Blaze King PE1006 User manual

OM-PE E V1.06 January 20, 2015
PRINCESS PE1006
SOLID FUEL CATALYTIC STOVE: PE1006, PEJ1006
OPERATION & INSTALLATION MANUAL
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please SAVE THESE INSTRUCTIONS for future reference.
e authority having jurisdiction (such a municipal building department, re department, etc.) should be
consulted before installation to determine the need to obtain a permit.
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com
Manufactured By
Valley Comfort Systems Inc., 1290 Commercial Way, Penticton, BC, V2A 3H5, Canada
Phone: [phone] Fax: [phone] www.blazeking.com inf[email protected]

OM-PE E V1.06 January 20, 2015
Page 2 PE1006
Table of Contents
SPECIFICATIONS _____________________________________________________________ 3
PRODUCT INFORMATION _____________________________________________________ 4
APPLIANCE DIMENSIONS—Princess Classic PE1006BK .............................................................. 4
APPLIANCE DIMENSIONS—Princess Parlor PE1006LBK ............................................................. 5
APPLIANCE DIMENSIONS—Princess Ultra PE1006UBK.............................................................. 6
CERTIFICATION LABEL________________________________________________________ 7
SAFETY PRECAUTIONS ________________________________________________________ 8
INSTALLATION INSTRUCTIONS_________________________________________________ 11
GENERAL ........................................................................................................................................ 11
FREIGHT DAMAGE........................................................................................................................ 11
PARTS INCLUDED WITH THE PRINCESS ................................................................................... 11
OPTIONAL EQUIPMENT............................................................................................................... 11
FLOOR PROTECTION .................................................................................................................... 11
MINIMUM CLEARANCES for PE1006 and PEJ1006...................................................................... 12
COMBUSTION AIR......................................................................................................................... 13
DRAFT............................................................................................................................................. 13
VENTING SYSTEMS ...................................................................................................................... 13
MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS) ........................................... 16
OPTIONAL ACCESSORIES............................................................................................................. 17
OPERATING INSTRUCTIONS ___________________________________________________ 20
THERMOSTAT ................................................................................................................................ 20
LIGHTING THE FIRE ..................................................................................................................... 21
OPTIMAL THERMOSTAT SETTING ............................................................................................. 23
CREOSOTE __________________________________________________________________ 24
MAINTENANCE ______________________________________________________________ 25
ASH REMOVAL ...............................................................................................................................25
CATALYTIC COMBUSTOR, TESTING........................................................................................... 25
CATALYTIC COMBUSTOR, CLEANING ....................................................................................... 26
CATALYTIC COMBUSTOR, REPLACEMENT ............................................................................... 26
DOOR GLASS, CLEANING............................................................................................................. 26
DOOR GASKET INSPECTION........................................................................................................ 26
DOOR GLASS, REPLACEMENT..................................................................................................... 27
LOADING DOOR GASKET REPLACEMENT................................................................................. 27
LOADING DOOR TENSION ADJUSTMENT ................................................................................. 28
CHIMNEY DRAFTS ........................................................................................................................ 28
OPTIONAL FAN ASSEMBLY .......................................................................................................... 29
PAINT .............................................................................................................................................. 29
THERMOMETER ............................................................................................................................ 29
THERMOSTAT ................................................................................................................................ 29
TROUBLESHOOTING__________________________________________________________ 30
REPLACEMENT PARTS ________________________________________________________ 33
WARRANTY _________________________________________________________________ 40
INSTALLER NOTES____________________________________________________________ 44

OM-PE E V1.06 January 20, 2015
Page 3
PE1006
SPECIFICATIONS
Model PE/PEJ 1006 (catalytic)
Height Classic 29 1/8” (740 mm)
Height Parlor 33 5/8” (854 mm)
Height Ultra 35” (889 mm)
Width 27” (686 mm) (without removable bypass handle)
Depth 30 3/4” (781 mm) (without optional fan kit)
31 5/8” (804 mm) (with optional fan kit)
Flue collar 6” I.D.
Recommended flue draft .05” water column (on high burn)
Fire door opening 16 3/8” x 8 1/4” (416 mm x 210 mm)
Firebox depth 18” (458 mm) brick to brick, 20 1/2” (521 mm) brick to glass
Firebox width 21 1/8” (537 mm)
Firebox height 12 1/2” (318 mm)
Fire box capacity 2.85 cu. ft.
Recommended Fuel length 16” max. (407 mm)
Wood capacity (approximate): White oak - 60 lbs. (27.21 kg)
Fir - 40 lbs. (18.14 kg)
Construction 10 gauge & 1/4” firebox, brick lined
16 gauge outer shields
Shipping Weight 355-400 lbs. (161-182 kg)
is unit was tested and listed UL 1482 (9/88) and ULC-S627 by Intertek testing laboratories.
is unit is certied by the United States Environmental Protection Agency. Certied to comply with July, 1990
particulate emissions standards.
e following statement is required by the Environmental Protection Agency:
“is wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper
operation. It is against the law to operate this wood heater in a manner inconsistent with operating instructions
in this manual, or if the catalytic element is deactivated or removed.”

OM-PE E V1.06 January 20, 2015
Page 4 PE1006
APPLIANCE DIMENSIONS—Princess Classic PE1006BK
PRODUCT INFORMATION














 








ZRSWLRQDOIDQV












OM-PE E V1.06 January 20, 2015
Page 5
PE1006
APPLIANCE DIMENSIONS—Princess Parlor PE1006LBK
PRODUCT INFORMATION cont.



 















 
















ZRSWLRQDOIDQV










OM-PE E V1.06 January 20, 2015
Page 6 PE1006
PRODUCT INFORMATION cont.
APPLIANCE DIMENSIONS—Princess Ultra PE1006UBK








 
















ZRSWLRQDOIDQV




OM-PE E V1.06 January 20, 2015
Page 7
PE1006
CERTIFICATION LABEL

OM-PE E V1.06 January 20, 2015
Page 8 PE1006
IF THIS BLAZE KING STOVE IS NOT PROPERLY INSTALLED OR OPERATED, A HOUSE FIRE MAY
RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. CONTACT
LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM
HEATER. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY
INJURY, OR EVEN DEATH.
This appliance must be connected to a listed high temperature (ULC629 IN CANADA OR
UL-103HT IN THE USA) residential type factory build solid fuel chimney or an approved
masonry chimney with a flue liner.
Chimney and chimney connector must be in good condition and kept clean.
NEVER vent the stove to other rooms of the building. Must be vented to the outside ONLY.
NEVER use a chimney or chimney connector smaller then the stove exhaust, unless
approved by your local inspector.
NEVER vent the stove into a “Class B” gas vent chimney.
DO NOT CONNECT IN CONJUNCTION WITHANYAIR DISTRIBUTION DUCTWORK
UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS.
Inspect the chimney connector and chimney at least twice monthly and clean if necessary.
Creosote may build up and cause a house fire.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
NEVER intentionally start a chimney fire to clean the flue.
When installed in a mobile home, this appliance must be bolted to the floor and provided
with outside air. WARNING: DO NOT INSTALL IN A SLEEPING ROOM
CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED.
Check with local building officials.
If the Optional Fan Kit is
installed, connect this unit to
a properly grounded, 110-volt
electrical outlet. Do not route
the power cord in front of, or
under, the stove.
Do not make any changes or
modifications to an existing
masonry fireplace or chimney
to install this appliance. Do
not make any changes to
the appliance to increase
combustion air.
SAFETY PRECAUTIONS

OM-PE E V1.06 January 20, 2015
Page 9
PE1006
Never try to repair or replace
any part of this appliance
unless instructions are given
in this manual. All other work
must be done by a trained
technician.
Allow the appliance to cool
down before carrying out any
maintenance or cleaning.
Maintain the door and glass
seal and keep them in good
condition. A leaking door seal
will shorten burn times and
may harm the combustor.
Avoid placing wood against
the glass when loading. Do
not slam the door or strike the
glass.
Do not throw this manual
away. This manual has
important operating and
maintenance instructions that
you will need at a later time.
Always follow the instructions
in this manual.
Do not place clothing or other
flammable items on or near
this appliance.
Over firing the appliance may
cause a house fire. Never
burn the stove so hot that the
stove or chimney connector
begins to glow.
Do not use a grate or other
device to elevate the fire off of
the firebox floor. Burn the fire
directly on the bricks.
Ashes should be placed in a
steel container with a tightly
fitting lid and moved outdoors
immediately. If the ashes are
disposed of by burial in soil or
otherwise locally dispersed,
they should be retained in
the closed container until
all cinders have thoroughly
cooled. Other waste shall not
be placed in this container.
SAFETY PRECAUTIONS cont.

OM-PE E V1.06 January 20, 2015
Page 10 PE1006
36”
This appliance is designed
and approved for burning cord
wood only.
DO NOT burn trash, garbage,
artificial or paper logs, gift
wrappings, coal, lighter fluids,
chemical cleaners, chemical
starters, treated or painted
wood, driftwood or foil-backed
paper such as gum wrappers
or cigarette packages. Burn
natural wood only. It will void
all warranties and safety
listings and may damage the
catalyst .
Never burn the stove with the
loading door open. Leaving
the door cracked open may
damage the combustor.
Never block free airflow
through vents on this
appliance.
HOT WHILE IN OPERATION.
KEEP CHILDREN,
CLOTHINGAND FURNITURE
AWAY.
CONTACT MAY CAUSE SKIN
BURNS.
Do not touch the appliance
when it is hot and educate all
children of the danger of a
high temperature appliance.
Young children should be
supervised when they are
in the same room as the
appliance.
This appliance must be
properly installed to prevent
the possibility of a house
fire. The instructions must
be strictly adhered to. Do not
use makeshift methods or
compromise in the installation.
Install at least one smoke
detector on each floor of your
home to ensure your safety. It
should be located away from
the woodstove and close to
the sleeping areas. Locating
a smoke detector too close
to a woodstove can cause
the smoke detector alarm to
sound if a puff of smoke is
emitted while the woodstove
door is open during reloading.
Follow the smoke detector
manufacturers placement,
installation, and maintenance
instructions.
Keep furniture, curtains,
wood, paper and other
combustibles a minimum of
36in (914mm) away from
the front of the appliance.
ALSO, DO NOT STORE
COMBUSTIBLES UNDER
THE APPLIANCE (WOOD,
PAPER etc.).
Contact local building officials
to obtain a permit and
information on any installation
restriction or inspection
requirements in your area.
Notify your insurance
company as well.
SAFETY PRECAUTIONS cont.
DO NOT USE CHEMICALS
OR FLUIDS TO START
THE FIRE. DO NOT BURN
GARBAGE OR FLAMMABLE
FLUIDS SUCH AS
GASOLINE, NAPHTHA OR
ENGINE OIL.

OM-PE E V1.06 January 20, 2015
Page 11
PE1006
GENERAL
INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLER
WARNING: Use only the specied components listed in this manual.
e authority having jurisdiction (such a municipal building department, re department, etc.)
should be consulted before installation to determine the need to obtain a permit. Please take
time to read these instructions thoroughly. Not following the instructions could result in a faulty
installation causing serious problems. Along with these general instructions you must follow the
specic instructions which pertain to your particular installation.
Blaze King grants no warranty, implied or stated, for the installation or maintenance of the
appliance and assumes no responsibility of any consequential damage(s).
INSTALLATION INSTRUCTIONS
PARTS INCLUDED WITH THE PRINCESS
1. Poker
2. Fire Starter
3. Manual Kit
OPTIONAL EQUIPMENT
1. Convection Deck
2. Fan Kit
3. Rear Shield
4. Ash Drawer (optional on Parlor model, standard on Pedestal model)
FLOOR PROTECTION
If the stove sits on a combustible oor, a non-combustible shield must be used underneath the
stove and extending 16” out from the front and 8” on either side of the fuel-loading door in the
USA. In Canada a non-combustible shield must be used underneath the stove and extending 8”
on either side and rear and 18” out in front of the loading door.
A non-combustible shield is also required underneath the chimney connector and extending at
least 2” (50.8mm) on either side of the chimney connector.
See the next page for minimum sizes depending on model. is oor protection is required to
prevent sparks from falling onto the combustible oor. See CSA B365-M87). is product does
not require thermal hearth pad protection.
FREIGHT DAMAGE
is product was carefully inspected before it le Blaze King. Inspect the unit thoroughly upon
its arrival. If damage is found report it to the carrier and then immediately le a freight damage
claim. Blaze King will not be held responsible for damage incurred once the product leaves our
factories.

OM-PE E V1.06 January 20, 2015
Page 12 PE1006
INSTALLATION INSTRUCTIONS cont.
MINIMUM CLEARANCES for PE1006 and PEJ1006
Residential Installations A B C D E F J
Roof exit, parallel and corner. No fan kit required. 16”
410mm 9” 230mm 26.5” 675mm 16”* 410mm 14” 360mm 24.75” * 629mm 49”
Roof exit, reduced side. Use side shields. 10”
254mm 9” 230mm 20.5” 520mm 16”* 410mm 49”
Roof exit, reduced corner. Use side shields and either fan kit or rear
shield. 6” 153mm 16.75” 425mm 49”
Roof exit, close clearance. Use side shields, and either fan kit or
rear shield. 10” 254mm 6” 153mm 20.5” 520mm 13”* 330mm 49”
Wall exit, parallel and corner. No fan kit required. 16”
410mm 9” 230mm 26.5” 675mm 18”* 460mm 14” 360mm 24.75”* 629mm 49”*
Wall exit, reduced side. Use side shields. 10”
254mm 9” 230mm 20.5” 520mm 18”* 460mm 49”*
Wall exit, reduced corner. Use side shields and either fan kit or rear
shield. 7” 180mm 17.75” 451mm 49”*
Alcove, roof exit. Use side shields, and either fan kit or rear shield. 10”
254mm 6” 153mm 20.5” 520mm 13”* 330mm 49”
Mobile Home Installation
Roof exit, parallel and corner. Use side shields, either fan kit or rear
shield and outside air kit. 10” 254mm 6” 153mm 20.5” 520mm 13”* 330mm 6” 153mm 16.75” 425mm 49”
* Check with local codes and pipe manufacturer for pipe clearances. In Canada, 18” clearances from single wall pipe is required.
Alcove Dimensional Requirements:
Minimum Width 47”, Maximum Depth 48”, Minimum Height above Stove Top 49”
G = 2.5” (102mm) in USA
8” (203mm) in Canada H = 16” (406mm) in USA 18” (456mm) in Canada I = 0” (0mm) in USA 8” (203mm) in Canada K = 18” (456mm) for single wall pipe in Canada
This stove must be installed in compliance with all local codes and regulations.

OM-PE E V1.06 January 20, 2015
Page 13
PE1006
INSTALLATION INSTRUCTIONS cont.
COMBUSTION AIR
Insure adequate combustion air allowing for all other exhausting type appliances in the dwelling (range hoods,
dryers, etc.). In airtight houses it is recommended to install a fresh air inlet into the room where the stove is
located, to prevent air starvation.
VENTING SYSTEMS
e venting system consists of a chimney connector and a chimney. ese get extremely hot during use.
Temperatures inside the chimney may exceed 2000 degrees in the event of a creosote re. To protect against the
possibility of a house re, the chimney connector and chimney must be properly installed and maintained. A
listed thimble must be used when a connection is made through a combustible wall to a chimney. A chimney
support package must be used when a connection is made through the ceiling to a listed prefabricated chimney.
ese accessories are absolutely necessary to provide safe clearances to combustible wall and ceiling material.
is stove may be connected to a lined masonry chimney or a listed factory built chimney suitable for use with
solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA. Do not connect it to a chimney
serving another appliance. To do so will aect the safe operation of both appliances, and will void the stove
warranty. You must comply with the local authority having jurisdiction and/or in Canada, CSA installation
standard B365-M87.
e chimney connector must be 6” diameter, 24 MSG Black/Blue steel. Do not use aluminum or galvanized
steel. ey cannot properly withstand the extreme temperatures of a wood re. e chimney connector between
the stove and the chimney should be as short and direct as possible. Blaze King recommends the use of double
wall pipe and two 45° elbows instead of a single 90° elbow. A minimum 36” rise is recommended prior to any
elbows being used.
e chimney connector must be attached to either an approved masonry chimney or one of the listed factory
built chimneys suitable for use with solid wood fuel. All joints must be tight and fastened with sheet metal
screws.
THE CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE
AND CEILING / WALL. NEVER USE A CHIMNEY CONNECTOR TO PASS THROUGH AN ATTIC
OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING. AN
EFFECTIVE VAPOUR BARRIER MUST BE MAINTAINED AT THE LOCATION WHERE THE CHIMNEY
OR COMPONENT PENETRATES TO THE EXTERIOR OF THE STRUCTURE. ALWAYS MAINTAIN
THE MINIMUM CLEARANCES TO COMBUSTIBLES AS REQUIRED BY THE APPLICABLE BUILDING
CODES.
DRAFT
Dra is created by the heated air rising in the chimney system. is dra will pull fresh combustion air into the
rebox. Recommended dra is .05 in. w.c. operated on high. Too little dra results in a sluggish re and smoke
spillage into the room when the stove door is opened. Too much dra (over 0.06 in. w.c.) makes it unsafe to
operate the stove and will void manufacturers warranty. Use a key damper if necessary to avoid excessive dra.

OM-PE E V1.06 January 20, 2015
Page 14 PE1006
INSTALLATION INSTRUCTIONS cont.
CONNECTION TO A METAL PREFABRICATED CHIMNEY
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed
precisely. You must also purchase (from the same manufacturer) and install the ceiling support package or wall
pass through and “T” section package, re stops (when needed), insulation shield, roof ashing, chimney cap,
etc. Maintain the proper clearance to the structure as recommended by the manufacturer. is clearance is
usually a minimum of 2 inches, although it may vary by manufacturer or for certain components.
ere are basically two methods of metal chimney installation. One method is to install the chimney inside the
residence through the ceiling(s) and the roof. e other method is to install an exterior chimney that runs up
the outside of the residence (not recommended). If it is necessary to run the chimney outside, build an outside
chase around the chimney.
e chimney must be the required height above the roof or other obstruction for safety and for proper dra
operation. e requirement is that the chimney must be at least 3 feet higher than the highest point where it
passes through the roof and at least 2 feet higher than
the highest part of the roof or structure that is within
10 feet of the chimney, measured horizontally (Fig. 1).
e height requirement is necessary in the interest of
safety and does not necessarily assure proper ue dra.
Use a minimum total system height of 12 feet, measured
from the stove ue collar to the top of the chimney, not
including the chimney cap.

OM-PE E V1.06 January 20, 2015
Page 15
PE1006
INSTALLATION INSTRUCTIONS cont.
CONNECTION TO A MASONRY CHIMNEY
Masonry chimney***
Ensure that a masonry chimney meets the minimum
standards (NFPA) by having it inspected by a
professional. Make sure there are no cracks, loose
mortar or other signs of deterioration and blockage.
Have the chimney cleaned before the stove is
installed and operated. When connecting the stove
through a combustible wall to a masonry chimney,
special methods are needed.
In Canada, the wall cut away is to provide 18”
clearance for the connector. e resulting space
must remain empty. A ush mounted sheet metal
cover may be used on one side only. If covers are to
be used on both sides, each cover must be mounted
on noncombustible spacers at least 1” clear of the
wall.
***Blaze King recommends the use of a Stainless
steel liner, preferably insulated, inside a masonry
chimney. is to maintain proper dra and overall
better operation of the unit.
Your local dealer or local jurisdiction can provide details of approved methods of passing a chimney connector
through a combustible wall in your area. In USA, the National Fire Protection Association has minimum
standards to comply with. In Canada , this type of installation must conform to CAN/CSA-B365, Installation
Code for Solid Fuel Burning Appliances and Equipment.

OM-PE E V1.06 January 20, 2015
Page 16 PE1006
INSTALLATION INSTRUCTIONS cont.
MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS)
Either Rear Shield OR Fan kit are required for these installations (See next page for kits and part numbers).
Mobile home installations also requires the Outside Air Kit: Z1726B. ey are easiest to mount before the stove
is installed. See instructions packed with each kit.
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed
precisely. You must also purchase (from the same manufacturer) and install the ceiling support package, re
stops (when needed), insulation shield, roof ashing, chimney cap, etc. Maintain the proper clearance to the
structure as recommended by the manufacturer.
Chimney connector must be double wall close clearance type with either ULC629 or ULCS610 designation.
Single wall pipe is not allowed in Mobile Homes or in Alcove Installations. Insulated chimney components
must be a listed factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or
UL-103HT in the USA. For Mobile home, the chimney need to be removable to allow for transportation of the
mobile home.
DO NOT INSTALL IN SLEEPING ROOM. THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL AND CEILING / ROOF MUST BE MAINTAINED.
In mobile home installations, the stove must be securely fastened to the oor using the tie-downs provided
in the Outside Air kit. (For the pedestal model, remove the ash drawer to access the screw down holes. For the
Leg model, use the Leg Anchor Kit (P/N ZR8039) to secure stove to oor.)
ALSO, a #8 ground wire must be attached to the stove and an appropriate ground.
u
si
ng
t
he
t
ie
-d
ow
ns
p
ro
vi
de
d

OM-PE E V1.06 January 20, 2015
Page 17
PE1006
INSTALLATION INSTRUCTIONS cont.
OPTIONAL ACCESSORIES
Outside air kit, Rear Shield or Fan Kit are optional accessories, but are required for the following
installations:
MOBILE HOME INSTALLATION — Requires Outside Air Kit and Fan Kit or Rear Shield
RESIDENTIAL ALCOVE — Requires Fan Kit or Rear Shield
REAR SHIELD KIT (R/SP1006)
EITHER this Rear Shield OR the Fan Kit (P/N Z1714) is REQUIRED FOR:
MOBILE HOME, any installation
RESIDENTIAL ALCOVE
TOOLS NEEDED FOR INSTALLATION: Phillips or square drive screwdriver.
INSTALLATION : e rear shield goes across the back of the stove, just below the thermostat
knob. Place shield into position, insert and tighten the two #10 X 1-1/4" screws provided.
FAN KIT (P/N Z1714)
EITHER this Fan Kit or the Rear Shield (R/SP1006) is REQUIRED FOR:
MOBILE HOME, any installation
RESIDENTIAL ALCOVE
NOTE:Fan Kit should be installed before the stove is placed into position
INSTALLATION: See instructions included with Fan Kit. Tools needed: Square (Robertson nr. 2)
screw driver.
ELECTRICAL CONNECTION:
Your Blaze King fan kit is equipped with a three-prong (grounded) plug to decrease shock hazard.
THIS PLUG SHOULD BE INSERTED DIRECTLY INTO A PROPERLY-GROUNDED, THREE-
HOLE RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS
PLUG. Do not route the power cord in front or under the stove.
OUTSIDE AIR KIT (P/N 1726B)
REQUIRED FOR: MOBILE HOME (any installation)
e outside air inlet hose is a exible tube to bring outside air for combustion into the stove from
outside the residence, through the wall or up through the oor. e exible tube will allow some
adjustment over or around oor joists or plumbing. DO NOT CHANGE THE STRUCTURAL
INTEGRITY OF THE FLOOR. is air hose must be kept open at all times to provide outside air
for combustion.
INSTALLATION
See instructions included with the Outside Air Kit. Tools needed: 1/4" or 3/8" drill motor, Saber
saw, Saber saw wood & metal blades, 5/16" nut driver or wrench, 7/16" wrench, Small tube of
hi-heat silicone.

OM-PE E V1.06 January 20, 2015
Page 18 PE1006
INSTALLATION INSTRUCTIONS cont.
LEG KIT (Z1713BK) PARLOR MODELS ONLY
TOOLS NEEDED FOR INSTALLATION: 3/4”
wrench or socket wrench
INSTALLATION
1. Lean stove backwards to gain access to stove
bottom. NOTE: Use extreme caution
when leaning the stove over to avoid
injury or damage to the flooring or
appliance.
2. Remove four 1/2” bolts from bottom pan of
appliance. (see Fig. 1)
3. Position each leg accordingly and fasten to
stove using the removed 1/2” bolts, as well as
the supplied washer and lock washer.
(see Fig. 2)
4. Li stove back to its upright position.
5. Adjust carriage bolts in order to level stove.

OM-PE E V1.06 January 20, 2015
Page 19
PE1006
INSTALLATION INSTRUCTIONS cont.
DOOR INSTALLATION AND CHANGE-OUT
To install the door upon stove installation or to change it out, follow these steps:
WARNING: DOOR IS HEAVY, PLEASE HOLD FIRMLY.
INSTALLATION
1. Align bottom door hinge hole with bottom rebox hinge pin.
2. Lower door onto bottom hinge pin, then align top door hinge hole with top rebox hinge
pin.
3. Lower door onto pins until door hinge surface contacts rebox hinge surface.
NOTE:Ifyour door hasagold orsilver platingon it , please follow the instructions
on the PLATED DOOR & TRIM CARE card found in the manual pack.

OM-PE E V1.06 January 20, 2015
Page 20 PE1006
OPERATING INSTRUCTIONS
BYPASS
Most catalytic wood burning appliances have a bypass device to
allow the smoke from the re to temporarily bypass, or go around,
the catalytic combustor. e bypass door is located inside the
rebox at the top of the stove. e bypass is a steel plate door,
hinged inside the stove, and is controlled by the bypass handle
on the right side of the
stove. When the handle is
pointing at you, the bypass
is open, when pointing
away, it is closed. It is a
clockwise rotation from
open to close.
YOUR FIRST FIRE!
e following pages contain information on the major components and operation of your stove. Please take time
to read about them as it will give you a better understanding of how your stove works. is understanding will
help you to operate your stove properly thus will extend the life of your stove and allow you to get the highest
eciencies from your stove.
CATALYTIC THERMOMETER
is thermometer is located on the top of the stove. It’s purpose is to show you if the
Combustor is active. Always burn the stove in the “active” zone. When the combustor is not
active the stove will emit smoke and will not be ecient. For an accurate reading, turn fans
o for approximately 10 minutes and then read the thermometer.
COMBUSTOR
FLAME
SHIELD
BYPASS
DOOR
THERMOSTAT
e thermostat knob is located on the top right rear corner of the stove. It controls the burn rate of the stove
Any thermostat position between LOW(thin line) and HIGH(wide line) will produce the desired clean burning
characteristics. However, since each installation is dierent, you may nd it necessary to operate the thermostat
to suit your situation. A HIGH(wide line) thermostat setting will produce maximum heat which is more than
suitable for heating the average size home. All adjustments to the thermostat should be done gradually. When
you rst light the stove set the thermostat to HIGH(wide line) setting for 20-30 minutes, or until the re is well
established, then turn the thermostat to the desired setting. Once the re is established turn the thermostat to
MED(middle of line) for 5 minutes and then to a LOW(thin line) setting if desired. Too rapid an adjustment
may cause the stove to operate improperly. e most common mistake new owners make is continually
adjusting the thermostat.
LOW(thin line) MED(middle of line) HIGH(wide line)