Blu Stream HSP14AB User manual

HSP14AB
User Manual
70m 4-Way HDBaseT™ Splitter

HSP14AB USER MANUAL
HDP14AB User ManUal
02
contact [email protected] / [email protected]
Surge protection device
recommended
This product contains sensitive electri-
cal components that may be damaged
by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of
surge protection systems is highly
recommended in order to protect and
extend the life of your equipment.
Thank you for purchasing
this product.
For optimum performance and safety,
please read these instructions care-
fully before connecting, operating or
adjusting this product. Please keep this
manual for future reference.
Introduction
02 www.blustream.co.uk
Our HSP14AB 4K UHD HDBaseT™ splitter distributes a single
HDMI source to four simultaneous HDBaseT™ outputs. It
transmits HDMI, Bi-directional IR and PoH (PoE) up to lengths
of 70m over a single CAT cable. The 4-way splitter also features
audio breakout and EDID management.
• Features 1x HDMI input that is replicated to 4x HDBaseT™
outputs
• Extends HDMI up to distance of 70m over single CAT cable
• Supports 4K UHD video (3840 x 2160 @30Hz 4:4:4, 4096 x
2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)
• Supports all industry standard video resolutions including
VGA-WUXGA and 480i-4K
• Supports 3D signal display
• Supports all known HDMI audio formats including Dolby
TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD Master
Audio transmission
• HDMI audio input de-embedded to both analogue L/R audio
and Coaxial digital outputs concurrently
• Supports PoH (Power over HDBaseT™) to power compatible
HDBaseT™ receivers
• HDCP compliant
FEATURES:

HSP14AB USER MANUAL
HDP14AB User ManUal
03
contact [email protected] / [email protected]
1 Power LED indicator –Indicates the
status of the power for the unit.
2 Input LED indicator –Indicates if a
source is attached and is active.
3 Output LED indicator – Indicates
if a HDBT receiver is attached and
an active link is available on the
output.
Front Panel
321
HSP14AB
1 HDMI input – Connect HDMI source.
2 HDBT output LED indicator – Indicate the status of the
HDBT output.
3 HDBT outputs 1 to 4 – Connect to HDBT receivers for dis-
play output.
4 IR RX – 3.5mm stereo phone-jack, connect to IR sensor
cable.
5 IR TX – 3.5mm mono phone-jack, connect to IR transmit-
ter cable to output IR from remote areas.
6 Coaxial audio out – RCA connector, extracted audio from
HDMI input (PCM only).
7 L/R audio out – 3.5mm stereo phone-jack, extracted
audio from HDMI input, will mute if multichannel audio is
being used. (PCM stereo only)
8 DIP switcher – EDID management.
9 Power port – Use included 12V/5A DC adaptor to power
the unit.
Back Panel
3 6 7 8 91 2 4 5
EDID Control
EDID (Extended Display Identification Data) is a
data structure that is used between a display and
a source. This data is used by the source to find
out what audio and video resolutions are sup-
ported by the display then from this information
the source will determine what the best resolu-
tion is to output.
While the objective of EDID is to make connect-
ing a digital display to a source a simple plug and
play procedure issues do arise when multiple
displays or video matrix switching is introduced
because of the increased number of variables.
By pre-determining the video resolution and
audio format of the source and display device
you can potentially work around compatibility
issues associated with some display and source
combinations.
32 1 0
eDID TyPe
Combination of DIP positions
0 0 0 0 Copy EDID from output1
0 0 0 1 1080P 2.0CH
0 0 1 0 1080P 5.1CH
0 0 1 1 1080P 7.1CH
0 1 0 0 1080i 2.0CH
0 1 0 1 1080i 5.1CH
0 1 1 0 1080i 7.1CH
0 1 1 1 3D 2.0CH
1 0 0 0 3D 5.1CH
1 0 0 1 3D 7.1CH
1 0 1 0 4K 2.0CH
1 0 1 1 4K 5.1CH
1 1 0 0 4K 7.1CH
1 1 0 1 DVI 1280x1024
1 1 1 0 DVI 1920x1080
1 1 1 1 DVI 1920x1200
03
contact [e-mail] / [e-mail]

HSP14AB USER MANUAL
HDP14AB User ManUal
NOTE: Specifications are subject to change without notice.
Weight and dimensions are approximate.
DISPLAY
70m max
1 SOURCE
HSP14AB
Cat 5/5e/6
Stereo Audio
HDMI
IR Cable
HEX70B-Rx
Receiver
CONNECTION DIAGRAM
Specifications
Maintenance
Clean this unit with a so,
dry cloth. Never use alcohol,
paint thinner or benzene to
clean this unit.
04 www.blustream.co.uk
• Video Input Connectors: 1x HDMI Type A, 19-pin, female
• Video Output Connectors: 4x HDBaseT™ RJ45
• Audio Output Connectors: 1x RCA (SPDIF), 1x 3.5mm stereo jack (L/R)
• EDID: 4-pin DIP switch
• IR Input Ports: 1x 3.5mm stereo jack
• IR Output Ports: 1x 3.5mm mono jack
• Mounting kit included
• Dimensions (WxDxH): 262x145x22mm, without feet
• Shipping Weight: 0.8kg
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Power Supply: 12V/5A DC, locking type connector
• Compatible with (HDBaseT™ receivers): HEX70B-RX, or RX70AMP
• 1 x HSP14AB
• 1 x 12V/5A DC power supply
• 1 x IR emitter
• 1 x IR receiver
• 1 x Mounting kit
• 1 x User manual
Package Contents:

www.blustream.co.uk
www.blustream.com.au