Blackline Safety G6 User manual

Getting Started Guide
G6 DOCK

G6 DOCK
G6 cradle
G6 cradle
Gas inlet
Purge
Gas type
label
Activation
code
Gas out
exhaust

GAS INLET CONFIGURATION
G6 Dock is equipped with a Gas out exhaust, a
purge inlet, and a gas inlet.
Gas Out Exhaust
Viewed from the back of G6 Dock, the Gas out
exhaust is the connector on the right. It is used
to transfer calibration gas to a safe exhaust
location.
WARNING: Never connect gas to the Gas out
exhaust.
Micro USB
power
port

Purge Inlet
Viewed from the back of G6 Dock, the Purge
inlet is on the bottom left side. It supplies
clean air, removing residual gas from G6 Dock.
Blackline recommends attaching the optional
dock lter to the Purge inlet when using G6
Dock in dusty or humid environments.
Gas Inlet
Viewed from the back of G6 Dock, the Gas inlet
is on the top left side. By default, the Gas inlet is
preprogrammed in Blackline Live for H2S. If your
G6 has a sensor other than H2S, you will need to
update your Dock’s inlet in Blackline Live.
To update your Dock’s inlet in Blackline Live:
1. From the Main menu, select Docks. The
Docks page opens.
2. Select the G6 tab.
3. Select the dock you want to update. The
Dock conguration details page opens.
4. Select EDIT.

5. Select your G6 gas sensor from the Gas
drop down.
6. Enter the calibration gas concentration in
the Concentration eld.
7. Enter the Gas cylinder information.
8. Select SAVE.
9. When the settings have saved, lock your
G6 into the dock and select Dock update
from the device’s Dock menu.
NOTE: You need to be an Account User
in Blackline Live to update G6 Dock gas
inlet settings. Contact your Blackline Live
administrator if you do not have access.
Activation Code
Use the activation code on the back of G6 Dock
to identify nd it in Blackline Live. If you cannot
see your G6 Dock in Blackline Live, contact our
Customer Care team.

POWERING ON G6 DOCK
Connect the power cable to the port on the
bottom of the dock. Feed the power cable
through the tracks along the bottom to allow
the dock to lie at on a surface.
When plugged in, the green LED light at the
front of the dock will turn on to indicate power.
Feed power cable
Green LED light

LOCKING G6 INTO G6 DOCK
To access the following G6 Dock functionality,
G6 must be locked into G6 Dock’s cradle:
Charging G6
Bump testing G6
Calibrating G6
Accessing the G6 Dock menu
To lock G6 into G6 Dock’s cradle:
1. Place G6 into the G6 Dock cradle.
2. Lock G6 into G6 Dock by positioning your
ngers over G6’s top indicator lights and
pressing G6 rmly down into the cradle
until the locking mechanism clicks into
place.
IMPORTANT: To avoid damaging G6 Dock, do
not remove your device by pulling it out of
the dock without pushing down the device to
unlock the locking mechanism.

1
2
WARNING: When locking G6 into the dock, press
down over the top indicator lights. Do not press
down on the antenna, as doing so may cause the
data and power contacts to disconnect.

CONNECTING GAS
Use the included tubing and quick connects to
connect G6 Dock to a gas cylinder.
To connect a gas cylinder to G6 Dock:
1. Attach a quick connect to the provided
tubing.
2. Ensure the other end of the tubing is
attached to a demand ow regulator on
the gas cylinder.
3. Insert the quick connect end into the
dock’s Gas inlet.
4. Twist the quick connect clockwise until it
clicks securely into place.

106268/R1/2022-12-16
LEARN MORE
North America
Toll Free: 1-877-869-7212 (24 hours)
[e-mail]
Europe/United Kindgom
[phone] (8 am-5 pm GMT)
[e-mail]
International
[phone] (24 hours)
[e-mail]
SUPPORT.BLACKLINESAFETY.COM