the manual features:
DURING YOUR SHIFT
MANUAL FEATURES

Emergency alert
An alert
notification will
be sent to
monitoring
personnel
DURING YOUR SHIFT
The high alarm can
be silenced by
pressing and holding
the button. The alert
notification still
remains active.
Once an alert is
acknowledged by
monitoring
personnel, the loner
will display a blue
light
Request help by
pulling down the
latch

Silent Alert
Press the confirm button
until the vibration stops
(two full vibration pulses ~5 sec.)
(No audible or visual alarm is generated on the Loner device)
DURING YOUR SHIFT
An alert
notification will
be sent to
monitoring
personnel
No alert acknowledged blue light
will be displayed on the device during a silent
alert even if monitoring personnel have
acknowledged the incident

RECEIVING A VOICE CALL

A voice call can be made by monitoring personnel
directly to the device. After an alert is triggered
the device will beep once when a call is
connected.
This is the safety
monitoring center.
We had an alert
from your device.
*BEEP*
RECEIVING A VOICE CALL
That was a
false alarm. I
do not require
assistance.
Understood.
I will go
ahead and
resolve your
alert.
*BEEP*
Once the call is connected you can speak back
and forth to monitoring personnel. When the call
has ended the device will beep once more.
RECEIVING A VOICE CALL

When a silent alert is generated, monitoring personnel can still
connect with the Loner device. However the Loner will not beep and it
will be in a ‘listen only’ mode.
RECEIVING A VOICE CALL
RECEIVING A VOICE CALL –AFTER A SILENT
ALERT
…

NOTIFICATIONS