manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. BleBox
  6. •
  7. Controllers
  8. •
  9. BleBox ReflectiveSwitch User manual

BleBox ReflectiveSwitch User manual

SAFETY RULES
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Do not connect the device to loads exceeding the permitted
values.
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
Connecting the device to a power supply that does not meet the
EN 60950 will invalidate the warranty.
WORLD'S SMALLEST REFLECTVE LED CONTROLLER
Before installing the controller, disconnect the voltage in the supplied circuit.
Remember that all assembly work should be carried out with the power
supply disconnected.
The controller should be mounted in a place protected from adverse environ-
or in the interior of the transparent housing of the controlled device. It is
advisable that the device is mounted in a stable and stationary position.
Familiarize yourself with the diagram and then proceed with the assembly of
the controller. Pay special attention to the designation of the controller
connectors. Start by connecting the power wires: (+) (red or black with a white
dotted line) and (-) (black).
Connect (paying attention to polarity) the LED strip. The device is equipped
with a strip of adhesive tape on the underside. Before sticking the controller,
glue it in the chosen place and hold for a few seconds. When choosing
a mounting location, remember that the sensor in the front of the device
should be placed at a distance of 3-20 mm from the detected element (eg
cabinet door or drawer wall).
Connect the device to the power supply and check that the device correctly
detects the movable element.
1INSTALLATION
1.
2.
3.
the default, as a mono-stable switch
strip when an object is detected. This mode is useful, for example, in
a cabinet that turns on the light when the door opens
mono-stable, switching on the LED strip when an object is detected,
e.g. mounted in a door frame, switching on the lighting only when the
sliding door is fully separated
bi-stable - applicable, for example, as a proximity switch, allowing you
the photo frame
Unplug the power supply for 10 seconds and then connect it again.
LED lighting will blink, it means the status will change). Repeat the
action 10 times in a maximum of 15 seconds being connected to the
supply source.
the controller will inform about the selected mode
through the blinking sequence (starts from 1): Mode 1
- sequence of 1 blink, Mode 2 - sequence of 2 blinks,
Mode 3 - sequence of 3 blinks
After the blinking sequence is repeated three times, the controller
will select that mode.
5 times the fast blinking of the connected LED lighting, informs
that it has successfully left the programming mode:
The 5 times fast blinking of the connected LED lighting informs
that the programming mode has been entered correctly:
2MODE SETTINGS
3CHANGE OF MODE
To change the work mode, perform the following steps:
CONNECTION DIAGRAM
If the moving surface is dark, it is advisable to stick a piece
of white sticker on it to improve the detection range of the
controller.
the controller will inform about the selected mode
through the blinking sequence: Mode 1 - sequence of 1
blink, Mode 2 - sequence of 2 blinks, Mode 3 - sequence
of 3 blinks
LED STRIP
110 / 230V
12 VD DC
+
power
supply
OUT
_
+
reflectiveswitch
a)
b)
c)
1 x
10 x / 15 seconds
Attention! When soldering the wires be careful not
to overheat the controller board.
TECHNICAL SPECIFICATIONS
supply voltage 12V DC
dimensions 34 x 10 x 3 mm
sensor
protection level IP00
mounting method
from -10 to + 40°C
controller
operating temperature
maximum current
maximum power
energy consumption
4A
48 W
< 0,1 W
for more information
visit our website
www.blebox.eu
or send us an
email to: [email protected]
support is available
at [email protected]

Other BleBox Controllers manuals

BleBox wLightBox v2 User manual

BleBox

BleBox wLightBox v2 User manual

BleBox wLightBox User manual

BleBox

BleBox wLightBox User manual

BleBox shutterBox 2.0 User manual

BleBox

BleBox shutterBox 2.0 User manual

BleBox shutterbox DIN User manual

BleBox

BleBox shutterbox DIN User manual

BleBox shutterbox User manual

BleBox

BleBox shutterbox User manual

BleBox wLightBox v3 User manual

BleBox

BleBox wLightBox v3 User manual

BleBox shutterbox User manual

BleBox

BleBox shutterbox User manual

BleBox GateBoxPro User manual

BleBox

BleBox GateBoxPro User manual

BleBox roller gate User manual

BleBox

BleBox roller gate User manual

BleBox windsensor PRO User manual

BleBox

BleBox windsensor PRO User manual

Popular Controllers manuals by other brands

Danfoss AK-PC 530 user guide

Danfoss

Danfoss AK-PC 530 user guide

Hedy HD700 Series Easy start guide

Hedy

Hedy HD700 Series Easy start guide

Hunter X-CORE Owners manual and programming instructions

Hunter

Hunter X-CORE Owners manual and programming instructions

Inficon Cygnus 2 operating manual

Inficon

Inficon Cygnus 2 operating manual

Pactera MARS installation guide

Pactera

Pactera MARS installation guide

EUCHIPS EULP50D-2HMC-0 quick start guide

EUCHIPS

EUCHIPS EULP50D-2HMC-0 quick start guide

Motorola MVME162P2 Series Installation and use

Motorola

Motorola MVME162P2 Series Installation and use

Realtek RTL8169 manual

Realtek

Realtek RTL8169 manual

FMS CMGZ100 operating manual

FMS

FMS CMGZ100 operating manual

Hardy HI 4050 user guide

Hardy

Hardy HI 4050 user guide

Sentera STRA4 Mounting and operating instructions

Sentera

Sentera STRA4 Mounting and operating instructions

CAL Controls CAL 9500P Abridged user manual

CAL Controls

CAL Controls CAL 9500P Abridged user manual

LED World WiFi-103 installation instructions

LED World

LED World WiFi-103 installation instructions

GSM Commander GC0321 user manual

GSM Commander

GSM Commander GC0321 user manual

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP user manual

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP user manual

Omron CPM1 - PROGRAMING  02-2001 Programming manual

Omron

Omron CPM1 - PROGRAMING 02-2001 Programming manual

Surefire BMS-300 Installation & operation manual

Surefire

Surefire BMS-300 Installation & operation manual

Rinnai CNTRLDRCIZHAW OPERATION AND CONFIGURATION MANUAL

Rinnai

Rinnai CNTRLDRCIZHAW OPERATION AND CONFIGURATION MANUAL

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.