Blomberg DKC 5030 User manual

Instruction Manual

2GB
CONTENTS
Dear Customer,
Ifyoufollowtherecommendations
containedinthisInstructionManual,your
appliancewillgiveyouconstanthighper-
formance and will remain efficient for
many years to come.
RECOMMENDATIONS AND SUGGESTIONS 3
CHARACTERISTICS 4
INSTALLATION 5
USE 8
MAINTENANCE 9

3GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
fromincorrectorimproperinstallation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connecttheextractortotheexhaust flue throughapipe of minimum
diameter120mm.The route of the flue must beasshortaspossible.
• Do not connect the extractor hood to exhaust ducts carrying
combustionfumes(boilers, fireplaces, etc.).
• Iftheextractor is used in conjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
beguaranteedinthe roomin orderto preventthebackflowofexhaust
gas.The kitchen musthavean openingcommunicatingdirectly with
the open air in order to guarantee the entry of clean air.
USE
• Theextractor hood has been designed exclusively for domestic use
toeliminatekitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Neverleavehighnakedflamesunderthe hoodwhen itisinoperation.
• Adjustthe flame intensitytodirect itontothe bottomofthe pan only,
making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• Thehoodshould not beusedbychildren or persons notinstructedin
its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

4GB
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light, Blower,
Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
14.1 2 Air Outlet Connection Extension
15 1 Air Outlet Connection
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
11 6 Wall Plugs
12a 6 Screws 4,2 x 44,4
12c 6 Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual
11
12a
2.1
2.2
2
12c
12a 7.2.1 11
14.1
15
1
CHARACTERISTICS
Dimensions

5GB
INSTALLATION
Wall drilling and bracket fixing
Wallmarking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of
the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.1on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the
centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimneysectionsupplied),aligningthecentre(notch)withtheverticalline.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 306 mm above
thehorizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets using the 12ascrews (4,2 x 44,4) supplied.
• Insert the two screws 12a(4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6
mm between the wall and the head of the screw.
11
12a
306 X
116
1÷2
116
650 min.
7.2.1