Blaupunkt GTr 130 A User manual

ACTIVE SUBWOOFER
GTr 130 A
Enjoy it.
Operating and installation instructions
GTr 130 A Manual.indd 1 25/1/2019 2:37:09 PM

GTr 130 A Manual.indd 2 25/1/2019 2:37:09 PM

Proper system planning is vital in order to maximize
the device’s performance and road safety. Plan
your installation carefully to avoid compromising
performance reliability of the system. Consult an
authorized Blaupunkt dealer for installation or rep-
aration. Read the manual carefully before operating
the device for the rst time.
Safety Notes
Ensure to follow below safety notes during installa-
tion and wiring connection : -
•
•
•
Installation and Connection Instructions
•
•
•
Intergrated Fuse
•
Switching On/O
•
Disclaimer
•
•
Disconnect the negative terminal of the battery.
Refer to the safety notes of vehicle manufac-
turer.
Ensure positions of the holes are nowhere near
the vehicle component to avoid any damage
during drilling.
Incorrect installation may result in malfunc-
tion of the device or the car sound system.
Select a dry and well-ventilated location to
install the device.
The device must not be installed on the rear
shelf, rear seats or exposed locations.
The installation location must be suitable for
screw holes and have stable ground support.
The integrated fuse in the device protects
the output voltage and the entire electrical
system in case of malfunction. Do not replace
damaged fuse with higher current.
This device will automatically turn on if audio
signal is detected. The device will also auto-
matically turn o if audio signal is received.
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages, to property or life,
improper storage, whatsoever arising out of
or connected with the use or misuse of our
products.
USA & CANADA : Product not intended for
sale in the United States and Canada. If
purchased in the U.S. or Canada, this product
is purchased as-is. No warranty, express or
implied is provided in the U.S. and Canada.
Remote Control
1
2
3
4
5
6
Recycle and Disposal
Set the GAIN to 200mV (Min), PHASE to NORM.,
LOW PASS FILTER to Center before turning on
the device.
Set the Bass/Treble of head unit to zero. Set
volume to lower level.
Gradually increase GAIN until the desired sound
eect is achieved or until the sound distribution
in the vehicle is even.
Avoid setting volume of the head unit and GAIN
too high to prevent sound distortion. Ensure
speakers are functioning well to avoid sound
distortion too. Then adjust the LOW PASS FILTER
(L.P.F.) to the desired frequency.
Changing the LPF will change the sound output
of the subwoofer. Continue to adjust GAIN, LPF
and volume until the desiredsetting is found.
Play the music from the head unit while sitting
at the driver and switch between NORM and REV
to select the desired sound output setting. The
ideal PHASE is subjective and varies from one
vehicle to another, depending on the location of
the device and the acoustic characteristics of the
vehicle interior.
Please dispose responsibly.
INTRODUCTION
GTr 130 A Manual.indd 3 25/1/2019 2:37:09 PM

Amplier
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Amplier Technology : Class AB
Normal Output Power (RMS) : 130W
Max Output Power : 300W
Sensitivity (In Car/1W) : 92dB
Signal/Noise Ratio : 91dB
Output Impedance : 2.2 + 2.2 ohms
Frequency Response : 40Hz-150Hz
Low Pass Filter (LPF) : 50Hz-100Hz
Voltage : 14.4V (10V-16V)
Phase Switch : 0° /180°
Automatic On/O : High Level Only
Fuse Rating : 10A
Gain : 200mV – 6V
Audio in Sensitivity : Speaker Input (0.8V) / RCA
Input (82mV)
Subwoofer
•
•
•
•
Accessories
•
•
•
•
•
•
•
Speaker Size : 214.5mm x 135mm
Cone Composition : Aluminium
Magnet Type : Ferrite
Enclosure Housing Material : Aluminium
Remote Controller : Wired
DC Cord : 5.0m
Screws (Parker-Type) : M4 x 20mm
Screws (M-Type) : 6 x 8mm
2 x Bracket A : 72 x 40mm
Overall Net Weight : 3.7kg
Enclosure Dimension (L x W x H) :
280 x 200 x 74mm
INSTALLATION
SPECIFICATION
GTr 130 A Manual.indd 4 25/1/2019 2:37:09 PM

Speaker Size : 214.5mm x 135mm
Cone Composition : Aluminium
Magnet Type : Ferrite
Enclosure Housing Material : Aluminium
Remote Controller : Wired
DC Cord : 5.0m
Screws (Parker-Type) : M4 x 20mm
Screws (M-Type) : 6 x 8mm
2 x Bracket A : 72 x 40mm
Overall Net Weight : 3.7kg
Enclosure Dimension (L x W x H) :
280 x 200 x 74mm
Select either Diagram 1 or Diagram 2 for installation. Avoid audio interference by using one audio inputs
only.
WIRING DIAGRAM
Diagram 1
(High Level Input)
REMOTE CONTROL
YELLOW WIRE
BLUE/WHITE WIRE NOT IN USE IN THIS TYPE OF INSTALLATION
NOT IN USE IN THIS
TYPE OF INSTALLATION
GREY/BLACK (-) & GREY WIRE (+)
SPEAKER RIGHT CHANNEL
OUTPUT WIRE
SPEAKER LEFT CHANNEL OUTPUT WIRE
WHITE/BLACK (-) &
WHITE WIRE (+)
FUSE
10A BATTERY
12V
CONNECT BLACK WIRE (-) TO THE CHASSIS OF THE VEHICLE
CHASSIS GROUND
Diagram 2
(Low Level Input)
REMOTE CONTROL
YELLOW WIRE
BLUE/WHITE WIRE
RCA SIGNAL WIRE
AUDIO DEVICE CONTROL WIRE
CONNECT BLACK WIRE (-) TO THE CHASSIS OF THE VEHICLE
FUSE
10A BATTERY
12V
CHASSIS GROUND
GTr 130 A Manual.indd 5 25/1/2019 2:37:11 PM

Examine if your wiring is similar to Diagram 1 or Diagram 2 in case of device operation or performance
failure. The following table indicate other possible problems and solutions. Refer to an authorized Blaupunkt
dealer if problem persist.
Problem
Amplier power
up failure
No sound output
Low sound output
Buzzing noise
Squealing noise
interference
Distorted sound
output
Amplier
temperature
increased
Engine noise
(static sound)
interference
Engine noise
(alternator whine)
interference
Solution
Examine if the ground connection is intact.
Examine if remote input has at least 5V DC.
Examine if battery power is connected correctly to the + terminal.
Ensure supplied voltage is minimum 12V.
Examine if fuse is broken and replace if necessary.
Restart the device if protection LED light is on.
Examine fuses and replace if necessary.
Examine ground connection is intact.
Examine if remote input has at least 5V DC.
Examine if RCA audio cables are connected to the right inputs.
Examine if speaker wiring is intact.
Reset Level Control
Examine the Crossover Control setting.
Observe if the device is still producing noise after turning on and o the
amplier. If yes, examine if the cables are correctly connected and if the
cables and radio are in good condition. Repair or replace if the cables or the
radio are not in good condition.
Ensure RCA connections are properly connected.
Ensure input level of the device matches the signal level of the head unit.
Always set the input level to the lowest.
Examine if crossover frequency is set correctly.
Examine if speaker wire had short-circuit.
Examine the minimum speaker impedance for the amp models is correct.
Ensure good air ventilation around the device. Add external cooling fan if
necessary.
Usually caused by poor RCA cable quality, which release noise. Use only the
best quality cables, and route them away from power cables.
Examine if RCA cable are nowhere near or attached to the vehicle chassis.
Examine if head unit is properly connected to the wires.
INTRODUCTION
GTr 130 A Manual.indd 6 25/1/2019 2:37:11 PM

Examine if your wiring is similar to Diagram 1 or Diagram 2 in case of device operation or performance
failure. The following table indicate other possible problems and solutions. Refer to an authorized Blaupunkt
dealer if problem persist.
GTr 130 A Manual.indd 7 25/1/2019 2:37:11 PM

Designed and engineered by Blaupunkt Competence Center 1 113 19 009 02 01
GTr 130 A Manual.indd 8 25/1/2019 2:37:11 PM