Blix Sol User manual

Assembly Guide
Sol
®
Assembly video available
at support.blixbike.com
View on phone or desktop!
Step 5:
Install the pedals. They are marked with
an “L” for the pedal to install on the le
side of the bike and marked “R” for the
right side (side with chain and gears).
Tighten the pedals securely by turning the
pedals towards the front of the bike with
a wrench as seen in the assembly video
at support.blixbike.com. Install carefully to
not damage the thread.
Step 6:
Adjust the seat post to desired height and
firmly tighten the seat post clamp.
Step 7:
Inflate the tires to the recommended
pressure 30-50 PSI, indicated on the tire
sidewall.
Step 8: Check brakes and that all bolts
are tight before riding.
Recommended Torque Values
Tighten bolts to torque specifications to prevent the bolts from slipping.
Do not extend any components including the
stem or seat post beyond the minimum insertion
markings, which are etched into the seat post
and stem. Before using the bike, check that the
saddle post quick release bolt is closed and
firmly tightened. Secure all hardware properly or
it may become loose and result in serious injuries.

Notice: The following steps are only a general guide to
assist in the assembly of your Blix bike and not a complete
guide of all aspects of the assembly. Refer to the assembly
video at support.blixbike.com for detailed instructions. We
recommend you consult a qualified bike mechanic to assist
in the assembly, service and maintenance of your bike.
Step 1:
Remove the bike from the box and set it on a smooth, flat suace.
Remove all packaging material from the bike and carefully cut the zip-
ties attaching the handlebars and wheel to the frame. Make sure the
below items are included in the package. Contact Blix if any items are
missing.
Step 2:
Install the handlebars as shown in the assembly video at
support.blixbike.com.
1. Make sure the bend of the front fork points forward.
2. Position the handlebar stem onto
the bike so it points forward in
alignment with the front fork.
Adjust for height and angle in Step 4.
www.blixbike.com | 855-655-2549 | [e-mail] www.blixbike.com | 855-655-2549 | [e-mail]
2. Before installing the wheel onto the bike,
push the quick release skewer through
the axle of the front wheel from the side
where the disc is attached. Reattach
the spring and cap to the quick release
skewer. Make sure the smaller end of the
spring faces inwards.
3. Remove plastic fork cover.
4.Install the front wheel so that it’s fully
seated on the front fork dropouts and the
disc rotor slides into the brake caliper as
shown in the video. Tighten the quick
release firmly using your hand.
Step 4:
Fully adjust the height and angle of
the handlebar and ensure all hardware
is properly secured as shown in the
assembly video at support.blixbike.com.
1. Loosen the bolt on the handlebar
stem and adjust the stem to desired
height. Make sure to fully align the
handlebar stem with the front wheel.
Tighten the bolt firmly so that the
stem does not shi in position. (4.1)
2. Adjust the angle of the handlebar
stem to desired position using the
bolt below the handlebar stem, then
tighten. (4.2)
3. Loosen the bolt on the handlebar to
rotate the handlebar in the stem to find
your desired wrist angle. Securely fasten
the bolt to lock into position. (4.3)
Step 3:
Install the front wheel according to the detailed instructions shown in
the assembly video at support.blixbike.com.
1. Remove the cap and spring from the
quick release skewer as shown in
photo.
• The Sol
• Pedals
• Front wheel
• Quick release for front
wheel
• Battery and keys
• Charger
• Tool kit
• Manual
4.1
4.2
4.3
2.2