manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Blue Sea Systems
  6. •
  7. Switch
  8. •
  9. Blue Sea Systems 7700B User manual

Blue Sea Systems 7700B User manual

ML–Series
Remote Battery Switch (with manual control)
PN 7700B / PN 7700100B / PN 7702B / PN 7702100B
Solenoid Switch (without manual control)
PN 7701B / PN 7701100B / PN 7703B / PN 7703100B
990180310 Rev.001
Blue Sea Systems Inc. Phone (360) 738-8230
425 Sequoia Drive Fax (360) 734-4195
Bellingham, WA 98226 USA www.bluesea.com
•Magnetic Latch (ML)—draws no current in ON or OFF state, only draws current when changing state of switch
•Deutsch harness connector for rapid connections (select models)
•Silver alloy contacts provide high reliability for switching live loads
•Manual control override knob provides an added level of safety allowing control with or without power, and
offering LOCKED OFF capability for servicing (Remote Battery Switch ONLY)
•LED output to remotely indicate switch state
•Tin-plated copper studs for maximum conductivity and corrosion resistance
•Labelrecessesforcircuitidentication
Remote Battery Switch and Solenoid Switch Specications
Cranking Rating: 10 sec. 2,500A DC
Intermittent Rating: 5 min. See Table Below
Continuous Rating See Table Below
Amperage Operating Current 100 mA when changing state
Voltage Maximum Operating 32V DC Max.
Live Current Switching 300A@12V DC—10,000 Cycles
Mechanical Endurance 100,000 Cycles
Control Circuit Voltage 10.1 to 16.5V (12V models), 20.2 to 32.9V (24V models)
Terminal Stud Size 3/8"-16
MaximumTerminalStudTorque 140in-lb(15.5N•m)
Ring Terminals Size 3/8", M10
Terminal Ring Diameter Clearance 1.12”(28.4mm)
Harness Connector: (select models) Deutsch DTM Series DTM 06-6S
Mating Part Requirements: (see LADD Industries www.laddinc.com)
Receptacle Shell DTM-04-6P*
Wedgelock WM-6P
Terminal Pins 1060-20-0122†
Sealing Plugs 0413-204-2005†
Hand Crimp Tooling DTT-20-0‡
Remote Control Switch (sold separately) Momentary SPDT (ON)-OFF-(ON) or two momentary push
button switches,100mA rating Min.
Regulatory: Meets ISO 8846 and SAE J1171 external ignition protection requirements, Rated IP66
* Special modifications are available depending on customer requirements. No polarization on standard product.
†Quantity depends on optional wire connections. The total number of pins and sealing plugs is 6.
‡Required for hand assembly of wires and terminal pins.
Marine Electrical Prod
ucts
Remote Battery Switch
PN Termination Manual
Control
Control
Circuit
7700B Tinned Wires Yes 12V DC
7700100B Deutsch Connector Yes 12V DC
7702B Tinned Wires Yes 24V DC
7702100B Deutsch Connector Yes 24V DC
Overview of Application
To connect battery bank to load, or combine
battery banks
Momentarily depress control switch actuator to “ON”.
Optional remote LED indicates closed connection.*
To disconnect battery bank from load, or
isolate battery banks that are connected
Momentarily depress control switch actuator to
“OFF”.*
The ML-Series Remote Battery Switch/Solenoid Switch provides high-current carrying and
switching under load. The Remote Battery Switch/Solenoid Switch is installed close to the battery banks.
A single pole double throw (SPDT) Control Switch Panel, or two momentary push button switches
(sold separately), operate the Remote Battery Switch/Solenoid Switch. Control Switches are installed in a
convenient location near other electrical controls or companionway (see Illustrations on reverse).
The Manual Control Override Knob provides (Remote Battery Switch Only):
• anaddedlevelofsafetythatallowsmanualON-OFFcontrolwithorwithoutpower
• LOCKOFFforservicingtheelectricalsystem
A remote LED (sold separately) indicates a closed connection between battery bank and load, or between
two battery banks when used as an emergency cross-connect.
Remote Operation. A momentary (SPDT) (ON)-OFF-(ON) control switch or two momentary push button
switches (sold separately) can provide cross connect and/or battery isolation. The control switch should be
mounted in a convenient location near helm controls to allow for quick access.
Emergency Manual Control Override Operations (Remote Battery Switch Only)
* If the Control Switch is held ON or OFF for 5 seconds, the internal coil protection will engage and the
Remote Battery Switch/Solenoid Switch will not respond to further remote input for approximately
10 seconds.
To connect battery bank to load,
or combine battery banks
With Override Knob in (REMOTE position),
push button until latched (Push to Latch On).
To disconnect battery bank from
load, or isolate battery banks that
are connected
Rotate Override Knob to right to release button
from Latch On mode (button pops up). Rotate
Override Knob to left (REMOTE position).
To prevent remote operation Rotate Override Knob to right
(LOCK OFF position).
To secure for servicing With Override Knob in (LOCK OFF position),
pass cable tie through hole.
12
Solenoid Switch
PN Termination Manual
Control
Control
Circuit
7701B Tinned Wires No 12V DC
7701100B Deutsch Connector No 12V DC
7703B Tinned Wires No 24V DC
7703100B Deutsch Connector No 24V DC
Wire Size Intermittent Rating 5 min. Continuous Rating
2/0 400 Amps 225 Amps
4/0 400 Amps 300 Amps
2x (4/0) 700 Amps 500 Amps
CONTROL SWITCH
(not included)
Momentary SPDT
(ON)-OFF-(ON)
AB
START
BATTERY
ENGINE
GROUND
LED OUTPUT
+VDC, TO OPEN
+VDC, TO CLOSE
+VDC, 24 HR.
1
2
3
6
4LED
1
2
3
+8 -7
+VDC, 24 HR. (RED)
AB+VDC, TO CLOSE (BRN)
+VDC, TO OPEN (ORG)
LED OUTPUT (YEL)
GROUND (BLK)
START
BATTERY
ENGINE
LED
1
2
3
+8 -7
CONTROL SWITCH
(not included)
Momentary SPDT
(ON)-OFF-(ON)
Installation Instructions
Installation Instructions
Mounting
Install as close as possible to battery bank. To avoid corrosion to connecting wires and terminals, mount in
a dry and protected location. Avoid mounting directly above vented lead acid batteries so that the Remote
Battery Switch/Solenoid Switch is not exposed to corrosive gasses expelled from the batteries.
High Current Primary Circuit Connections (stud terminals A and B)
For help selecting the appropriate wire size and circuit protection rating, go to www.bluesea.com and click the
Circuit Wizard quick link.
NOTE: Stud terminals A and B are interchangeable. The load can be connected to A or B; the battery bank
can be connected to A or B.
To connect high current circuit wires:
1. Connect the battery bank to one of the stud terminals marked A or B.
2. Connect the load to the other stud terminal marked B or A.
3.Torquethehighcurrentterminalstudnutsto140in-lbs(15.5N•m)maximum.
NOTE: If switching an inverter, windlass, bow thruster, etc., the circuit wires must have circuit protection to
comply with ABYC guidelines. Wires used for engine starting do not required circuit protection.
Control Circuit Connections (wires contained in the wire harness)
NOTE: The Remote Battery Switch/Solenoid Switch is designed to be controlled by a momentary
SPDT switch, or two momentary push button switches. Use 16 AWG wire for the Control Circuit.
To connect DC power to the Remote Battery Switch/Solenoid Switch Control Circuit:
1. Connect the red wire through a 10A (min) circuit protection device to DC+. The power source should be
a direct connection to the battery.
2. Connect the black wire to DC ground.
To connect a momentary SPDT Control Switch: (sold separately)
1. Connect the common load terminal of the Control Switch through a 2A (min) circuit protection device
to DC+. Use a 24-hour power source (connected directly to the battery.)
2. Connect the brown wire to the CLOSE side of the Control Switch.
3. Connect the orange wire to the OPEN side of the Control Switch.
Optional Remote Indicator Connection: (sold separately)
Use Blue Sea Systems LED 8033 (amber), 8171 (red), or 8172 (green). Install in a convenient location close
to Control Switch.
To connect a remote LED indicator:
1. Connect the red wire of the LED to a circuit protected positive source.
2. Connect the yellow wire of the LED to the yellow wire of the Remote Battery Switch/Solenoid Switch
Tinned Wire Termination (PNs 7700B, 7702B, 7701B, and 7703B) or the LED output of the Deutch DTM
Connector Termination (PNs 7700100B, 7702100B, 7701100B, and 7703100B)
4.500"
114.30mm
3.000"
76.20mm
5.470"
138.94mm
3.750"
95.25mm
2.030"
51.56mm
1.900"
48.26mm
1.030"
26.16mm
Tinned Wire Termination
Deutsch DTM Connector Termination
Front View Side View
Bottom View
Guarantee
AnyBlueSeaSystemsproductwithwhichacustomerisnotsatisedmaybereturnedforarefundor
replacement at any time.
]These instructions are intended to provide assistance with the installation of this product, and are
not a substitute for a more comprehensive understanding of electrical systems. We strongly
recommend that a competent electrical professional perform the installation of this product.
]The illustrated wiring diagram represents a common installation and is not meant to be a guide for wiring
 aspecicvessel.Thewiringdiagramshowsasinglebatterybankinstallation.
]Disconnect all negative battery connections before beginning the installation.
]All unused control wires should be carefully insulated from each other and from accidental contact
using heat shrink tubing or electrical tape. External contact or shorting between control wires can lead
to malfunction.
CAUTION

This manual suits for next models

7

Other Blue Sea Systems Switch manuals

Blue Sea Systems 9010 User manual

Blue Sea Systems

Blue Sea Systems 9010 User manual

Blue Sea Systems 8280 User manual

Blue Sea Systems

Blue Sea Systems 8280 User manual

Blue Sea Systems Dual Circuit 6010 User manual

Blue Sea Systems

Blue Sea Systems Dual Circuit 6010 User manual

Blue Sea Systems 9019 User manual

Blue Sea Systems

Blue Sea Systems 9019 User manual

Blue Sea Systems 3001 User manual

Blue Sea Systems

Blue Sea Systems 3001 User manual

Blue Sea Systems 3003 User manual

Blue Sea Systems

Blue Sea Systems 3003 User manual

Blue Sea Systems 6005 User manual

Blue Sea Systems

Blue Sea Systems 6005 User manual

Blue Sea Systems 9001e User manual

Blue Sea Systems

Blue Sea Systems 9001e User manual

Blue Sea Systems 3000 User manual

Blue Sea Systems

Blue Sea Systems 3000 User manual

Blue Sea Systems 7700 User manual

Blue Sea Systems

Blue Sea Systems 7700 User manual

Blue Sea Systems 3002 User manual

Blue Sea Systems

Blue Sea Systems 3002 User manual

Blue Sea Systems 7712 User manual

Blue Sea Systems

Blue Sea Systems 7712 User manual

Blue Sea Systems 9004e User manual

Blue Sea Systems

Blue Sea Systems 9004e User manual

Blue Sea Systems 8689 User manual

Blue Sea Systems

Blue Sea Systems 8689 User manual

Blue Sea Systems 6006 User manual

Blue Sea Systems

Blue Sea Systems 6006 User manual

Blue Sea Systems ML Series User manual

Blue Sea Systems

Blue Sea Systems ML Series User manual

Blue Sea Systems 8361 User manual

Blue Sea Systems

Blue Sea Systems 8361 User manual

Blue Sea Systems 8687 User manual

Blue Sea Systems

Blue Sea Systems 8687 User manual

Blue Sea Systems 8369 User manual

Blue Sea Systems

Blue Sea Systems 8369 User manual

Popular Switch manuals by other brands

iNels RFSA-61B manual

iNels

iNels RFSA-61B manual

Bones TWIN-CITY AB/Y owner's manual

Bones

Bones TWIN-CITY AB/Y owner's manual

METRObility Optical Systems CenturyStack 8124-01-M Installation and user guide

METRObility Optical Systems

METRObility Optical Systems CenturyStack 8124-01-M Installation and user guide

LEGRAND 5 745 03 user guide

LEGRAND

LEGRAND 5 745 03 user guide

StarTech.com VS221HD4KA quick start guide

StarTech.com

StarTech.com VS221HD4KA quick start guide

Lantech IPGS-5400-2P user manual

Lantech

Lantech IPGS-5400-2P user manual

Dataprobe 4P-MAS quick start guide

Dataprobe

Dataprobe 4P-MAS quick start guide

Advantech EKI-7659CPI user manual

Advantech

Advantech EKI-7659CPI user manual

Intercoax ECP-2808RM user manual

Intercoax

Intercoax ECP-2808RM user manual

NETGEAR FSM726E - ProSafe Switch Hardware installation guide

NETGEAR

NETGEAR FSM726E - ProSafe Switch Hardware installation guide

DANLERS CEFL PIR LR Installation notes

DANLERS

DANLERS CEFL PIR LR Installation notes

Vimar 6592 Installer's guide

Vimar

Vimar 6592 Installer's guide

Analog way Pulse quick start guide

Analog way

Analog way Pulse quick start guide

Linksys EF24G2 - EtherFast Dual Gigabit Specifications

Linksys

Linksys EF24G2 - EtherFast Dual Gigabit Specifications

Avaya C360 Manager Quick start for hardware installation

Avaya

Avaya C360 Manager Quick start for hardware installation

LevelOne GEU-0520 Qig manual

LevelOne

LevelOne GEU-0520 Qig manual

MiLAN MIL-SM801XX user guide

MiLAN

MiLAN MIL-SM801XX user guide

ABB TX series Operating instructions manual

ABB

ABB TX series Operating instructions manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.