Blizzard POWER PLOW 810SS Supplement

BLIZZARD
POWER PLOW
®
Assembly & Operation Manual
Model 810SS Snowplow

i Table of Contents
Table of Contents
01 Snowplow Operation
02 Warning!
1999 Plow Assembly Instructions
03 Unpacking & Inspection
04 Moldboard Assembly
05 A-frame Assembly
06 Testing The Snowplow
07 Mounting & Dismounting Instructions
1999 Maintenance & Plow Specifications
08 Regular Maintenance
09 Storing Your Snowplow
10 Plow Specifications
11 Notes
1999 Plow Diagrams
12 Model 810SS Parts List
14 Model 810SS Assembly Schematic
16 Hydraulic Manifold Detail
1999 Hydraulic & Electrical Diagrams
17 Hydraulic Manifold Schematic
18 Plow Harness (Cylindrical Connector) with Diode Packs
19 Plow Harness (Cylindrical Connector)
20 Plow Harness Wire Schematic (Cylindrical Connector)
2000/01 Plow Assembly Instructions
21 Unpacking & Inspection
22 Moldboard Assembly
23 A-frame Assembly
24 Plow Wire Harness
25 Testing The Snowplow
2000/01 Maintenance & Plow Specifications
26 Regular Maintenance
27 Storing Your Snowplow
28 Plow Specifications
29 Notes
2000/01 Plow Diagrams
30 Model 810SS Parts List
32 Model 810SS Assembly Schematic
34 Hydraulic Manifold Detail
2000/01 Hydraulic & Electrical Diagrams
35 Hydraulic Manifold Schematic
36 Pistol Grip Control Wire Harness
37 Pistol Grip Control Harness Wire Schematic
38 Pistol Grip Control Extension Wire Harness
39 Pistol Grip Control Extension Harness Wire Schematic
40 Heavy-Duty Coil Wire Lead Harness
41 Heavy-Duty Coil Wire Lead Harness Wire Schematic
Troubleshooting
42 Troubleshooting Guide
Warranties
44 Limited Consumer Warranty
45 Commercial Warranty
Introduction
Congratulations on purchasing the most
advanced all-season skid steer snowplow
attachment available! The Blizzard Power
Plow Model 810SS is clearing new trails
for innovative design, rugged durability,
quality craftsmanship and superior per-
formance. Our exclusive products are
manufactured and tested in Michigan’s
Upper Peninsula, the snow capital of the
Midwest. With an annual snowfall averaging
over 250," we couldn’t imagine building
snow removal products anywhere else!
Your Blizzard Power Plow is equipped
with versatile features designed for
years of dependable service.Twelve-
inch expanding wings automatically
transform a compact 8' blade into a
massive 10' machine. Also, the inde-
pendent wings can pivot forward to form
our 9'-3" BucketBlade™ position. Now
you can carry more snow even further.
Turn your Power Plow into an all-season
skid steer blade with an easy to install
optional trip-lock assembly. This one
piece accessory replaces the standard
trip springs to provide a rigid grading
blade. Safety features include full mold-
board trip action, enclosed hydraulics
and automatic cylinder pressure relief.
To ensure years of optimum snowplow
performance, review the contents of this
manual. It contains assembly information,
detailed diagrams, complete parts listings,
maintenance guidelines and trouble-
shooting tips.
Should you need additional information,
contact your local Blizzard Power Plow
Dealer. Their knowledgeable staff is
well informed on the latest Power Plow
information. They are also your source
for replacement parts, technical assis-
tance and all service repairs.
Comments, suggestions or concerns?
Address all correspondence to:
Blizzard Corporation
Customer Service Department
95 Airpark Boulevard
Calumet, MI 49913
[phone]
[phone]
[phone] Fax

Snowplow Operation 01
Snowplow Operation
Your Blizzard Skid Steer Power Plow is the most advanced and versatile snow-
plow on the market. The easy to use controls allow you to automatically adjust
the plow blade and wings into an infinite number of plowing positions. Review
the illustrations below to determine the best position for your plowing needs.
Compact Position (8' Blade Width)
•Primary position when transporting
the snowplow
•For use in heavy snow conditions
with poor visibility, initial clearing and
tight quarters
•Ideal application: Residential driveways,
sidewalks, small roads
WidePass™ Position (10' Blade Width)
•Primary position for clearing large
surfaces
•For use in light snow conditions with
good visibility, final clearing and
clean-up
•Ideal application: Large parking lots,
widening roadways
BucketBlade™ Position
(9'-3" Blade Width)
•Primary position for transporting snow
•For use in initial clearing with decent
visibility, transporting large volumes
of snow, final clean-up
•Ideal application: Roadway intersections
WidePass™ Position Angled
with Wing Forward
•Primary position for high speed
angled plowing
•For use in directional plowing, cornering,
diverting snow away from objects or
buildings
•Ideal application: Plowing adjacent to
buildings, driveway /road intersections

02 Warning!
Warning!
Prior to operating your Power Plow, review the WARNING! label at the
passenger’s side rear of the moldboard (shown below).
Note: Read and understand all warnings indicated in this manual prior to
operating the snowplow. Warnings and cautions in the manual are indicated
by the icons shown to the left.
1. Properly mount the snowplow attachment prior to moving the skid steer.
2. Always inform persons to stand clear of the plow and skid steer attachment plates
when mounting. Failure to do so may result in serious injury or death.
3. Securely position all mounting levers prior to operating your skid steer blade.
4. Never use the plow attachment to carry people, as a man lift or work platform.
5. Always travel with the wings fully retracted.
6. Do not change the position of the blade while in transit.
7. Always lower blade when the skid steer is parked.
8. Never stand, work or reach under lift arms or lift cylinders without an approved lift
arm stop installed. Failure to do so may result in serious injury or death.
9. Use caution when plowing with down pressure. The plow attachment can cause the
front wheels on the skid steer to raise.
10. High pressure hydraulic fluid can puncture skin causing serious injury or death.
In the event of a hydraulic leak, lower load or relieve hydraulic pressure before
loosening fittings.
If injured, seek emergency medical help immediately.
Blizzard Power Plow is protected by U.S. Patents 5,899,007 and 5,638,618. Other patents pending.
READ
OWNER’S
MANUAL
THOROUGHLY
PRIOR TO
OPERATING
PLOW.
1096-2-00
WARNING
WARNING
WARNING:
CAUTION:
Should the WARNING! label or any of the labels
that came with your snowplow become hard to
read or wear off, contact your local dealer or call
our Customer Service Department at 1-888-680-
8600 for replacements.

Assem. Instructions - Unpacking & Inspection 03
Assembly Instructions - 1999
Unpacking & Inspection
Your Blizzard Power Plow has been packaged to withstand transit and
weather related damage. Fully inspect all components upon receipt of your
plow. In the event of shipping damage or missing parts, immediately contact
our Customer Service Department toll free at 1-888-680-8600.
Begin unpacking and inspection in the following order:
1. Remove packaging slip from the end panel of the pallet cover. Retain
all documentation for your records.
2. Remove the polyethylene pallet cover from the crating.
3. All wood framing should be removed from the pallet for easy access to
the snowplow.
4. Due to the odd shaped components and size of several assembly parts,
various nylon ties and corrugates are used for scratch resistance and
package orientation. Please remove these items prior to assembly.
5. Place the main blade assembly on a flat, level surface.
Once you have inspected all parts and removed all restraining and protective
packaging materials, your snowplow is ready to be fully assembled.
Pallet Cover End Panel
The tear resistant woven polyethylene pallet cover
contains a moisture barrier to help protect all
packaged components and keep out the most
inclement weather during shipping and storage.
The plow model number and the serial number of
the snowplow attachment are given together and
can be found at the end panel. The first three
digits and two letters of the number indicated is
always the plow model (810SS) and the entire
nine digit number (810SS-0001) make up the
serial number. The packaging list is also attached
to the end panel. Be sure to retain this list for
your records.

Moldboard Assembly
1. Begin the moldboard assembly by positioning the PIVOT BEAM and
A-FRAME near the connecting points at the rear of the blade between
the two center support ribs. Feed the right and left group of HYDRAULIC
HOSES protruding from the SLIDE BOX through the 1-1/2" diameter
openings in the front face of the pivot beam.
CAUTION: The hoses inside of the slide box are installed such
that they move laterally with the action of each wing. To avoid
damaging the hose connections and the wing and slide box
cylinders, pull approximately one foot of each hose grouping
toward the center of the moldboard. Verify that there is approx-
imately 12" of “slack” for each hose grouping. Reposition both
12" lengths back into the slide box – the hoses are now at a
safe travel distance for operation.
Close the slide box by installing the SLIDE BOX ACCESS PLATES.
Rest each grouping of hoses in the opening of the plates and position
the “lip” of each plate in the bottom, inside edge of both slide box
openings. Fasten each plate with two hex washer self-drilling screws.
2. Position the pivot beam between the two support ribs until the connecting
points on the beam align with those on the plow. Insert one 3/4"-10 x 3"
hex head screw through each mounting hole and secure with a 3/4"-10
top lock nut. Tighten each nut until approximately two threads appear.
CAUTION: Do not over tighten hex head nut! Binding may
prohibit the pivot beam from moving properly on the plow.
3. Hook each TRIP SPRING to the 3/4" diameter receiving holes located
on the pivot beam and connect the opposite end of the spring to their
respective EYE BOLTS. Install the four 1/2"-13 x 5" eye bolts through
the TRIP SPRING MOUNTING ANGLE on the top rear of the blade.
Secure each eye bolt by placing one 1/2" flat washer on the bolt and
thread one 1/2"-13 hex nut.Tighten each hex nut until light appears between
the coils of the spring.
4. Install the flexible BLADE GUIDES at the end of each plow wing. Insert
the 5/16"-18 x 1" hex head screw through the holes provided at the top
of the wing reinforcement rib. Tighten all screws using the top lock nuts
provided.
Congratulations! You have successfully completed the first stage of assembly
for the Blizzard Power Plow Model 810SS. In the next section you will assemble
the A-frame and the components that are attached to it.
Maximum Bolt Torque
(Dry Conditions Only)
Diameter-Thread Pitch Grade 8 (foot-pounds)
1/4"-20 11 ft-lbs
5/16"-18 24 ft-lbs
3/8"-16 44 ft-lbs
7/16"-14 70 ft-lbs
M12 x1.75 88 ft-lbs
1/2"-13 107 ft-lbs
M14x2.0 140 ft-lbs
9/16"-12 154 ft-lbs
5/8"-11 211 ft-lbs
3/4"-10 376 ft-lbs
1"-08 900 ft-lbs
Note: Use 25% less torque when lubricated.
Check and re-tighten all fasteners after the
first three hours of use. Periodically review
all fasteners after the initial inspection.
Stamped
Number
Printed
Label
All of the hoses shipped with the snowplows
contain either a stamped number on the sleeve or
a printed label applied to the hose. All numbers,
stamped or printed, correspond with the stamping
of the ports on the manifold.
****NOTICE****
If your Blizzard 810SS snowplow attachment
was shipped with a manifold that does not
contain the same port stamping as indicated
on the Sequencing Valve & Hydraulic Hose
Identification Guide (under the A-frame cover),
connect the hoses from the main blade in the
following sequence:
Hose #5 to Port #12 Hose #9 to Port #8
Hose #6 to Port #11 Hose #10 to Port #7
Hose #7 to Port #10 Hose #11 to Port #6
Hose #8 to Port #9 Hose #12 to Port #5
Hoses #1 & #2 connect to their own ports.
04 Assembly Instructions - Moldboard

Assembly Instructions - A-frame 05
A-frame Assembly
For your convenience, the MANIFOLD and ANGLE CYLINDERS have been
secured to the A-FRAME at the factory; however, each contain several
components you will need to install.
1. Begin the assembly by first removing the A-FRAME COVER. Remove
each of the 3/8"-16 x 1" hex cap screws and washers from the cover to
gain access to the hydraulic manifold.
2. Locate the HYDRAULIC ADAPTER KIT packaged with your snowplow.
Each of the 10 HOSE PORTS on the manifold contain DUST CAPS.
Replace each cap with the appropriate hydraulic adapter illustrated to the
right or review the diagram on page 16. Reference the table to the right
for proper torque specifications.
Note: All ports are identified by a stamped number on the manifold. The
numbers also identify the hydraulic functions which can be referenced on
the label under the hydraulic pump and manifold cover (shown below).
3. Once the adapters have been installed on the manifold, begin to install
the HYDRAULIC HOSES. Route each hose grouping from the pivot beam
to the access holes located on the sides of the A-frame. Connect the
hydraulic hoses to their respective adapters on the manifold. Note: The label-
ing on the hydraulic hoses should correspond with the stamped numbers
on the manifold. If the manifold received with your plow does not match
the stamping indicated on the label above, refer to the hose illustration on
page 4. Reference the table to the right for proper torque specifications.
4. Next, remove each dust cap from both of the hydraulic angle cylinder ports
and attach one 9/16"-18 x 9/16"-18 90˚ ADJUSTABLE ELBOW O.R.B.
ADAPTER to each port. Note: The cylinder ports should be facing in toward
the A-frame. Angle each adapter toward the cutting edge and tighten
approximately 1-1/2 flats. Connect the 3/8" x 20" hydraulic hose, labeled
9/16" 9/16"
7/16" 9/16"
Male O.R.B. Connector Adapter
(Port #1, #2, #6, #11)
Male O.R.B. Connector Adapter
(Port #5, #7, #8, #9, #10, #12)
Sequencing Valve & Hydraulic Hose
Identification Guide (Model 810 SS)
6
8
7
5
2
1
9
11
12
10
LSGP
ORIFICE-1
L-WINGEXT L-SLDRET
RV
RV RV RV
S4
S3 R-WINGEXT R-SLDRET RV LE
FR
ORIFICE-2
DS
S10
S9
S2
S1
BLIZZARD
CORPORATION
TM
1097-2-00
Wing Pressure Relief Valves
Angle Pressure Relief Valves
NOTE: Energize the following solenoids for the functions:
L-WINGEXT Left Wing Cylinder Extend
L-SLDRET Left Slide Cylinder Retract
R-WINGEXT Right Wing Cylinder Extend
R-SLDRET Right Slide Cylinder Retract
HYDRAULIC HOSES
SEQUENCING VALVES
1
2
5
6
7
8
9
10
11
12
Function
Right Angle
Left Angle
Right Wing Retract
Right Wing Extend
Right Slide Box Retract
Right Slide Box Extend
Left Slide Box Extend
Left Slide Box Retract
Left Wing Extend
Left Wing Retract
S1
S2
S3
S4
S9
S10
Right Slide Box Retract
Right Slide Box Extend
Angle Left
Angle Right
Left Slide Box Retract
Left Slide Box Extend
Sequence Valve
Idetification Function
Port
Idetification
The Sequencing Valve & Hydraulic Hose
Identification Guide (left) is located under the
A-frame cover.
One
Flat
Two
Flats
Torque Table for 37˚Adapters
Port
Thread
Size
Assembly
Torque
(foot-pounds)
Original
Assembly
(F.F.F.T.)
7/1 6 - 20 15 ± 1.0 2.5 ±.25
9/16-18 18 ± 2.0 2.5 ±.25
Torque Table for O.R.B. Adapters
Port
Thread
Size
Assembly
Torque
(foot-pounds)
Original
Assembly
(F.F.F.T.)
7/1 6 - 20 15 ± 1.0 1.5 ±.25
9/16-18 25 ± 2.0 1.5 ±.25
F. F. F. T. = Flats From Finger Tight
Ex.) After threading a 7/16-20 O.R.B. adapter
finger tight, torque the fitting approximately
1-1/2 flats (faces) for proper installation.
9/16"
9/16"
90˚ Adjust. Elbow O.R.B. Adapter

06 Assem. Instructions - Testing The Snowplow
#1, to the driver’s side angle cylinder adapter. Attach the 3/8" x 24"
hydraulic hose, identified by a #2, to the passenger’s side angle cylinder
adapter. Be careful not to overtighten the hose connections. Complete
the hose installation by running each hose through the access holes
in the A-frame to their respective manifold ports.
5. Once all of the hoses have been installed on the manifold, feed the
HEAVY-DUTY CYLINDRICAL CONNECTOR from the WIRE HARNESS
(on the manifold) through the top access hole in the A-frame located on
the driver’s side. The cylindrical connector, along with both pre-installed
3/4" PRESSURE & TANK HYDRAULIC HOSES, will be attached to the
skid steer when the snowplow is ready to be mounted.
6. Complete the A-frame assembly by attaching the A-frame cover. Align the
holes in the cover with those on the A-frame and replace the 3/8"-16 x 1"
hex cap screws and washers.
Congratulations! You have just completed building the finest snowplow skid
steer attachment available! However, the snowplow’s functions still need to be
tested. Follow the instructions below.
Testing The Snowplow
1. To test all of the functions on the Power Plow, your snowplow needs
to be properly attached to the skid steer. Follow the mounting procedure
on page 7.
2. Once the skid steer plate and the UNIVERSAL MOUNT PLATE on the
A-frame have been locked together (using the locking levers on the skid
steer), complete the auxiliary electrical and hydraulic connections with the
skid steer turned off. Locate both of the MALE & FEMALE FLAT-FACE
COUPLINGS provided with your snowplow. Note: Due to the various make
and model skid steers available, the couplings may not always interface
with the auxiliary hydraulic connections. Consult your skid steer’s
Operation Manual for the appropriate couplings needed. Attach the male
coupling to the 3/4" x 78" hydraulic hose that is attached to the bottom
pressure port (“P”) on the manifold. Attach the female coupling to the
remaining hose that is connected to the top tank port (“T”). Complete the
hydraulic installation by making the connections at the skid steer.
WARNING: Always use caution when connecting high-pressure
hydraulic fittings. Hydraulic fluid under pressure can puncture
skin causing serious injury or death. In the event of a hydraulic
leak, relieve hydraulic pressure before loosening fittings. If
injured, seek emergency medical help immediately.
Attach the cylindrical connector to the auxiliary electrical connection on
the skid steer. Twist the connector to lock it in place.
3. Start the skid steer and begin to initiate the Power Plow’s blade functions.
Note: Depending on the skid steer model, it may be necessary to turn on
the skid steer’s auxiliary hydraulic switch prior to operating the plow.
Upon using the integrated controls, you may notice a plow function is
slow or delayed. The hydraulic fluid is filling the cylinders and replacing
air in the system. If necessary, monitor the fluid level in your skid steer.
Also, look for any leaks around the manifold, hydraulic hoses and all cylinders.
Congratulations on a successful assembly and installation! Once all of the blade
functions have been tested, your Blizzard Power Plow is ready for action. Should
you need additional support during a plow assembly, contact our Customer
Service Department toll free at 1-888-680-8600.
The cylindrical connector allows the 810SS
Power Plow to interface with the auxiliary electri-
cal connection on most skid steer brands. This
integrated wire harness eliminates the need for
an additional snowplow control. All Power Plow
functions can be operated using the existing
controls on the skid steer.
Heavy-Duty Cylindrical
Connector & Weather Cap
3/4"
NPTF
1-1/2"
3/4"
NPTF
Female and Male
Flat-Face Couplings

Mounting & Dismounting Instructions 07
Mounting & Dismounting Instructions
B
A
B
C
SKID STEER MOUNTING &
DISMOUNTING INSTRUCTIONS
MOUNTING
1.)Position the skid steer close to the plow attachment and align the mounting
points on the skid steer plate and plow attachment plate.
2.) Tilt the skid steer plate forward and position the top edge of the plate under
the receiving pocket on the top edge of the plow attachment plate. CAUTION:
Keep fingers away from skid steer mounting points. Slightly raise the
arms on the skid steer and tilt the skid steer plate toward the cab. The attach-
ment should now be flush with the skid steer mount.
3.) Engage both locking levers on the skid steer by rotating each handle 90˚ into
a horizontal position. The attachment is now properly fastened to the skid steer.
4.) Proceed to attach both 3/4" diameter hydraulic hoses from the manifold to
the auxiliary hydraulic connectors located on the skid steer. Note: Depending
on the skid steer model, it may be necessary to initiate an auxiliary hydraulic
switch on the skid steer prior to operating the plow.
5.) Complete the mounting procedure by attaching the electrical connection on
the wire harness to the auxiliary electrical connection on the skid steer.
1095-2-00
DISMOUNTING
1.)Lower the plow on a flat, level surface and turn the engine off.
2.) Disconnect the electrical connection at the auxiliary power location.
3.) Disconnect both 3/4" diameter hydraulic hoses from the auxiliary hydraulic
connectors.
4.) Disconnect the plow attachment by rotating both of the locking levers 90˚
until they are in the vertical position.
5.) Start engine and slowly tilt the skid steer plate forward until the top edge of
the plate clears the plow attachment plate.
6.) Back skid steer away slowly – The disconnect procedure is now complete.
WARNING: Read and understand all warning labels prior
to operating your skid steer blade. Failure to follow this
instruction may result in serious injury or death.
ASkid steer plate attaches under the
top lip of the plow attachment.
BWith the plow attachment flush to
the skid steer plate, engage both
locking levers on the skid steer by
rotating each handle 90˚ into a
horizontal position. The levers will
slide through the receiving holes
in the plow attachment plate. The
plate is now securely mounted to
the skid steer.
Connect both hydraulic hoses & the
electrical harness to the skid steer.
C
Plow Attachment Lever
Receiving
Holes
Prior to operating your Power Plow, review the Mounting & Dismounting
Instructions label at the driver’s side rear of the moldboard (shown below).
Should the Mounting & Dismounting Instructions
label or any of the labels that came with your
snowplow become hard to read or wear off, contact
your local dealer or call our Customer Service
Department at 1-888-680-8600 for replacements.

08 Regular Maintenance
Regular Maintenance
Your Blizzard Power Plow Model 810SS Snowplow has been designed
for years of rugged, dependable service with low maintenance. To ensure
proper working condition, follow the maintenance guidelines below and on the
next page.
CAUTION: Always follow the maintenance guidelines in a timely
manner. Failure to observe maintenance guidelines may result in
poor snowplow operation, increased component wear or part failure.
Routinely inspect the following items and perform maintenance as needed:
1. All fasteners, pins, nuts and bolts for tightness. See the recommended
maximum bolt torque chart on page 4.
2. All hydraulic hoses and hydraulic hose adapters for wear and leaks.
3. All hydraulic cylinders for leaks; inspect rod ends for corrosion and pitting.
4. Cutting edges and plow shoes for wear.
5. Clean and lubricate the cylindrical connector periodically. Apply white lithium
grease at least once a month or every 75 hours of plow operation.
6. Lubricate the inner slide box with liquid white lithium grease. This will
provide free travel for both slide boxes.
7. Clean and cover deep scratches or exposed metal with white Blizzard
touch-up paint. Contact your local dealer for availability.
8. Monitor the hydraulic fluid level in your skid steer periodically.
Maintenance Schedule
Maintenance Performed Date