Blizzard Lighting HUSH PAR Infiniwhite 500 User manual

Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2014
HUSHPA R InfInI whIte
tM
500

Page 2
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
TABLE OF CONTENTS
HushPar™ Inniwhite 500 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The HushPar™ Inniwhite 500 5
Features 5
DMX Quick Reference 5
The HushPar™ Inniwhite 500 Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of HushPar™ Inniwhite 500 PAR Cans 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
4. Operating Adjustments 12
Navigating The Control Panel 12
Control Panel Menu Structure 13
DMX Mode 14
Master/Slave Mode 14
Sound Active Mode 14
Standalone (Program) Mode 14
Manual Color Adjustment 14
DMX Channel Values In-Depth 15
Troubleshooting 17
5. Appendix 18
A Quick DMX Lesson 18
Keeping Your HushPar™ As Good As New 19
Returns (Gasp!) 19
Shipping Issues 19
Tech Specs 20

Page 3
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x HushPar™ Inniwhite 500 Professional LED PAR Fixture
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on purchasing one of the most rocking box-shaped PAR xtures any-
where! Now that you’ve got your HushPar™ Inniwhite 500 (or hopefully, HushPares!),
you should carefully unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been damaged in transit,
notify the shipper immediately and keep the packing material for inspection. Again,
please save the carton and all packing materials. If a xture must be returned to the
factory, it is important that the xture be returned in the original factory box and pack-
ing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that
the xture you receive is suitable for your local power supply. See the label on the
xture or refer to the xture’s specications chart for more information. A xture’s
listed current rating is its average current draw under normal conditions. Check the
xture or device carefully to make sure that if a voltage selection switch exists that it is
set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied
does not match the voltage indicated on the voltage selector switch. All
xtures must be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email. We’ll be happy to
help, honest.
Blizzard Lighting
N16 W23390 Stoneridge Dr. Suite E
Waukesha, WI 53188 USA
www.blizzardlighting.com
414-395-8365
Email: [email protected]
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability
for any errors or omissions that may appear in this user manual. Blizzard Lighting™
reserves the right to update the existing document or to create a new document to
correct any errors or omissions at any time. You can download the latest version of this
document from www.blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 01/14/2014 J. Thomas 01/14/2014

Page 4
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de-
cal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup-
[email protected].

Page 5
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
2. MEET THE HUSHPAR™ INFINIwHITE 500 LED PAR
MAIN FEATURES:
• 36x 3-watt 3-in-1 Amber/Cool White/Warm White LED’s
• Full color mixing in standalone, master/slave and DMX modes
• Efcient convection cooling for zero fan noise
• Built-in automated programs via master/slave
• Built-in sound activated programs via master/slave
• Easy to use LED digital control panel
• Dual mounting yoke allows exibility in positioning
• Rugged die cast aluminum enclosure
OPTICAL:
• Installed optics: 25 degree
• Constant current driver: 500MA
• PWM Dimmer: 400HZ (16666 steps)
• Amber=590-595nm, WW=3000-3300K, CW=8000-9000K
DMX Quick Reference - 7 / 8 Channel Mode
Channel 7-Channel 8-Channel
1 Dimmer Dimmer
2 Amber Intensity Amber Intensity
3 Warm White Intensity Warm White Intensity
4 Cool White Intensity Cool White Intensity
5Strobe Strobe
6 Built-In Programs Built-In Programs
7 ACW Gradual Mixing ACW Gradual Mixing
8--- 32-bit dimmer (Set by Display
on xture) 0-4
DMX Quick Reference - 3-Channel (ACW) / 6-Channel Mode
Channel 3-Channel - ACW 5-Channel
1 Amber Intensity Dimming
2 Warm White Intensity Amber Intensity
3 Cool White Intensity Warm White Intensity
4--- Cool White Intensity
5 --- Strobe
6 --- Built-In Programs

Page 6
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
Figure 1: The HushPar™ Inniwhite 500 Pin-Up Picture
Figure 2: The Rear Connections
LED Display
DMX In DMX Out
Menu Buttons
High Power
5w 3-in-1 LEDs
Heavy-duty Die
Cast Aluminum
Enclosure
Dual Mounting
Brackets
Locking
Knobs

Page 7
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
CAUTION! The HushPar™ Inniwhite 500 utilizes a high-output
switch-mode power supply with an internal fuse. Under normal oper-
ating conditions, the fuse should not require replacement. The fuse is
eld replaceable, however it is an advanced procedure suited to quali-
ed individuals. Should your HushPar™ Inniwhite 500 fuse require
replacement, please contact Blizzard Lighting for instructions, or to
return your unit for service.
Connecting A Bunch of HushPar™ Inniwhite 500 Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the xtures on a serial data link determines the number of x-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of xtures on a serial data
link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms

Page 8
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connec-
tor (input). Note: It doesn’t matter which
xture address is the rst one connected.
We recommend connecting the xtures in
terms of their proximity to the controller,
rather than connecting the lowest xture
number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.

Page 9
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the rst xture.
2. Connect the end of the cable coming from the
rst xture which will have a (female) 3 pin connec-
tor to the input connector of the next xture con-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also re-
quire a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xutres overhead.
Adjust the
angle of the xture by loosening both knobs and tilting the xture.
After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.

Page 10
HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and different modes possible with the HushPar™ Inni-
white 500 LED are accessed by using the control panel on the rear of
the xture. There are 4 control buttons below the LED display which
allow you to navigate through the various control panel menus.
<MENU>
Is used to navigate to the previous higher-level menu item.
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
<ENTER>
Is used to select and conrm/store the current selection.
The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the rst available option for the selected
menu function. To select a menu item, press <ENTER>.
Press the <MENU> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <ENTER> button to select the menu function
currently displayed, or to enable a menu option. To return to the previ-
ous option or menu without changing the value, press the
<MENU> button.