Blaze King S.Z2091 User manual

180-Z2091_Z2093 v1.03 October 17, 2018
S.Z2091 Medium Shroud AF25 29 1/4”
S.Z2093 Large Shroud AF25 32 1/4”
NOTE: CAST PARTS SUPPLIED WITH AF25 STOVE
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com
Manufactured By
Valley Comfort Systems Inc., 1290 Commercial Way, Penticton, BC, V2A 3H5, Canada
Phone: [phone] - Fax: [phone] - www.blazeking.com - [email protected]
OPERATION & INSTALLATION MANUAL
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to chemicals including
benzene, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information:
www.P65Warnings.ca.gov

180-Z2091_Z2093 v1.03 October 17, 2018
S.Z2091 Medium Shroud AF25 29 1/4” or S.Z2093 Large Shroud AF25 32 1/4”
ITEM
NO.
PART
NUMBER DESCRIPTION QTY.
1 110.2016 AF25 CAST SHROUD TRIM TOP 1
2 110.2017 AF25 CAST SHROUD TRIM RIGHT 1
3 110.2018 AF25 CAST SHROUD TRIM LEFT 1
4 110.2021 AF25 CAST TRIM ELBOW RIGHT 1
5 110.2022 AF25 CAST TRIM ELBOW LEFT 1
6 300.0295.A SCREW TAPPING 10 X 1/2 BLK ZINC 7
7 330.0073 SCREW MACHINE 10-24 X 1/2 4
8 330.0075 SCREW MACHINE 10-24 X 1/4 14
9 375.0009 FLAT WASHER ZP #10 17
10 2099 BYPASS HANDLE HANGER 1
10
5
4
2
3
6
9
7
8
2092(MEDIUM) or
2094(LARGE) SHROUD SIDE
(supplied with kit)
1
APPLIANCE
SUPPLIED WITH
2093 (LARGE) SHROUD TOP
(supplied with kit)
2091 (MEDIUM) or
SUPPLIED WITH
MANUAL KIT
7

180-Z2091_Z2093 v1.03 October 17, 2018
S.Z2091 Medium Shroud AF25 29 1/4” or S.Z2093 Large Shroud AF25 32 1/4”
1. Fasten shroud top panel to
stove using three 10x1/2”
black screws. (FIG.1)
2. Fasten shroud sides to
stove using two 10x1/2”
black screws per side.
(FIG.2)
FIG.1
FIG.2

180-Z2091_Z2093 v1.03 October 17, 2018
S.Z2091 Medium Shroud AF25 29 1/4” or S.Z2093 Large Shroud AF25 32 1/4”
3. Partially thread thirteen
10-24x1/4” machine screws
with washers into the top,
left, and right cast trim
pieces. Leave at least a
1/16” gap between the
washers and the cast face.
(FIG.3) NOTE: Leave one
hole open on either the left
or right side for the bypass
handle hanger bracket.
4. Slide the cast trim pieces
into their respective
positions by aligning
the partially fastened
screws with the u-shaped
cut-outs on the shroud
panels. Completely tighten
machine screws once the
trim is in place.
5. Align the left and right cast
corners into their respective
positions and fasten to the
upper shroud panel using
four 10-24x1/2” machine
screws with washers.
(FIG.4)
6. Attach the bypass handle
hanger to the open hole
left from step 3, use the
remaining 10-24x1/4”
machine screw to fasten in
place. (FIG.4)
FIG.3
FIG.4
OPEN HOLE FOR BYPASS
HANDLE BRACKET

180-Z2091_Z2093 v1.03 October 17, 2018
S.Z2091 Medium Shroud AF25 29 1/4” or S.Z2093 Large Shroud AF25 32 1/4”