Blix Aveny Low-Step User manual

Assembly Guide
Aveny Low-Step
®
Assembly video available
at support.blixbike.com
View on phone or desktop!
Step 6: Install the seat. Insert the seat post. Adjust the seat post to the
desired height, and firmly tighten the quick release seat post clamp so
that it squarely closes against the collar.
Step 7: Install the pedals. They are marked with an
“L” for the pedal to install on the le side of the bike
and marked “R” for the right side (side with chain and
gears).
Tighten the pedals securely by turning the pedals
towards the front of the bike with a wrench as seen
in the assembly video at support.blixbike.com. Install
carefully to not damage the thread.
Step 8: Fully adjust the height and angle of the
handlebar and ensure all hardware is properly
secured as shown in the Aveny assembly video
at support.blixbike.com.
1. Loosen the bolt on the stem and adjust to
desired height. Make sure to fully align the
handlebar stem with the front wheel. Tighten
the bolt firmly so that the stem does not shi in
position. (8.1)
2. Adjust the angle of the handlebar stem to
desired position using the bolt below the
handlebar stem, then tighten. (8.2)
3. Loosen the bolt on the handlebar to rotate the
handlebar in the stem to find your desired
wrist angle. Securely fasten the bolt to lock
into position. (8.3)
Step 9: Inflate the tires to the recommended
pressure 40-65 PSI, indicated on the tire sidewall.
Step 10: Check brakes and that all bolts are tight before riding.
Recommended Torque Values
Tighten bolts to torque specifications to prevent the bolts from slipping.
Do not extend any components including the stem or
seat post beyond the minimum insertion markings,
which are etched into the seat post and stem. Before
using the bike, check that the saddle post quick release
bolt is closed and firmly tightened. Secure all hardware
properly or it may become loose and result in serious
injuries.
8.1
8.2
8.3

Notice: The following steps are only a general guide to assist in the
assembly of your Blix bike and not a complete guide of all aspects
of the assembly. Refer to the Aveny assembly video at support.
blixbike.com for detailed instructions. We recommend you consult
a qualified bike mechanic to assist in the assembly, service and
maintenance of your bike.
Step 1:
Remove the bike from the box and set it on a smooth, flat suace.
Remove all packaging material from the bike and carefully cut the zip-
ties attaching the handlebars and wheel to the frame. Make sure the
below items are included in the package. Contact Blix if any items are
missing.
Step 2:
Install the handlebars as shown in the assembly video at
support.blixbike.com.
1. Make sure the stem and bend of the front fork points forward.
2. Remove the handlebar clamp on the
handlebar stem installed.
3. Place center of handlebars to the
handlebar stem. Add the removed clamp
and tighten down bolts. (2.3)
Adjust for height and angle in Step 8.
www.blixbike.com | 855-655-2549 | [e-mail] www.blixbike.com | 855-655-2549 | [e-mail]
2. Attach the top part of the fender to the
attachment on the fork as shown. (3.2)
Step 4:
Install the front wheel according to the detailed
instructions shown in the Aveny assembly video at
support.blixbike.com.
1. Remove the cap and spring from the quick
release skewer as shown. (4.1)
2. Before installing the wheel onto the bike,
push the quick release skewer through the axle
of the front wheel from the side where the disc
is attached. Reattach the spring and cap to the
quick release skewer. Make sure the smaller end
of the spring faces inwards. (4.2)
3. Remove plastic fork cover.
4. Install the front wheel so that it’s fully seated on
the front fork dropouts and the disc rotor slides
into the brake caliper as shown in the video.
Tighten the quick release firmly using your hand.
5. Attach the fender struts to the attachment points
on the fork. (4.5)
Step 5: Connect the light cables to the included front light. Cable
marked with white color connects to minus (-). Install the light onto the
tab on the le side of the front fork. Attach the light to the attachment
on front of fender with the attached bolt.
Step 3: Install the the front fender and light cables according to
assembly video at support.blixbike.com.
1. Route the light cables and tube through the top of the fender. Secure
the tube through the clamps on the inside, and have them exit
through the hole at the front of the fender.
• The Aveny
• Pedals
• Front wheel
• Quick release for front
wheel
• Fender for front wheel
• Front light
• Battery and keys
• Charger
• Tool kit
• Manual
2.3
3.2
4.2
4.5
4.1