Blizzard Lighting TOURnado IP BAY User manual

1
TOURnado™
IP BAY
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Cop right (c) 2015

2
1. Summary ....................................................................................................................................................... 3
2. Safety Instruction .......................................................................................................................................... 4
3. Outside Size Picture ....................................................................................... Error! Bookmark not defined.
4. Main Function ............................................................................................................................................... 5
5. DMX Contro Function .................................................................................................................................. 6
6. Disp ay Operation instruction ....................................................................................................................... 9
6.1 DMX ADDRESS SETTING ..................................................................................................................... 11
6.2 STATIC SETTING .................................................................................................................................. 12
6.3 DMX signa se ection setting .............................................................................................................. 12
6.4 Wire ess set ........................................................................................................................................ 12
6.5 AUTO LOCK KEY SETTING ................................................................................................................... 12
6.6 COLOR CAST CALIBRATION SETTING .................................................................................................. 12
6.7 CHANNEL MODE SETTING .................................................................................................................. 13
6.8 DIMMING MODE SETTING ................................................................................................................. 13
6.9 DISPLAY SETTING ................................................................................................................................ 13
6.10 CUSTOM COLOR SETTING .................................................................................................................. 13
6.11 AUTO RUN, SELF-PROGRAM RUN ...................................................................................................... 14
6.12 EDIT SELF-PROGRAM .......................................................................................................................... 14
6.13 CHECK THE LIGHTING INFORMATION ................................................................................................ 14
6.14 LIGHTING SETTING PARAMETER RESET ............................................................................................. 14
6.15 【PROG】SELF-PROGRAMMING PARAMETER RESET ....................................................................... 15
6.16 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX CABLE ........................................... 15
7. Instruction for compatible Sweden DMX wireless module ........................... Error! Bookmark not defined.
8. Operating Contro Instruction ..................................................................................................................... 15
9. XLR cab e connecting .................................................................................................................................. 16
10. Connecting picture ...................................................................................................................................... 17
11. Troub e Shooting ......................................................................................................................................... 18
Please read over this manual before operating the light

3
1. Summary
 Summary
 Thank you for purchasing our T URNAD ™ IP BAY. Please read these instructions carefully before
operating the fixture to avoid any possible damages or accidents causes by misusage.
 Product introduction
The T URNAD ™ IP BAY fixtures feature 12x high output 5-in-1 RGBW+UV LEDs, and a highly
durable cast aluminum housing . They offer a long life span, low power consumption, great color mixing
effects, and are super bright. It features awesome built-in programs, dimming, strobe, gradual change, fading
and much more.
 Packing List
 T URNAD ™ IP BAY 1 PC
 DMX Signal Cable 1 Set
 Waterproof input power cable 1 PC
 User Manual
 Warranty Card

4
2. Safety Instruction
 Safety Notes
! Enquire the skilled people before any repair;
! Always make sure disconnect from the power source before setting up, serving and moving;.
! Avoid direct eye exposure to the fixture when it is on;
 Safety instruction
● Make sure the power supply voltage is consistent with this lights. Ensure the use of voltage is in the range
of the request technical parameter.
● Before the installation, please check the light’s fasteners and mechanical structure have been received in
good condition and appear no damage.
● This light is designed for indoor use; working temperature is lower than 40 degree.
● The fixtures maybe mounted in any position provided there is adequate room for ventilation. Make sure
there are no inflammable and explosive items (ornaments) in 0.5 meters away.
● Yellow / green cabling earthling safety; no flicker when the fixture is working on.

5
3. Dimensions
4. Main unction
 Input voltage: AC 100V-264V/47-63HZ
 Consume ： 300W
 Lamp Type ： 25W LED 5-in-1 R 、 G 、 B 、 UV 、 W (12PCS)
 Life span: 50000~100000hours
 PWM Dimmer ： 1500HZ(16666 grades)
 Control Signal ： DMX512
 Control mode ： stand alone/master/slaver
 Channel ： 16CH 、 11CH 、 10CH 、 11CH. 、 6CH 、 5CH
 Function Effect: dimmer, strobe, gradual change

6
 Touch buttons, automatic lock key
 Built-in temperature control measurement function, when LED work overheated, intelligent reduce LED
output power, current power output and temperature can be viewed
 Cooling mode: Natural Convection
 Anti-electricity intension ： 1.5KV
 Insulation Resistance:>2MΩ
 Net Weight: 13.2 Kg
5. DMX Control unction
 DMX Channels
5CH 6CH 11CH. 10CH 11CH 16CH Value unction
- CH1 CH1 - CH1 CH1 0-255 Dim all
CH1 CH2 CH2 - - - 0-255 R
CH2 CH3 CH3 - - - 0-255 G
CH3 CH4 CH4 - - - 0-255 B
CH4 CH5 CH5 - - - 0-255
UV
CH5 CH6 CH6 - - - 0-255 W
- - - CH1 CH2 CH2 0-255 R1
- - - CH2 CH3 CH3 0-255 G1
- - - CH3 CH4 CH4 0-255 B1
- - - CH4 CH5 CH5 0-255
UV 1
- - - CH5 CH6 CH6 0-255 W1
- - - CH6 CH7 CH7 0-255 R2
- - - CH7 CH8 CH8 0-255 G2
- - - CH8 CH9 CH9 0-255 B2
- - - CH9 CH10 CH10 0-255
UV 2
- - - CH10 CH11 CH11 0-255 W2
- - CH7 - - CH12
0-5 No strobe
6-115 Normal strobe(slow to fast)
116-130 No strobe
131-170 Electronic Sinewave(slow to fast)

7
171-210 pening pulse(slow to fast)
211-250 Closing pulse(slow to fast)
251-255 No strobe
- -
CH8(CH8
Prior to
CH10)
- -
CH13
(CH13
Prior to
CH15)
0-5 No effect
6-10 CT01(Call custom color in menu settint)
11-15 CT02
16-20 CT03
21-25 CT04
26-30 CT05
31-35 CT06
36-40 CT07
41-45 CT08
46-50 CT09
51-55 CT10
56-60 AUT 1
61-65 AUT 2
66-70 AUT 3
71-75 AUT 4
76-80 AUT 5
81-85 AUT 6
86-90 AUT 7
91-95 AUT 8
96-100 AUT 9
101-105 AUT 10
106-110 AUT 11
111-115 AUT 12
116-120 AUT 13
121-125 AUT 14
126-130 AUT 15
131-135 AUT 16
136-140 AUT 17
141-145 AUT 18
146-150 AUT 19
151-155 AUT 20
156-160 AUT 21
161-165 AUT 22
166-170 AUT 23
171-175 AUT 24
176-180 AUT 25
181-185 AUT 26
186-190 AUT 27
191-195 AUT 28
196-200 AUT 29

8
201-205 AUT 30
206-210 AUT 31
211-215 AUT 32
216-220 AUT 33
221-225 CHASE1
226-230 CHASE2
231-235 CHASE3
236-255 Reserved
- - CH9 - - CH14 0-255
Auto
speed,fast->slow,(AT01-AT05:0-255S,AT
06-AT33:0-25.5S)
- -
CH10(RG
B color
mixing
instead of
RGB
channel)
- -
CH15(RGB
color
mixing
instead of
RGB
channel)
Virtual colour wheel
0-10 No effect
11 Blue (Blue=full,
Red+Green+White=0)(step)
12-50 Red=0, Green->up,Blue =full,
White=0(proportional)
51 Light Blue (Red=0, Green=full, Blue =full,
White=0)(step)
52-90 Red=0, Green=full, Blue->down,
White=0(proportional)
91 Green (Red=0, Green=full, Blue =0,
White=0)(step)
92-130 Red->up, Green=full, Blue=0,
White=0(proportional)
131 Yellow (Red=full, Green=full, Blue=0,
White=0)(step)
132-170
Red=full, Green->down, Blue=0,
White=0(proportional)
171 Red(Red=full, Green=0, Blue=0,
White=0)(step)
172-210
Red=full, Green=0, Blue->up,
White=0(proportional)
211 Magenta (Red=full, Green=0, Blue=full,
White=0)(step)
212-250
Red -> down, Green=0, Blue=full,
White=0(proportional)
251-255
Blue (Red=0, Green=0, Blue=full,
White=0)(step)
- - CH11 - - CH16
0-10 Use the dimmer mode which menu had set
up
11-20 Linear curve
21-30 Square law curve

9
31-40 Inverse square law curve
41-50 S-curve
51-60 Linear curve and smooth
61-70 Square law curve and smooth
71-80 Inverse square law curve and smooth
81-90 S-curve and smooth
91-255 Use the dimmer mode which menu had set
up
6. Display Operation instruction
 MENU : access the menu or return to a previous menu option
 ENTER: select the current menu option
 UP: menu selection or parameter increments
 D WN: menu selection or parameters decrease
Menu Tree
TAB LEVEL1 LEVEL2 LEVEL3 LEVEL4
ADDR(Address)
001-512
STAT(Static
control) R1 0-255 *
G1 0-255 *
B1 0-255 *
UV 1 0-255 *
W1 0-255 *
R2 0-255 *
G2 0-255 *
B2 0-255 *

10
UV 2 0-255 *
W2 0-255 *
SHUT 0-255 *
SET(Set) SIGN(DMX signal
selection) 2.4G(wirelsee)/CABL(Cable)
WIRE(Wireless set) REST(reset) YES/N
KEY
CAL(Calibration) R 0-255
G 0-255
B 0-255
UV 0-255
W 0-255
USE YES/N
CHMD(Channel
mode) 16CH
11CH
10CH
11CH.
6CH
5CH
DIM(Dimming
mode)
LIN(linear)/SQR(square
law)/ISQR(inverse square
law)/SCUR(S-curve)/LIN.(linear
smooth)/SQR.(square law
smooth)/ISQR.(inverse square
law smooth)/SCUR.(S-curve
smooth)
DISY(Display set) N(Permanent on)
2 FF (2 minutes off)
CTST((Custom
color set) CT01 R 0-255
. G 0-255
. B 0-255
.
UV 0-255
W 0-255
CT10
AUT (Auto) AT01 RUN*
. RUN*
. RUN*
. RUN*
AT33 RUN*
ATSP(Auto speed) 0-255(S)
CHS1（Chase 1) RUN*

11
CHS2（Chase 2） RUN*
CHS3（Chase 3） RUN*
PR G
（Program） CHS1（Chase 1) SC01（Scene 1） R1 0-255
. . G1 0-255
. . B1 0-255
. .
UV 1 0-255
. . W1 0-255
. . R2 0-255
. . G2 0-255
. . B2 0-255
. .
UV 2 0-255
. . W2 0-255
. . SHUT 0-255
. . AUT N NE,AT01-AT33
. . ATSP 0-255(S)
. . TIME 0-255(S)
. . WAIT 0-25.5(S)
. . USE YES/N
. SC25（Scene 25）25
CHS3（Chase 3）
INF
（Information)
S FT(Software
version) Vx.x
TEM1(Temperature1) xxxC
TEM2(Temperature2) xxxC
P W(Power
reduction) xxx%
L AD(Load) ST L（Setting load) YES/N
PR L（Program load) YES/N
SEND(Send) YES/N
Instructions：
：：
：
When enter to the “*” position displayed on the LED, the light will automatically set as master and send data to
external. ther fixtures can receive this data and will synchronously running without manually set as slave. When
power cycle it will jump to the “*” position and running again.
6.1 DMX ADDRESS SETTING
1) Press the 【ENTER】 button in 【ADDR】 menu, then enter to the DMX address setting.
2) Press the【UP/D WN】button to select【1-512】numerical value.

12
3) Press the【ENTER】button to escape and save.
6.2 STATIC SETTING
1) Press the【ENTER】button in 【STAT】menu, then enter to the static setting.
2) Press the【UP/D WN】 button to select 【RED1】，【GREEN1】，【BLUE1】...【WHITE2】and【SHUT
】.
3) Press the【UP/D WN】button to set up the【0-255】numerical value.
4) Press the【ENTER】button to escape and save.
6.3 DMX signal selection setting
1) Press the【ENTER】button in【SIGN】menu, then enter to the DMX signal selection setting.
2) Press the【UP/D WN】button to select【2.4G】,【CABLE】
3) Press the【ENTER】button to escape and save.
6.4 Wireless set
1) Press the【ENTER】button in【WIRE】menu, then enter to the wireless set.
2)【RESET】the Analog process of press the button on again after wireless module off
3)【KEY】similar as the build-out kep
6.5 AUTO LOCK KEY SETTING
1) Press the【ENTER】button in【L CK】menu, then enter auto lock key setting.
2) Press the【UP/D WN】button to select【YES】,【N 】
3) Press the【ENTER】button to escape and save.
Instructions:
When set to [YES], it will lock automatically after two minutes to prevent accidental triggering flood
flushing, and then press any key for 10 seconds to unlock.
6.6 COLOR CAST CALIBRATION SETTING
1) Press the【ENTER】button in 【CAL】menu, then enter to the color cast calibration setting.
2) Press the【UP/D WN】button to select 【RED】，【GREEN】，【BLUE】，【 UV 】and【WHITE】.
3) Press the【UP/D WN】button to set up the【0-255】numerical value.
4) n the【USE】interface, pressing【YES】button means valid,【N 】means invalid.
5) Press the【ENTER】button to escape and save.

13
Illustrations: When pressing the【YES】button which means valid on the【USE】interface, the actual output value
of RED，GREEN，BLUE，AMBER,WHITEis output in accordance with the percentage which the color cast
calibration value divides 255.
6.7 CHANNEL MODE SETTING
1) Press the【ENTER】button in 【CHMD】menu, then enter to the channel mode setting.
2) Press the【UP/D WN】button to select【16CH】，【11CH】，【10CH】，【11CH.】，【6CH】，【5CH
】
3) Press the【ENTER】button to escape and save.
6.8 DIMMING MODE SETTING
1) Press the【ENTER】button in【DIM】menu, then enter to the dimming mode setting.
2) Press the【UP/D WN】button to select【LIN】，【SQR】，【ISQR】，【SCUR】，【LIN.】，【SQR.
】，【ISQR.】and【SCUR.】.
3) Press the【ENTER】button to escape and save.
Illustrations：When setting【LIN.】，【SQR.】，【ISQR.】and 【SCUR.】 in 【DIM】 menu, there will be
added a little delay dimming effect for smooth..
Dimming curve:
Linear curve: square law curve: Inverse Square law curve: S-curve:
6.9 DISPLAY SETTING
1) Press the【ENTER】button in【DISY】menu, then enter to the display setting.
2) Press the【UP/D WN】button to select【N】，【2 MINITES FF】
3) Press the【ENTER】button to escape and save.
6.10 CUSTOM COLOR SETTING
1) Press the 【ENTER】 button in 【CTST】 menu, then enter to the custom color setting.
2) Press the 【UP/D WN】 select 【CT01】…【CT10】

14
2) Press the【UP/D WN】button to select【1-255】numerical value.
3) Press the【ENTER】button to escape and save.
6.11 AUTO RUN, SEL -PROGRAM RUN
1)Press the【ENTER】button in【AUT 】menu, then enter to the auto run,self-program run.
2)Press the【UP/D WN】button to select【AT01】…【AT33】，【SPEED】…【CHASE03】
3)Press the【ENTER】button to start running.
6.12 EDIT SEL -PROGRAM
1) Press the【ENTER】button in【PR G】menu, then enter to the edit self-program.
2) Press the【UP/D WN】button to select【CHASE01】…【CHASE03】
3) Press the【ENTER】button for confirmation and enter to the next menu.
4) Press the【UP/D WN】button to select【SCENE01】…【SCENE20】
5) Press the【ENTER】button for confirmation and enter to the next menu.
6) Then press the【UP/D WN】button to select【RED1】…【TIME】，【WAIT】，【USE】
7) Press the【UP/D WN】button to set up the parameter which are needed.
8) Press the【ENTER】button t o escape and save.
Illustrations：When【USE】 is set to be【N 】，or the parameter of【TIME】 is 0, it will not run this scene.When
【WAIT】is set to be FADE time, the running process isas the following chart showing.
6.13 CHECK THE LIGHTING IN ORMATION
1) Press the【ENTER】button in【INF 】menu, then enter to the checking the lighting information.
2) 【S FT】button is for software version information.
3) 【TEMP1】,【TEMP2】Current temperature of lamp board.
4) 【P W】button is for the current information of power reduction.
6.14 LIGHTING SETTING PARAMETER RESET
1) Press the【ENTER】button in【ST L】menu, then enter to the lighting setting parameter reset.

15
2) Press the【UP/D WN】button to select【YES】.
3) Press the【ENTER】button to escape and save.
Illustrations： “ADDR” “CTST” and “PR G” are not reset, the others reset to the underlined value of the word.
6.15 【
【【
【PROG】
】】
】SEL -PROGRAMMING PARAMETER RESET
1) Press the【ENTER】button in【PR L】menu, then enter to the【PR G】self-programming parameter reset.
2) Press the【UP/D WN】button to select【YES】.
3) Press the【ENTER】button to escape and save.
6.16 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX
CABLE
1) Press the【ENTER】button in【SEND】menu, then enter to sending parameter to other lightings.
2) Press the【UP/D WN】button to select【YES】.
3) Press the【ENTER】button to confirm sending.
Illustrations：
1)Please disconnect the connection of projector and DMX console before sending the parameter.
2)The information of【ADDR】、【CAL】can’t be sent, can’t be downloaded each other.
3)There will be an automatic reset of the other projectors after receiving parameter correctly.
7. Instruction for compatible Sweden DMX wireless
module
1) There are 4 modes: compatible Sweden receive mode(green indicator), compatible Sweden transmit
mode(blue indicator), normal mode(yellow indicator),custom mode(red indicator)
2) After 【RESET】，and then press【KEY】to switch above modes, select needed mode and press【KEY】 one
second to confirm and save it.
3) Under compatible Sweden DMX receive mode, press 【KEY】 3 seconds to delete matching between light and
transmitter.
4) Under compatible Sweden DMX transmit mode, press 【KEY】to match receive mode, press 3 seconds will
delete matched mode.

16
5) Working in normal mode, indicator has 7 colors for option, when light and transmitter indicator are in the
same color, can receive and transmit data.
6) User-defined function is not available.
7) Notice: compatible Sweden DMX mode in this lights has complete data for sending and receiving, but
transmit function is not available here.
8. Operating Control Instruction
 Master/Slave
When the fixtures work in master mode it will send out the signal for the slave synchronous
with it. To avoid the host signal and DMX512 signals interfere with each other, should cut off the
DMX512 signals. The signal lines are longer than 60 meters (20 lamps), should increase a signal
amplifier.
9. XLR cable connecting
 XLR cable：
：：
：
The standard connection way of the XLR is: one end connects to the male plug, and the other
connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a

17
resistance120Ω （1/4W ）at the end of the DMX connecting as below:
 The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable
10. Connecting picture
 Light connecting picture：

18
11. Trouble Shooting
PR BLEM REAS N AND ACTI N
The lightin g can’t be
started normally
 Check the power connection is correct or not.
 Please detect the voltage.
 Power supply is damaged or incorrect connected. Call a
qualified personnel to fix it.
 Connection of control board is not correct. Call a qualified
personnel to fix it.
ut of console’s
control
  Please check the DMX connector and the power connection
is connected correctly or not. It means having signal if it shows
twinkling of the decimal point which in the lower right corner
of the screen when exiting the screen saver.
 Please check the DMX address setting of lighting is correct or
not.
 Check【CHMD】setting is correct or not.
 Check【SIGN】setting is correct or not.
 Please check whether the DMX line is near to the high voltage
wire or not. In that case, it will damage or interfere the DMX
electric circuit.
The beam appears
dim ,the brightness
declines obviously
 Check whether the 【CAL】is started or not and the set value is
too small.
 Check whether the【P W】is in over temperature protection
situation or not, if yes, please take measures for ventilation.