Blizzard Lighting G-Mix 200 User manual

Blizzard Lighting, LLC
http://www.blizzardpro.com
Waukesha, WI USA
Copyright (c) 2019

Page 2
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
TABLE OF CONTENTS
G-Mix™ 200 Moving Head 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The G-Mix™ 200 5
Main Features 5
DMX Quick Reference 5
G-Mix™ 200 Pin-up Picture 6
Rear Connections 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of G-Mix™ 200 Fixtures 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting & Rigging 9
Mounting Points 10
Clamp Mounting 11
Securing the Fixture 11
4. Operating Adjustments 12
The Control Panel 12
Control Panel Menu Structure 13
DMX Values In-Depth 14
Gobo Replacement 16
Static Gobos 16
Rotating Gobos 16
5. Appendix 17
Keeping Your G-Mix™ 200 As Good As New 17
Returns (Gasp!) 17
Shipping Issues 17
Tech Specs 18
Troubleshooting 18
Dimensional Drawings 19
Photometric Data 19

Page 3
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x G-Mix™ 200
• An Ever-So-Handy Power Cord
• 1 x Set of Mounting Brackets
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on your purchase of the G-Mix™ 200! Now that you’ve got your G-Mix™
200 (or hopefully more) , you should carefully unpack the box and check the contents to
ensure that all parts are present and in good condition. If anything looks as if it has been
damaged in transit, notify the shipper immediately and keep the packing material for
inspection. Again, please save the carton and all packing materials. If a xture must be
returned to the factory, it is important that the xture be returned in the original factory
box and packing.
Powering Up!
All xtures must be powered directly o a switched circuit and cannot be run o a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
See the label on the xture or refer to the xture’s specications for more information.
The listed current rating is its average current draw under normal conditions. All xtures
must be connected to circuits with a suitable Ground (Earthing).
DISCLAIMER:
The power connector tted to the xture and xture cord are designed for compatibility
with products manufactured by Neutrik AG, Neutrik USA and their related entities, however
they are not manufactured by, aliated with or endorsed by Neutrik AG, Neutrik USA, or
any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG.
Getting A Hold Of Us
If something is wrong, please just visit our website at www.blizzardlighting.com/
support and open a support ticket. We’ll be happy to help, honest.
Note: The information and specications contained in this document are subject to change
without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors
or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right
to update the existing document or to create a new document to correct any errors or
omissions at any time. You can download the latest version of this document from www.
blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 7/7/2017 J. Thomas 3/15/2019

Page 4
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
Please read these instructions carefully. They include
important information about the installation, usage and
maintenance of this product.
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
head. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please open a support ticket at www.
blizzardlighting.com/support.

Page 5
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
2. MEET THE G-MIX™ 200
MAIN FEATURES
• 200W OSRAM® white LED light engine
• Pan: 540°/Tilt: 270° (8-16 bit resolution)
• CMY color mixing system
• 9 dichroic color lters + open
• 7 rotating, indexable and replaceable slot-n-lock glass gobos + open
• Static gobo wheel: 7 metal gobos + open
• Linear motorized zoom (5°- 42°)
• 3/8-facet bidirectional rotating prism
• Motorized linear iris and frost
• Color temperature: 6500K, CRI=80
• Linear electronic focus + auto focus
• Strobe eect with variable speed (max.15 ashes/sec.)
• Smooth dimmer from 0 - 100%
• 3/5-pin XLR male and female DMX In/Out
CONTROL:
• Protocol: USITT DMX-512
• DMX channels: 25/30-channel
• 5-button LCD control panel menu
• Operating modes: standalone, master/slave, auto
DMX Quick Reference (25/30-Channel Modes)
Channel Standard Mode (25ch) Channel Extended Mode (30ch)
1 Pan (0-540°) 1 Pan (0-540°)
2 Fine Pan (16-bit) 2 Fine Pan (16-bit)
3 Tilt (0-270°) 3 Tilt (0-270°)
4 Fine Tilt (16-bit) 4 Fine Tilt (16-bit)
5 Pan & Tilt Speed (fast <--> slow) 5 Pan & Tilt Speed (fast <--> slow)
6 Dimmer 6 Dimmer
7 Strobe/Shutter 7 Dimmer Fine
8 Cyan Intensity (0% <--> 100%) 8 Strobe/Shutter
9 Magenta Intensity (0% <--> 100%) 9 Cyan Intensity (0% <--> 100%)
10 Yellow Intensity (0% <--> 100%) 10 Magenta Intensity (0% <--> 100%)
11 Color 1 (0% <--> 100%) 11 Yellow Intensity (0% <--> 100%)
12 Color 2 (0% <--> 100%) 12 Color 1 (0% <--> 100%)
13 Color 3 (0% <--> 100%) 13 Color 2 (0% <--> 100%)
14 Static Gobo Wheel 14 Color 3 (0% <--> 100%)
15 Rotating Gobo Wheel 15 Static Gobo Wheel
16 Gobo Rotation 16 Rotating Gobo Wheel
17 Focus (0% <--> 100%) 17 Gobo Rotation
18 Zoom (0% <--> 100%) 18 Gobo Rotation Fine (0% <--> 100%)
19 Prism 1 (3-facet) 19 Focus (0% <--> 100%)
20 Prism 1 Rotate 20 Focus Fine (0% <--> 100%)
21 Prism 2 (8-facet) 21 Auto Focus
22 Prism 2 Rotate 22 Zoom (0% <--> 100%)
23 Iris 23 Zoom Fine (0% <--> 100%)
24 Frost (0% <--> 100%) 24 Prism 1 (3-facet)
25 Reset 25 Prism 1 Rotate
-- -- 26 Prism 2 (8-facet)
-- -- 27 Prism 2 Rotate
-- -- 28 Iris
-- -- 29 Frost (0% <--> 100%)
-- -- 30 Reset

Page 6
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
Figure 1: G-Mix™ 200 Pin-Up Picture
Carry
Handle
Figure 2: Rear Connections
Head/Arms
LCD
Display
200W White LED
Light Engine
Control
Buttons
Power
Input
3/5-Pin
DMX Input
Power
Switch
Fuse
Holder
Power
Output
3/5-Pin
DMX Output

Page 7
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
Remove the fuse holder from of its housing. Then take out the dam-
aged fuse from its holder and replace with exact same type of fuse.
Reattach the fuse holder, and then reconnect power.
Connecting A Bunch of G-Mix™ 200 Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the xtures on a serial data link determines the number of x-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal. The maximum recommended cable-run dis-
tance is 500 meters (1640 ft). The maximum recommended number
of xtures on a serial data link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Before replacing the fuse, disconnect the power cord.
ALWAYS replace it with the same type and rating.

Page 8
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR connec-
tor on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the
xture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5-pin DMX output connector, it’s no problem! You can simply use the in-
stalled 5-pin DMX input and/or output connections found on the back of your xture(s).
Conductor 3-Pin Female (Output) 5-Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data 1- (Primary Data Link) Pin 2 Pin 2
Data 1+ (Primary Data Link) Pin 3 Pin 3
Data 2- (Optional Secondary Data Link) Pin 4 Pin 4
Data 2+ (Optional Secondary Data Link) Pin 5 Pin 5
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the DMX cable to the female connector (output) on
the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connector
(input). Note: It doesn’t matter which
xture address is the rst one connected. We
recommend connecting the xtures in terms
of their proximity to the controller, rather than
connecting the lowest xture number rst, and
so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture to
ensure best communication.

Page 9
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3/5-pin connector side of the
DMX cable to the output (female) 3/5-pin connector
of the rst xture.
2. Connect the end of the cable coming from the
rst xture which will have a (female) 3/5-pin
connector to the input connector of the next xture
consisting of a (male) 3/5-pin connector. Then,
proceed to connect from the output as stated above
to the input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also
require a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the
xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.

Page 10
G-Mix™ 200 User Manual - Rev. C (c) 2019 Blizzard Lighting, LLC
Mounting Points
Overhead mounting requires extensive experience, which includes
calculating working load limits, knowledge of the installation material
being used, and periodic safety inspection of all installation material
and the xture. If you lack these qualications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
Caution!
Please be aware, you should have a qualied electrician performing all
of your electrical connection needs.
Be sure to complete all rigging and installation procedures before
connecting the main power cord to the appropriate wall outlet.