Blue Whale Spa TP600 User manual

Changing your range between LOW/HIGH
•Press WARM/TEMP
•Press LIGHT (you will see TEMP with the RANGE flashing)
•Press WARM/TEMP (this should change the arrow between up and down –We recommend a HIGH range –The
arrow pointing up to allow you to heat to the maximum temperature)
•Press LIGHT
If the RANGE is LOW –the tub will only heat to 37°C
Changing the mode
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT
•Press WARM/TEMP (this will change between REST and READY –We recommend, for regular use to keep it in a
READY mode)
•Press LIGHT
Please be aware, if in REST mode, you will see RUN PMPS FOR TEMP appear on your control panel
Checking/Changing your Time
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT repeatedly (until SET –TIME appears)
•Press WARM/TEMP
•Press WARM/TEMP (until the correct hour is displayed)
•Press LIGHT
•Press WARM/TEMP (until the correct minute is displayed)
•Press LIGHT
Checking/Adjusting your Filtration Cycle
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT repeatedly (approx 6 times) until FLTR1 appears
•Press WARM/TEMP (your should see BEGN on your LCD)
•Press WARM/TEMP (you should see the time and the HOURS flashing)
oIf you want to change the HOUR press WARM/TEMP until the hour you desire appears and then press
LIGHT to save –This will change it to the minutes
oIf you want to change the the MINUTES press WARM/TEMP –This will adjust the minutes in 15min
increments, then press LIGHT to save (you should then see RUN on your LCD)
•Press WARM/TEMP (we advise to set your filtration cycle for 2hrs –If it is not set for 2hrs, please follow the
below)
oPress WARM/TEMP until 2hrs is dsplayed on the HOURS and then press LIGHT to save –This will
change it to the minutes
oIf you want/need to change the MINUTES then press WARM/TEMP –This will adjust the minutes in
15min increments, then press LIGHT to save (you should then see ENDS on your LCD –This will just
show the end time –You can check this is right, however it isn’t really necessary
•Press LIGHT
•Press LIGHT (you should see FLTR2 appear on your LCD –If it does not, press LIGHT once more. You may then see
OFF. If you see OFF, please press WARM/TEMP until you see ON
•Press LIGHT
oYou will then see BEGN and can now repeat the steps as above

Locking/Unlocking your Control Panel
To LOCK TEMP (the temperature and any temperature settings, including but not limited to the RANGE, MODE will be
locked)
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT (until LOCK appears)
•Press WARM/TEMP
•Press WARM/TEMP (you will see OFF)
•Press WARM/TEMP (until you see ON)
•Press LIGHT
To LOCK PANL (no functions can be used although the automatic settings are still in place, including but not limited to the
Filtration Cycle and Heating facility)
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT (until LOCK appears)
•Press WARM/TEMP
•Press LIGHT (you will see PANL)
•Press WARM/TEMP (you will see OFF)
•Press WARM/TEMP (until you see ON)
•Press LIGHT
To UNLOCK
•Press and hold WARM/TEMP
•Press LIGHT slowly twice
To Flip your display
•Press WARM/TEMP
•Press LIGHT
•Press LIGHT (until FLIP appears)
•Press WARM/TEMP (until display is as you desire)
•Press LIGHT
Changing your Preferences/Turning OFF Reminders (ie: CLN FLTR)
➢Switching between °C/°F
•Press WARM/TEMP
•Press LIGHT (approx. 8 times until PREF appears)
•Press WARM/TEMP
•Press WARM/TEMP (choose °C or °F when displayed)
•Press LIGHT
➢Turning off Reminders
•Press WARM/TEMP
•Press LIGHT (approx. 8 times until PREF appears)
•Press WARM/TEMP
•Press LIGHT (until RE –MIN –DERS appears)
•Press WARM/TEMP
oIf it says ON, press WARM/TEMP until OFF is displayed
•Press LIGHT