Blaupunkt BARCELONA MP35 User manual

Radio / CD / MP3
http://www.blaupunkt.com
Barcelona MP35 7 645 250 310
Madrid MP35 7 645 260 310
Operating Instructions

2
12
35
2
10 8
1
4
11 67
9

34
CONTROLS
1Button to switch the device on/
off and operate the volume mute
function.
2button, to open the flip-re-
lease control panel
3Volume control
4BND•TS button
Short press: Select the FM
memory banks and the MW and
LW wavebands.
Long press: Start the Travelstore
function.
5AUDIO button to adjust the
bass, treble, balance and fader.
Select an equalizer preset.
Activate, deactivate and adjust
X-BASS.
6Arrow buttons
7MENU button
Short press: Open the settings
menu.
Long press: Start the scan func-
tion.
8TRAF•RDS button
Short press: Switch traffic-infor-
mation standby on/off.
Long press: Switch the RDS
function on/off.
9Keys 1- 6
:DIS button
Short press: Briefly display the
clock time.
Long press: Configure the dis-
play.
;SRC button
Switch sources between radio,
CD/MP3, CD changer (if con-
nected) andAUX.
<button to eject a CD from the
device (only visible when the
control panel is open).

35
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
CONTENTS
Notes and accessories .......... 37
Road safety................................... 37
Installation..................................... 37
Accessories .................................. 37
Detachable control panel
(flip-release panel) ................ 38
Theft protection............................. 38
Detaching the control panel .......... 38
Attaching the control panel ........... 38
Off timer ....................................... 39
Switching on/off .................... 40
Adjusting the volume............. 41
Setting the power-on volume......... 41
Quick volume reduction (mute) ..... 41
Switching the confirmation beep
on/off ............................................ 41
Telephone audio............................ 42
Radio mode............................ 43
Adjusting the tuner settings........... 43
Switching to radio mode ............... 43
RDS functions............................... 43
Selecting the waveband /
memory bank ................................ 44
Tuning into a station ...................... 44
Setting the sensitivity of station
seek tuning ................................... 44
Storing stations............................. 45
Storing stations automatically
(Travelstore).................................. 45
Listening to stored stations ........... 45
Scanning receivable stations
(SCAN)......................................... 45
Setting the scanning time.............. 46
Programme type (PTY) ................. 46
Optimising radio reception............ 47
Configuring the display ................. 47
Traffic information ................. 48
Switching traffic information
priority on/off ................................ 48
Setting the volume for traffic
announcements............................. 48
CD mode................................ 49
Switching to CD mode.................. 49
Selecting tracks ............................ 49
Fast track selection....................... 49
Fast searching (audible)................ 49
Random track play (MIX)............... 50
Scanning tracks (SCAN) .............. 50
Repeating tracks (REPEAT) .......... 50
Pausing playback (PAUSE) ........... 50
Configuring the display ................. 50
Displaying CD text ........................ 51
Traffic announcements in
CD mode ...................................... 51
Ejecting a CD ............................... 51
MP3 mode.............................. 52
Preparing an MP3-CD .................. 52
Switching to MP3 mode................ 53
Configuring the display ................. 53
Selecting a directory ..................... 54
Selecting tracks/files..................... 54
Fast searching .............................. 54
Random track play (MIX)............... 54
Scanning tracks (SCAN) .............. 55
Repeating individual tracks or
whole directories (REPEAT).......... 55
Pausing playback (PAUSE) ........... 55

36
CONTENTS
CD-changer mode ................. 56
Switching to CD-changer mode.... 56
Selecting CDs .............................. 56
Selecting tracks ............................ 56
Fast searching (audible)................ 56
Configuring the display ................. 56
Repeating individual tracks or
whole CDs (REPEAT) ................... 56
Random track play (MIX)............... 57
Scanning all the tracks on all
the CDs (SCAN)........................... 57
Pausing playback (PAUSE) ........... 57
Remote control ...................... 58
CLOCK time ........................... 58
Displaying the clock time .............. 58
Setting the clock time ................... 58
Selecting 12/24-hour clock mode . 58
Displaying the time continuously
when the device is off and the
ignition is on.................................. 59
Briefly displaying the time when
the device is switched off.............. 59
Sound..................................... 59
Adjusting the bass ........................ 59
Adjusting the treble....................... 60
Setting the left/right volume
distribution (balance)..................... 60
Adjusting the front/rear volume
distribution (fader)......................... 60
Equalizer presets .......................... 61
X-BASS .................................. 61
Adjusting the brightness
(dimmer) ................................ 62
Entering the power-on
message ................................ 63
Configuring the level display . 63
External audio sources.......... 64
Switching the AUX input on/off ..... 64
Specifications ........................ 64

37
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Notes and accessories
Thank you for choosing a Blaupunkt
product. We hope you enjoy using this
new piece of equipment.
Please read these operating instruc-
tions before using the equipment for
the first time.
The Blaupunkt editors are constantly
working on making the operating in-
structions clearer and easier to under-
stand. However, if you still have any
questions on how to operate the device,
please contact your dealer or the tele-
phone hotline for your country. You will
find the telephone number printed at the
back of this booklet.
We provide a manufacturer guarantee
on our products bought within the Eu-
ropean Union. You can view the guar-
antee conditions at www.blaupunkt.de
or ask for them directly at:
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
D-31139 Hildesheim
Gerrmany
NOTES AND ACCESSORIES
Road safety
Road safety has absolute prior-
ity. Only operate your car sound sys-
tem if the road and traffic conditions
allow you to do so. Familiarise your-
self with the device before setting off
on your journey.
You must always be able to hear
police, fire service and ambulance
sirens in good time from inside your
vehicle. For this reason, listen to your
car sound system at a moderate vol-
ume level during your journey.
Installation
If you want to install your car sound sys-
tem yourself, please read the installa-
tion and connection instructions that
follow these operating instructions.
Accessories
Only use accessories approved by Blau-
punkt.
Remote cµontrol
The RC 08, RC 10, RC 10 H or RC 12H
(available as optional accessories) re-
mote control allows you to access the
most important functions of your car
sound system safely and conveniently
from your steering wheel.
You cannot switch the device on/off us-
ing the remote control.
Amplifiers
You can use all Blaupunkt and Velocity
amplifiers.
CD changers
You can connect the following Blaupunkt
CD changers: CDC A 08, IDC A 09 and
CDC A 03.
02Barcel_MadridMP35 gb®22.06.2005, 14:14 Uhr37

38
Detachable control panel
(flip-release panel)
Theft protection
Thedeviceis equipped with a detacha-
ble control panel (flip-release panel) as
a way of protecting your equipment
against theft. The device is worthless
to a thief without this control panel.
Protectyourdeviceagainsttheftbytak-
ing the control panel with you whenev-
er you leave your vehicle. Do not leave
the control panel inside your vehicle -
not even in a hiding place.
The control panel has been designed
to be easy to use.
Notes:
●Never drop the control panel.
●Never expose the control panel to
direct sunlight or other heat sourc-
es.
●Avoid direct skin contact with the
control panel’s electrical contacts. If
necessary, clean the contacts with
a lint-free cloth and some alcohol.
Detaching the control panel
➮Press the button 2.
The control panel opens out towards
you.
➮Hold the control panel by its right
side and then pull the control panel
straight out of the bracket.
Notes:
●The device will switch off after a
particular time period configured by
you. For further details, read the
section entitled “OFF TIMER”in
this chapter.
●All the current settings are saved.
●Any CD already inserted in the de-
vice remains there.
Attaching the control panel
➮Hold the control panel at approxi-
mately right angles to the device.
➮Slide the control panel into the de-
vice’s guides that are positioned on
the left and right at the lower edge
of the housing. Push the control
panel carefully into the bracket until
it clicks into place.
➮Flip up the control panel and care-
fully press it into the device until it
clicks into place.
1. 2.
DETACHABLE CONTROL PANEL

39
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Note:
●When attaching the control panel,
make sure you do not press the
display.
If the device was still switched on when
you removed the control panel, it will
automatically switch on with the last
settings activated (i.e. radio, CD/MP3,
CD changer orAUX) when the panel is
replaced.
Off timer
Note:
●The device is equipped with a time-
out function. If, for instance, you
press the MENU button 7and se-
lect a menu item, the device will
switch back approx. 8 seconds af-
ter the last button was pressed.
Any changes to the settings that
you have made will be saved.
After you detach the control panel, the
device will switch off after a preset time
period.Youcansetthistimetobetween
0 and 30 seconds.
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “OFF TIMER”appears in
the display.
➮Adjust the time using the but-
tons 6.
When you have finished making your
changes,
➮press the MENU button 7twice.
Note:
●If you set the off-timer to 0 sec-
onds, the device will switch off im-
mediately as soon as you open the
control panel.
DETACHABLE CONTROL PANEL

40
Note:
●To protect the vehicle battery, the
device will switch off automatically
after one hour if the ignition is off.
Switching on by inserting a CD
If the device is switched off and there is
no CD present in the drive,
➮press the button 2.
The control panel opens.
➮Gently insert the CD with its printed
side uppermost into the drive until
you feel some resistance.
The drive draws in the CD automatical-
ly.
You must not hinder or assist the drive
as it draws in the CD.
➮Gently close the control panel
whilst exerting a little pressure until
you feel it click into place.
Thedeviceswitchesonandstartsplay-
ing the CD.
Note:
●If the vehicle ignition was switched
off before you inserted the CD, you
will first have to switch on the de-
vice by pressing button 1in order
to start playing the CD.
Switching on/off
Therearevariouswaysofswitchingthe
device on/off:
Switching the device on/off using
the vehicle ignition
If the device is correctly connected to
the vehicle’s ignition and you did not
switch it off by pressing button 1, the
devicewillswitchon/off simultaneously
with the ignition.
Switching the device on/off using
the detachable control panel
➮Detach the control panel.
The device switches off.
Note:
●The device will switch off after a
preset time period. For further de-
tails, read the section entitled “Off
timer”.
➮Attach the control panel again.
The device switches on. The last set-
ting (radio, CD/MP3, CD changer or
AUX) will be reactivated.
Switching on/off using button 1
➮To switch on the device, press but-
ton 1.
➮To switch off the device, press and
hold down button 1for longer
than two seconds.
The device switches off.
SWITCHING ON/OFF

41
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Adjusting the volume
Youcanadjustthevolumeinstepsfrom
0 (off) to 66 (maximum).
To increase the volume,
➮turn the volume control 3clock-
wise.
To decrease the volume,
➮turn the volume control 3anti-
clockwise.
Setting the power-on volume
You can set the power-on volume.
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “ON VOLUME”appears
in the display.
➮Adjust the power-on volume using
the buttons 6.
To helpyouadjustthesettingmoreeas-
ily, the device will increase or decrease
thevolumeas youmakeyourchanges.
Ifyouchangethesettingto“LASTVOL”,
the volume level that was set the last
time you switched off the device will be
activated again.
Note:
●To protect your hearing, the power-
on volume is limited to a value of
“38”. If the volume level was higher
than this when the device was last
switched off and the “LAST VOL”
setting is activated, the system will
reset the volume to “38”when you
switch the device on again.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Quick volume reduction (mute)
You can quickly decrease the volume
(mute) to a level preset by you.
➮Briefly press button 1.
“MUTE”appears in the display.
Cancelling mute
To return to your previously set volume
level,
➮briefly press button 1again.
Setting the mute level
You can adjust the mute level.
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “MUTE LVL”appears in
the display.
➮Adjust the mute level using the
buttons 6.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Switching the confirmation beep
on/off
Thesystemwillplayaconfirmationbeep
for some functions if you keep a button
pressed down for longer than two sec-
onds, for instance, when you assign a
radiostationtoastationbutton.Youcan
switch the beep on/off.
ADJUSTING THE VOLUME

42
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “BEEP ON”or “BEEP
OFF”appears in the display.
➮Adjust the beep setting using the
buttons 6. “OFF”means the
beep is switched off and “ON”
means the beep is switched on.
When you have finished adjusting the
setting,
➮press the MENU button 7.
Telephone audio
If your car sound system is connected
to a mobile telephone, the sound sys-
tem’s volume will be muted as soon as
you “pick up”the telephone. The tele-
phonecallisthenoutputtedoverthecar
sound system’s loudspeakers. This re-
quiresthatthemobiletelephonebecon-
nected to the car sound system as de-
scribed in the installation instructions.
You will need a cable for this with the
followingBlaupunktnumber:7 607 001
503.
If the sound system receives a traffic
announcementduringa telephone call,
the system will only play the traffic an-
nouncementafteryouhavefinishedthe
call.
You can set the volume at which you
wanttelephonecallstobeinitiallyheard.
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “TEL VOL”appears in the
display.
ADJUSTING THE VOLUME
➮Set your preferred volume level us-
ing the buttons 6.
When you have finished making your
changes,
➮press the MENU button 7twice.
Note:
●You can use the volume control 3
to adjust the volume of a telephone
call whilst the call is being output-
ted by the sound system.

43
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Radio mode
This device is equipped with an RDS
radio receiver. Many of the receivable
FM stations broadcast a signal that not
only carries the programme but also
additional information such as the sta-
tion name and programme type (PTY).
The station name appears in the dis-
play as soon as the tuner receives it.
Adjusting the tuner settings
To ensure that the tuner works proper-
ly,thedevicemustbeconfiguredforthe
regioninwhichyouareusingit.Youcan
choose between Europe (EUROPE),
UnitedStates(USA),SouthAmerica(S-
AMERICA) and Thailand (THAI). By
default, the tuner is set to the region in
which the device was sold. If you en-
counter problems with radio reception,
please check this setting.
The radio functions described in these
operating instructions refer to the EU-
ROPE tuner setting.
➮Press and hold down the 1and 5
buttons 9simultaneously and
switch on the device again by
pressing button 1.
“TUNER”is displayed.
➮Select your tuner region using the
or button 6.
To save the setting,
➮switch the device off and on again
or wait approx. 8 seconds. The car
sound system starts with the last
setting activated (radio, CD/MP3,
CD changer orAUX).
Switching to radio mode
If you are in CD/MP3, CD-changer or
AUX mode,
➮press the BND•TS button 4
or
➮press the SRC button ;repeated-
ly until the memory bank (e.g.
“FM1”) appears in the display.
RDS functions
The convenient RDS functions AF (Al-
ternative Frequency) and REGIONAL
extend your radio’s range of functions.
●AF: If the RDS function is activat-
ed, the radio automatically tunes
into the best receivable frequency
for the station that is currently set.
●REGIONAL:At certain times, some
radio stations divide their pro-
gramme into regional programmes
providing different content. You can
use the REG function to prevent
the car radio from switching to al-
ternative frequencies that are
broadcasting different programme
content.
Note:
●REGIONAL must be activated/de-
activated separately in the menu.
Switching the RDS function on/off
If you want to use the RDS functions
(AF and REGIONAL),
➮press and hold down the
TRAF•RDS button 8for longer
than two seconds.
The RDS function is active when the
RDS symbol is shown in the display.
RADIO MODE

44
Switching REGIONAL on/off
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “REG”appears in the dis-
play. “OFF”or “ON”is displayed
alongside “REG”.
➮To switch REGIONAL on/off, press
the or button 6.
➮Press the MENU button 7.
Selecting the waveband /
memory bank
You can use this device to receive pro-
grammes broadcast over the FM fre-
quency range as well as the MW and
LW (AM) wavebands. There are three
memory banks available for the FM
waveband (FM1, FM2 and FMT) and
one for each of the MW and LW wave-
bands. Six stations can be stored in
each memory bank.
To switch between the FM memory
banks (FM1, FM2 and FMT) and the
MW and LW wavebands,
➮briefly press the BND•TS button
4.
Tuning into a station
There are various ways of tuning into a
station.
Automatic station seek tuning
➮Press the or button 6.
The radio tunes into the next receiva-
ble station.
Tuning into stations manually
Youcan alsotune intostationsmanual-
ly.
Note:
●You can only tune into stations
manually if the RDS function is de-
activated.
➮Press the or button 6.
Browsing through broadcasting
networks (only FM)
If radio stations provide several pro-
grammes,youhavetheoptionofbrows-
ing through their “broadcasting net-
works”.
Note:
●The RDS function must be activat-
ed before you can use this feature.
➮Press the or button 6to
switch to the next station on the
broadcasting network.
Note:
●When using this feature, you will
only be able to switch to stations
that you have received once before
already. To receive the stations,
use the scan function or the Travel-
store function.
Setting the sensitivity of station
seek tuning
You can choose whether the radio
should only tune into stations providing
good reception or whether it can also
tune into those with a weak reception.
➮Press the MENU button 7.
RADIO MODE

45
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
➮Press the or button 6repeat-
edly until “SENS”and the currently
set value appear in the display.
“SENS HI6”means that the tuner is set
tothehighestsensitivitysetting.“SENS
LO1”means it is set to the lowest sen-
sitivity setting.
➮Set the desired sensitivity using the
buttons 6.
When you have finished adjusting the
setting,
➮press the MENU button 7.
Note:
●You can set different sensitivity
levels for FM and MW or LW.
Storing stations
Storing stations manually
➮Select the memory bank that you
want (FM1, FM2, FMT) or one of
the wavebands (MW or LW).
➮Tune into the station that you want.
➮Press and hold down one of the
station buttons 1 - 6 9for longer
than two seconds to assign the sta-
tion to that button.
Storing stations automatically
(Travelstore)
You can automatically store the six sta-
tionsprovidingthe best reception in the
region(onlyFM).Thestationsarestored
in the FMT memory bank.
Note:
●Any stations previously stored in
this memory bank are deleted in
the process.
➮Press and hold down the BND•TS
button 4for longer than two sec-
onds.
The storing procedure begins. “FM
TSTORE”appears in the display. After
the process has completed, the radio
will play the station that is stored in
memory location 1 of the FMT memory
bank.
Listening to stored stations
➮Select the memory bank or wave-
band.
➮Press the station button 1 - 6 9
that corresponds to the station that
you want to listen to.
Scanning receivable stations
(SCAN)
You can use the scan function to listen
toall the receivable stations briefly.You
can set the scanning time in the menu
to between 5 and 30 seconds (in steps
of 5 seconds).
Starting SCAN
➮Press and hold down the MENU
button 7for longer than two sec-
onds.
Scanning begins. “SCAN”appears
brieflyinthedisplayfollowedbyaflash-
ing display of the current station name
or frequency.
Cancelling SCAN and continuing
listening to a station
➮Press the MENU button 7.
Scanningstopsandtheradiocontinues
playingthestationthatittunedintolast.
RADIO MODE

46
Setting the scanning time
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “SCAN TIME”appears in
the display.
➮Set the desired scanning time us-
ing the buttons 6.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Note:
●The scanning time that you set is
also used when scanning in CD/
MP3 mode and in CD-changer
mode.
Programme type (PTY)
Besides transmitting the station name,
someFMstationsalsoprovideinforma-
tion on the type of programme they are
broadcasting.Yourcarradiocanreceive
and display this information.
Forexample,theprogrammetypescan
be:
CULTURE TRAVEL JAZZ
SPORT NEWS POP
ROCK CLASSICS
You can use the PTY function to select
stationsofaparticularprogrammetype.
PTY-EON
If you specify the programme type and
start seek tuning, the radio will switch
from the current station to a station of
the selected programme type.
Notes:
●If the tuner does not find a station
that matches the selected pro-
gramme type, you will hear a beep
and “NO PTY”appears briefly in
the display. The radio will then re-
tune to the station that it received
last.
●If the tuned radio station or another
station on the broadcasting net-
work broadcasts your selected pro-
gramme type at a later point in
time, the radio will automatically
switch from the currently tuned sta-
tion or from CD/MP3 mode or CD-
changer mode to the station whose
programme type matches the one
you selected.
Switching PTY on/off
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “PTY ON”or “PTY OFF”
appears in the display.
➮Press the or button 6to
switch PTY ON or OFF.
➮Press the MENU button 7.
Selecting the PTY language
You can select the language in which
the programme types are displayed.
The following are available:
“DEUTSCH”, “ENGLISH”and
“FRANÇAIS”.
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “PTY LANG”appears in
the display.
RADIO MODE

47
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
➮Set your preferred language using
the buttons 6.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Selecting a programme type and
starting seek tuning
➮Press the or button 6.
The current programme type appears
in the display.
➮If you want to select another pro-
gramme type, you can do so by
pressing the or button 6
whilst this display is visible.
The selected programme type appears
briefly in the display.
➮Press the or button 6to start
seek tuning.
The radio will then tune into the next
stationitfindsthatmatchesyourselect-
ed programme type.
Optimising radio reception
HICUT
TheHICUTfunctionimprovesreception
during poor radio reception (only FM).
If interference occurs, the interference
level is cut automatically.
Switching HICUT on/off
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “HICUT”appears in the
display.
➮Press the or button 6to ad-
just the HICUT setting.
“HICUT 0”means that the interference
level will not be cut automatically. “HI-
CUT 1”means that it will be cut auto-
matically.
➮Press the MENU button 7.
Configuring the display
In radio mode, you have the option of
displaying the waveband together with
the memory bank and the time or the
station name / frequency of the current
station.
➮To switch between the displays,
press and hold down the DIS
button :for longer than two sec-
onds.
RADIO MODE

48
Traffic information
Your device is equipped with an RDS-
EON receiver. EON stands for En-
hanced Other Network.
Whenever a traffic announcement (TA)
is broadcast, the system switches au-
tomatically from a station that does not
provide traffic reports to the appropri-
ate traffic information station within the
broadcasting network that does.
Oncethetrafficreporthasbeenplayed,
the system will switch back to the pro-
gramme you were listening to before.
Switching traffic information
priority on/off
➮Briefly press the TRAF•RDS but-
ton 8.
Traffic announcement priority is active
when the traffic-jam symbol lights up in
the display.
Notes:
You will hear a warning beep:
●if you leave the reception area of a
traffic information station that you
are currently listening to.
●if you are receiving a traffic infor-
mation station and the volume is
set to minimum (0) or if, whilst lis-
tening to a CD/MP3, a CD in the
changer or an AUX source, you
leave the reception area of the
tuned traffic information station and
the subsequent automatic search
cannot find a new traffic informa-
tion station.
●if you retune the radio from a traffic
information station to a station that
does not broadcast traffic informa-
tion.
If you hear the warning beep, you can
either switch off traffic information pri-
ority or tune into a station that broad-
casts traffic information.
Setting the volume for traffic
announcements
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “TA VOLUME”appears in
the display.
➮Adjust the volume using the
buttons 6.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Notes:
●You can use the volume control 3
to adjust the volume during a traffic
announcement for the duration of
that announcement.
●You can set the volume distribution
for the traffic announcements. For
further details, please read the
“Sound”chapter.
TRAFFIC INFORMATION

49
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
➮Gently close the control panel
whilst exerting a little pressure until
you feel it click into place.
The CD starts playing.
Note:
●If the vehicle ignition was switched
off before you inserted the CD, you
will first have to switch on the de-
vice by pressing button 1in order
to start playing the CD.
If there is already a CD inserted in the
drive,
➮press the SRC button 1repeated-
ly until “CD”appears in the display.
Playbackbeginsfromthepointatwhich
it was last interrupted.
Selecting tracks
➮Press one of the arrow buttons 6
to select the next or previous track.
If you press the or button 6once,
the current track will be played again
from the beginning.
Fast track selection
For fast track selection (backwards or
forwards),
➮press and hold down one of the
buttons 6until fast-reverse /
fast-forward track selection begins.
Fast searching (audible)
For fast searching (backwards or for-
wards),
➮press and hold down one of the
buttons 6until fast searching
backwards / forwards begins.
CD mode
You can use this device to play stand-
ard audio CDs, CD-Rs and CD-RWs
with a diameter of 12 or 8 cm.
Risk of severe damage to the
CD drive!
ContouredCDs(shapeCDs)arenot
suitable for playback in this unit. We
do not accept responsibility for any
damage to the CD drive that may
occur as a result of the use of un-
suitable CDs.
To ensurethesystemfunctionsproper-
ly, only use CDs labelled with the com-
pact disc logo. Problems might be ex-
perienced when playing copy-protect-
ed CDs. Blaupunkt cannot guarantee
the proper functioning of copy-protect-
ed CDs!
Besides being able to play audio CDs
on this device, you can also play CDs
containing MP3 music files. For further
details, please read the “MP3 mode”
chapter.
Switching to CD mode
If there is no CD inserted in the drive,
➮press the button 2.
The control panel opens.
➮Gently push the CD with the print-
ed side uppermost into the CD
compartment until you feel some
resistance.
The drive draws in the CD automatic-
ally.
You must not assist or hinder the drive
as it draws in the CD.
CD MODE

50
Repeating tracks (REPEAT)
If you want to repeat a track,
➮press the 4RPT button 9.
“RPT TRCK”appears briefly in the dis-
playandthe RPTsymbol lights up.The
track is repeated continuously until you
deactivate RPT.
Cancelling REPEAT
If you want to cancel the repeat func-
tion,
➮press the 4RPT button 9again.
“RPT OFF”appears briefly in the dis-
play and the RPT symbol disappears.
Normal playback is then resumed.
Pausing playback (PAUSE)
➮Press button 39.
“PAUSE”appears in the display.
Cancelling pause
➮Press button 39whilst pause
is activated.
Playback is resumed.
Configuring the display
You can choose between two display
types for CD mode:
●Track number and clock time
●Track number and playing time
➮To switch between the displays,
press and hold down the DIS
button :for longer than two sec-
onds.
Random track play (MIX)
➮Press the 5MIX button 9.
“MIX CD”appears briefly in the display
and the MIX symbol lights up. The next
randomly selected track will then be
played.
Cancelling MIX
➮Press the 5MIX button 9again.
“MIX OFF”appears briefly in the dis-
play and the MIX symbol disappears.
Scanning tracks (SCAN)
Youcanscan(brieflyplay)allthetracks
on the CD.
➮Press and hold down the MENU
button 7for longer than two sec-
onds.
The next track will then be scanned.
Note:
●You can set the scanning time. For
further details, please read the sec-
tion entitled “Setting the scanning
time”in the “Radio mode”chapter.
Cancelling SCAN and continuing
listening to a track
➮To cancel scanning, press the
MENU button 7.
The currently scanned track will then
continue to be played normally.
CD MODE

51
DANSK
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Displaying CD text
SomeCDsincludeCDtext.TheCDtext
might contain the names of the artist,
album and track.
You can allow the CD text to be dis-
played as scrolling text every time you
switchto anothertrack.Thedefault dis-
play will appear again after the whole
CD text has been shown once. For fur-
ther details, please read the section
entitled “Configuring the display”.
Switching CD text on/off
➮Press the MENU button 7.
➮Press the or button 6repeat-
edly until “CD TEXT”appears in
the display.
➮Switch the CD text function on
(“TEXT ON”) or off (“TEXT OFF”)
using the or button 6.
When you have finished adjusting the
setting,
➮press the MENU button 7twice.
Traffic announcements in CD
mode
If you wish to receive traffic announce-
ments whilst CD mode is activated,
➮press the TRAF•RDS button 8.
Traffic announcement priority is active
when the traffic jam symbol is shown in
the display. For further details, please
read the “Traffic information reception”
chapter.
CD MODE
Ejecting a CD
➮Press the button 2.
The control panel opens.
➮Press the button <next to the
CD compartment.
The CD is ejected.
➮Remove the CD.
➮Gently close the control panel
whilst exerting a little pressure until
you feel it click into place.
Notes:
●If a CD is ejected, the drive will au-
tomatically draw it back in again af-
ter approx. 10 seconds.
●You can also eject CDs whilst the
device is switched off or whilst an-
other audio source is activated.